Please help me unbrick WL500GPv2
I've got WL-500GPv2 router and by mistake I tried to apply 32MB-RAM patch for v1:
nvram set sdram_init=0x0009
nvram set sdram_ncdl=0
nvram commit
reboot
After that LAN1-LAN4 and WAN LEDs became lit constantly, and router could not be put in recovery mode using standard RESET button technique. I had googled similar cases, and found out that serial console would help. I've tried two variants of serial console adapter - MAX232-based and FT232-based, but there was nothing on the terminal. So I tried to ground pin 9 on flash chip during boot. Since I did the trick, the behaviour of router had changed. Now LAN LEDs is off, WAN LED reflects actual activity, and I can put it in recovery mode with Power LED flashing continuously... but I can't reflash it! No pings to 192.168.1.1, still no activity on serial console, both Linux atftp tool and Windows ASUS firmware restoration utility don't work.
Please tell me what's probably happened with my router? Maybe my serial console doesn't work properly because of wrong soldering etc? Can anyone point me to exact schematic that work? Maybe the last chance to reflash is JTAG? But I couldn't find nor any schematic neither howto on this. Can anyone help me?
1 Attachment(s)
on board power supply problem
Hello there,
My ASUS WL-500gP broke down after storm goes over my house. I identify problem in onboard power supply. I toughed two of chip near to power conector. And these two chips was so hot. Temperatures about 50 degress, I estimate.
I tryed to find tech. spec. in google, but I have no luck.
Can someone of masters help me to solve my problem, please.
on board power supply problem
Quote:
Originally Posted by
wpte
There is no one of capacitors popped.
I will take photo of mine own board tomorrow, and I will upload it.
need help with (almost) bricked wl-500gp (v1)
Hi guys
It's my first post on the forum so please go easy on me :).
I joined the open source world very recently when a colleague of mine from the office gave me the wl-500gp (v1) to use for spare parts in my personal hw projects. I fixed the router and eventually I discovered it's actually a very nice router (especially with custom firmware like openwrt). I even did the ram mod (now the router has 128 MB of ram and used to work ok until I messed it up). Long story cut short: after installing the openwrt whiterussian 0.9 I got so pi**ed off (don't ask why) that I deleted _all_ the nvram settings using the webif (except the hardware_version, pmon_ver, sdram_config, sdram_init, sdram_ncdl and sdram_refresh) - also please don't ask why. Now the router seems to boot up fine (except the power led doesn't go off after the boot loader finishes loading and lights up when the router has finished booting). Both the reset and the restore buttons do not work (actually they work but they are not effective) so I cannot put the router in recovery mode. The power led lights up and the wifi led is off when powering up the router and after some time the wifi led lights up also so the router seems to boot ok but not configure any IP on any interface (wired or wireless) - maybe because I deleted all the MACs from the nvram ? I've got a serial console cable but with different connector (and no matter how pi**ed off I am a female connector cannot be plugged into another female connector :)). Provided that I will change the connector tomorrow and get the console to work ok could you guys please guide me into hacking the CFE and program the nvram settings back ? Also I would need a minimum list of nvram settings which can get the router to work ok (so I know what to write back in my nvram). I have the MACs saved so I only need the other nvram settings and how to do the job using the serial console.
Thank you in advance and sorry for the long post
Problem using my wl-500gp v1
Good day, sorry about the header, I really cant think of any proper title about the problem on the router.
Here's my network setup, 3 computers wired to the wl-500gp, 2 desktops and 1 laptop, before there are no problems but suddenly surfaced recently.
The laptop suddenly is having a hard time connecting to the internet, I checked the LAN icon on taskbar and it says its disconnected, by the way the 2 desktops are connected to the internet, no problems.
By the looks of it, it seems the problem was on the laptop, tried going for a USB to LAN converter but it didn't cut it, still the same problem, changed cables, same problem, until I decided to change the whole router itself.
Purchased a wired router, connected the 3 computers and there are no more problems! The laptop is connected to the internet. All of them working simultaneously.
What I noticed is that, the power supply for the wl-500gp is now hot to touch when connected for about 15mins. I know that power adapters tend to go hot while being used but this one is very hot to touch.
I'm not sure if this is the problem or maybe there are others who experienced this. I just wanna ask for recommendation on what to do with it. Thanks a lot in advance.
My wl500gp v1 is probably bricked
Hi. My router was working fine, then it suddenly stop: I have no lan/wlan access to the router. I can start it in recovery mode, but i get no ping. I tried with asus recovery tool and with tftp, without success.
What can I do now?
Thanks
Dead power supply looks like bricked.
I lost my power supply and got this response. I used an old Zip drive power supply with the right voltage to get up and running. Found a replacement power supply on Amazon.
