Poptop installation

[superkent]

Help. All install from mmX config. But VPN not work. I place log's.

Dec  3 04:17:37 pptpd[233]: CTRL: Client 192.168.15.55 control connection started
Dec  3 04:17:37 pptpd[233]: CTRL: Starting call (launching pppd, opening GRE)
Dec  3 04:17:37 pppd[234]: pppd 2.4.2 started by admin, uid 0
Dec  3 04:17:37 pppd[234]: Using interface ppp0
Dec  3 04:17:37 pppd[234]: Connect: ppp0 <--> /dev/pts/1
Dec  3 04:18:07 pppd[234]: LCP: timeout sending Config-Requests 
Dec  3 04:18:07 pppd[234]: Connection terminated.
Dec  3 04:18:07 pppd[234]: Exit.
Dec  3 04:18:07 pptpd[233]: GRE: read(fd=6,buffer=4205cc,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs
Dec  3 04:18:07 pptpd[233]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7)
Dec  3 04:18:07 pptpd[233]: CTRL: Client 192.168.15.55 control connection finished

When connect, ifconfig no shows ppp0 interface. Why?

br0       Link encap:Ethernet  HWaddr 00:18:F3:93:A7:FD
          inet addr:192.168.15.1  Bcast:192.168.15.255  Mask:255.255.255.0
          inet6 addr: fe80::218:f3ff:fe93:a7fd/10 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4348 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5397 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:460648 (449.8 KiB)  TX bytes:1803374 (1.7 MiB)

eth0      Link encap:Ethernet  HWaddr 00:18:F3:93:A7:FD
          inet6 addr: fe80::218:f3ff:fe93:a7fd/10 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:100515 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5929 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:10184138 (9.7 MiB)  TX bytes:1940298 (1.8 MiB)
          Interrupt:4 Base address:0x1000

eth1      Link encap:Ethernet  HWaddr 00:18:F3:93:A7:FD
          inet6 addr: fe80::218:f3ff:fe93:a7fd/10 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:14
          TX packets:0 errors:90 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:2 Base address:0x2000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING MULTICAST  MTU:16436  Metric:1
          RX packets:1870 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1870 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:160302 (156.5 KiB)  TX bytes:160302 (156.5 KiB)

vlan0     Link encap:Ethernet  HWaddr 00:18:F3:93:A7:FD
          inet6 addr: fe80::218:f3ff:fe93:a7fd/10 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4351 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5399 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:478218 (467.0 KiB)  TX bytes:1825118 (1.7 MiB)

vlan1     Link encap:Ethernet  HWaddr 00:18:F3:93:A7:FD
          inet addr:62.16.2.71  Bcast:62.16.2.255  Mask:255.255.255.0
          inet6 addr: fe80::218:f3ff:fe93:a7fd/10 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:96159 errors:0 dropped:0 overruns:0 frame:0
          TX packets:528 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:7896400 (7.5 MiB)  TX bytes:115032 (112.3 KiB)

in pptpd.conf

localip 192.168.253.1
remoteip 192.168.253.2-3

[mrQQ]

has anyone been able to solve this? i tried running pptpd on tomato, but i have same problems, same error, connecting only 1 time out of 4, and only if i disable encryption..