Did you change the default IP from 192.168.1.1 to something else? Then it could be the new one in recovery mode as well.
Type: Posts; User: MMCM
Did you change the default IP from 192.168.1.1 to something else? Then it could be the new one in recovery mode as well.
Use a fixed IP in the 192.168.1.0/24 network when using the recovery tool.
You could use the tftp program to send the firmware without the this tool from the windows command line (use the binary...
Offensichtlich stammen sind diese Logeinträge von Brute-Force-Angriffen auf den ssh Server.
Für jede neue Verbindung wird auch ein neuer Prozess gestartet.
Es gibt mehrere Varianten, dieses zu...
Sind die (automatischen?) DNS Einträge korrekt?
I am using such an Adapter on an older Compaq, and I had to set a BIOS delay of 15 seconds, but that still does not work 100% of the time, especially when doing a reboot.
If you search the forum, you will notice that the cause of solid lan leds mostly is a defect power supply. With shortening the wrong pins you can damage your router and produce a definite brick.
I...
If you want a file server with good performance don't mess around with soho routers. Build a system yourself based on at least a mini-ITX board with a (dual core?) atom processor, GBit LAN and SATA...
DON'T SHORTEN ANY PINS unless you really know what you do.
Solids LEDs are usually caused by a bad power supply.
So check your power supply first before you brick your device by causing any short...
If you want to access any service from WAN, you have to open the desired ports in the firewall settings, and not disable the firewall completely.
If you do not describe what firmware you use, you...
I never had a time capsule, but my short experience with two WL-500W for tests with as a wireless bridge are not that pleasant.
The encrypted wireless throughput was about 40MBit/sec only, slightly...
.
.
Do you mean Megabyte or Megabit per second?
WAN-LAN or WAN-Wifi or LAN-Wifi traffic?
I think the maximum bandwidth for routed traffic is about 2 MByte/sec on such devices. The LAN-Wifi bridge is...
I think, Teamspeak is distributed as binary packages for the x86 platform only, so it will not run on any other cpu type.
Ist lsdstart ausführbar und in einem Verzeichnis, das in $PATH angeführt ist.
Wenn nein, dann entweder "chmod +x lsdstart" oder lsdstart mit Pfadangabe starten, z. B. ./lsdstart (im aktuellen...
:D:D:D:D
Das nennt sich dann Firefox oder Internet Explorer :D:D
If you fully trust the (encrypted?) authentication mechanism of CTCS, then it's OK to open the port from the internet.
If you don't trust it, use ssh tunnelling only for such purposes, if possible...
My goal is to build a wireless bridge (WPA2 encrypted), bridging a complete vlan trunk with draft-N speeds. I currently have this setup with two foneras running openwrt, but the throughput is only...
Flashen via tftp geht nur über den Firmware Recovery Modus, zu diesem Zeitpunkt ist kein Linux mit WLAN Treiber aktiv, nur der Boot Loader.
Beim älteren WL-500gd wird explizit vom Flashen über das...
You have to configure your routing rules that all traffic goes over the VPN tunnel.
That maybe difficult, if you do not want to route all traffic on the WL-500gp over the VPN tunnel (even the one,...
Transmission supports proxies only for communication with the tracker not for p2p communication.
i. e. you cannot tunnel your p2p traffic with a regular ssh tunnel.
You will need an IP or ethernet...
Welche Version von openwrt?
dnsmasq läuft am wl-700ge? Wahrscheinlich, weil sonst würde dhcp ja auch nicht gehen...
Was sagt der Window Client bei einer DNS Abfrage? Timeout?
http://trac.transmissionbt.com/wiki/man
If you stop downloading/seeding, and your hard disk still spins up, you could stop/terminate the daemon as well.
Do you want to enable or disable spin-down on you disk?
If you are downloading/seeding torrents, every access to the disk disk will cause a spin-up. If you don't like that, stop downloading/seeding...
Am Auto kannst du auch nicht mit einem Knopfdruck die Reifen wechseln, wenn das nicht vom Hersteller vorgesehen ist. Auch ein Kopfstand hilft hier nicht ;-)
Ich empfehle, sich etwas in die...
Die onboard Schnittstellen von diversen Routermodellen sind, abgesehen von der TTL-Spannung, keine vollwertigen RS-232C Schnittstellen, es fehlen alle Steuerleitungen, wie RTS, CTS, DSR, DTR, RI....