udhcpc taking 100% CPU in 1.9.2.7-9

[wiz]

Ok, try 9.2.2 and 9.2.3. Start with 9.2.3 and if it works, then there is no need to check 9.2.2.

Right, version 1.9.2.7-9.2.3 is in at the moment, will evaluate this today to see what happens.

cheers,

Wiz

[dholliday]

Release 9.2.3 works OK for now. udhcpc does not take all CPU

[dholliday@mig root]$ uptime
 13:45:03 up 17:20, load average: 0.02, 0.01, 0.00

[wiz]

well, not if you use automatic IP. I am half way past the leasetime, so it is time for renewalls.

this is what I see:



I'll proceed in putting the 9.2.2 version in to see if that works.

regards,

wiz

[sesamebike]

1.9.2.7-9.2.3 doesn't work for me either.

Mem: 13696K used, 268K free, 0K shrd, 2088K buff, 5648K cached
CPU:  98% usr   1% sys   0% nice   0% idle   0% io   0% irq   0% softirq
Load average: 1.46 1.19 1.07
  PID  PPID USER     STAT   VSZ %MEM %CPU COMMAND
  176     1 admin    R     2712  19%  98% udhcpc -i eth1 -p /var/run/udhcpc0.pi
 3342  3339 admin    R     1792  13%   1% top

[admin@wl500g root]$ uptime
 18:45:36 up 20:49, load average: 1.08, 1.13, 1.06

I'll load 9.2.2 now.

[wiz]

9.2.2 does exactly the same here.

So far the only one that worked was 9.2.1.

I'll put that one back in in a minute. So 9.2.2 does clog the cpu when it is renewall time too..

[Oleg]

Uploaded 9.2.4, try it too.

[wiz]

Uploaded 9.2.4, try it too.

ok, will put that one in.

cheers,

wiz

[wiz]

9.2.4 works for me!

Apr  5 23:30:39 udhcpc[143]: Lease of myIPaddress obtained, lease time 14400
Apr  6 01:30:42 udhcpc[143]: Lease of myIPaddress obtained, lease time 14400
Apr  6 03:30:44 udhcpc[143]: Lease of myIPaddress obtained, lease time 14400
Apr  6 05:30:47 udhcpc[143]: Lease of myIPaddress obtained, lease time 14400
Apr  6 07:30:49 udhcpc[143]: Lease of myIPaddress obtained, lease time 14400

cheers,

Wiz

[sesamebike]

Wiz is one step ahead of me. I can confirm that 9.2.2 doesn't work for me either. I'll load 9.2.4 now.

[Oleg]

Ok, try 9.2.5 now.

[wiz]

will do that tomorrow. If that one does not work I don't have time to fix it until I get back from work, so tomorrow afternoon that one will go in.

Will keep you posted Oleg.

cheers,

Wiz

[sesamebike]

9.2.4 seems to work for me as well. Been running it for 23 hours now without any excessive cpu usage from udhcpc.

I'll load 9.2.5 now anyway. Anything in particular that I should look for?

[Oleg]

Just flash it. 9.2.5 seems to be the final in this saga.

[dholliday]

Afternoon I'll try 9.2.5, but I don't have problems even with 9.2.3. Anyway, I'll try it and if it'll work I'll keep 9.2.5 or which would be the final version in this super fast problem solving saga. I can't even keep up with all new releases.

Thank you very much, Oleg!
Thanks also to others who are testing new releases.

[wiz]

9.2.5 is in at the moment. see what happens over the next couple of hours.