The final part of my post.
$ ps w
As you can see dropbear should be running, because it's launched in /usr/local/sbin/post-firewall. I have disabled the default dropbear in the web GUI.Code:PID USER VSZ STAT COMMAND 1 god 1312 S /sbin/init 2 god 0 SW [keventd] 3 god 0 SWN [ksoftirqd_CPU0] 4 god 0 SW [kswapd] 5 god 0 SW [bdflush] 6 god 0 SW [kupdated] 7 god 0 SW [mtdblockd] 38 god 1108 S httpd eth1 39 god 1072 S nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan 41 god 1516 S syslogd -m 0 -O /tmp/syslog.log -S -l 7 -b 2 42 god 1516 S klogd 44 nobody 832 S dnsmasq 45 god 0 SW [khubd] 57 god 1316 S watchdog 63 god 0 SW [usb-storage-0] 64 god 0 SW [scsi_eh_0] 73 god 0 SW [kjournald] 74 god 0 SW [kjournald] 84 god 6304 S N /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config 85 god 6304 S N /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config 86 god 6304 S N /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config 97 god 1516 S sh -c ps w > /tmp/syscmd.log 2>&1 98 god 1516 R ps w
$ lsmod
No et module?!?Code:Tainted: P usb-storage 63080 3 sd_mod 12660 6 scsi_mod 72624 2 [usb-storage sd_mod] ehci-hcd 28212 0 (unused) usb-uhci 27412 0 (unused) usbcore 78840 1 [usb-storage ehci-hcd usb-uhci] ip_nat_ftp 3136 0 (unused) ip_conntrack_ftp 4584 1 wl 897336 0 (unused)
$ ifconfig
No ethernet drivers? I suppose eth0 is the wireless card.Code:br0 Link encap:Ethernet HWaddr 00:1E:8C:72:28:ED inet addr:192.168.100.1 Bcast:192.168.100.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2909 errors:0 dropped:0 overruns:0 frame:0 TX packets:4307 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:237804 (232.2 KiB) TX bytes:4382975 (4.1 MiB) eth0 Link encap:Ethernet HWaddr 00:1E:8C:72:28:ED UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2872 errors:0 dropped:0 overruns:0 frame:339 TX packets:4439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:274156 (267.7 KiB) TX bytes:4435594 (4.2 MiB) Interrupt:12 Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1 RX packets:2806 errors:0 dropped:0 overruns:0 frame:0 TX packets:2806 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:568755 (555.4 KiB) TX bytes:568755 (555.4 KiB)
$ route -an
Code:Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.1 0.0.0.0 255.255.255.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
$ netstat -an
So httpd and transmission are listening. As you can see I'm controlling the router through httpd, as it is the only way to reach it.Code:Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:9091 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:51413 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 192.168.100.1:80 192.168.100.38:55439 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55435 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55443 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55438 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55434 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55442 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55437 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55445 ESTABLISHED tcp 0 0 192.168.100.1:80 192.168.100.38:55441 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55436 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55444 TIME_WAIT tcp 0 0 192.168.100.1:80 192.168.100.38:55440 TIME_WAIT udp 0 0 127.0.0.1:34954 0.0.0.0:* udp 0 0 0.0.0.0:53 0.0.0.0:* udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 0.0.0.0:51413 0.0.0.0:* Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node Path unix 4 [ ] DGRAM 259 /dev/log unix 3 [ ] STREAM CONNECTED 595 unix 3 [ ] STREAM CONNECTED 594 unix 2 [ ] DGRAM 367 unix 2 [ ] DGRAM 366
$ mount
All ok here?Code:rootfs on / type rootfs (rw) /dev/root on / type squashfs (ro) none on /dev type devfs (rw) proc on /proc type proc (rw) tmpfs on /tmp type tmpfs (rw,noatime) usbfs on /proc/bus/usb type usbfs (rw) /dev/discs/disc0/part2 on /opt type ext3 (rw,noatime) /dev/discs/disc0/part3 on /tmp/mnt/disc0_3 type ext3 (rw,noatime)
$ ls -la /usr/local/sbin/
These are my startup scripts. N.B. pre-boot is empty.Code:total 312 drwxr-xr-x 2 god root 220 Jan 1 2000 . drwxr-xr-x 5 god root 120 Jan 1 2000 .. -rwxr-xr-x 1 god root 268 Dec 2 17:06 ez-setup -rwxr-xr-x 1 god root 9836 Nov 18 15:30 knock -rwxr-xr-x 1 god root 273100 Nov 18 15:30 knockd -rwxr-xr-x 1 god root 24 Dec 2 18:50 post-boot -rwxr-xr-x 1 god root 798 Dec 3 09:25 post-firewall -rwxr-xr-x 1 god root 45 Dec 2 17:12 post-mount -rwxr-xr-x 1 god root 0 Nov 18 17:43 pre-boot -rwxr-xr-x 1 god root 330 Dec 2 17:11 pre-mount -rwxr-xr-x 1 god root 170 Dec 2 17:13 pre-shutdown
$ cat /usr/local/sbin/post-boot
Code:#!/bin/sh rmmod printer
$ cat /usr/local/sbin/post-firewall
Code:#!/bin/sh LAN_IP="$(nvram get lan_ipaddr)" #WAN_IP="$(nvram get wan_ipaddr)" # My own firewall rules: # remove the default DROP rule iptables -D INPUT -j DROP # Open ports for transmission iptables -A INPUT -p tcp --dport 51413 -j ACCEPT iptables -A INPUT -p udp --dport 51413 -j ACCEPT # append the default DROP rule iptables -A INPUT -j DROP # ------------------------------------------------- # start dropbear on LAN /usr/sbin/dropbear -p $LAN_IP:22 # start dropbear on WAN # -s = no password logins #/usr/sbin/dropbear -s -p $WAN_IP:2222 # Launch knockd on WAN #/usr/local/sbin/knockd --daemon --interface eth1 --config /usr/local/etc/knockd/knockd.conf
$ cat /usr/local/sbin/post-mount
One remark about starting rc.unslung in post-mount: now everytime I plug in a USB flash drive, a new process of transmission is launched because rc.unslung launches it.Code:#! /bin/sh /opt/etc/init.d/rc.unslung start
$ cat /usr/local/sbin/pre-mount
Code:#! /bin/sh swapon -a # I commented out this part of wengi's script cause I want mail notification # when the file system needs checking. Don't know how to do it yet. # #for i in `awk '/ext3/{print($1)}' /etc/fstab` ; do # if [ -b $i ] ; then # grep -q $i /proc/mounts || e2fsck -p $i 2>&1 | logger -t e2fsck # else # logger -t fstab "$i is not attached" # fi #done
$ cat /usr/local/sbin/pre-shutdown
Thanks for reading!Code:#! /bin/sh /opt/etc/init.d/rc.unslung stop sleep 10s for i in `cat /proc/mounts | awk '/ext3/{print($1)}'` ; do mount -oremount,ro $i done swapoff -a sleep 1s




