RT-N10U B is supported by oleg firmware?

[Omega]

Hello. Has anyone tried clkfreq=373, 186, 93 on rt-n10u_b ?
Is the router booting with this value? From your discussion I understood that clkfreq=480,160,80 is a safe setting, but I want either:

373, 186, 93 or 400, 200, 100 in order to preserve CPU / RAM / FSB ratio.

I belive someone (Hohmach: 'C clkfreq=400,200,100 ðîóòåð ïîñëå ïåðåçàãðóçêè çàâèñ, ïîñëå ïåðåäåðãèâàíèÿ ïèòàíèÿ áðèêíóëñÿ.')
said that clkfreq=400,200,100 bricked his router, but I don't understand too well through Google Translate.

Thanks.

There is a question about the RT-N12

Tried overclocking nvram set clkfreq=480,160,80 at RT-N12 (300,150,75). Works, but unstable, kernel swears off wifi.
C clkfreq=400,200,100 router after the reboot hangs, after the distortion of the power brick. Took replaced by RT-N12B1

http://wl500g.info/showthread.php?t=...42639&langid=3

I tried to upgrade its memory to 64Mb, I did set sdram_init from 0x0419 to 0x0c19/0x0c29/0x0113
along with (or without) manual_boot_nv=1, but it was always reporting 32Mb.

What is odd is that after setting sdram_ncdl to 0x0000, it does not get recalculated after reboot,
remaining 0, therefore I believe it doesn't use these nvram settings.

I did manage to (stable) 'clkfreq' overclock it to:
354,177,88 / 373,186,93 / 400,200,100 but it gets quite hot even after radiator replacement.
I would recommend 354,177,88 with stock radiator to have it running for years.

http://www.dd-wrt.com/phpBB2/viewtop...52672&start=15

ASUS RT-N10U

FCC ID: MSQRTN10U

• CPU1: Broadcom BCM5356U (300Mhz)
• RAM1: 32MB (EMST M13S2561616A-5T)
• FLA1: 8MB (Winbond 25Q64BV)

ASUS RT-N10U B

FCC ID: MSQRTN10UB

• CPU1: Broadcom BCM5356U (300MHz)
• RAM1: 32 MB (Winbond W9425GJH-5)
• FLA1: 8 MB (Macronix MX25L6406E)

Mod RAM 64MB

• 32MB DDR SDRAM 16bit -> EtronTech EM6AA160TSA-5G (Winbond W9425GJH-5)
• 64MB DDR SDRAM 16bit -> VDATA VDD9616A8A-5C (0x105/0x106/0x107)

nvram set sdram_init=0x0419
nvram set sdram_config=0x107
nvram set sdram_ncdl=0
nvram commit
reboot

Overclocking RT-10U(B)

# default
clkfreq=300,150,75

# +25%
nvram set clkfreq=500,200,100
nvram commit
reboot

# +8%
nvram set clkfreq=480,160,80
nvram commit
reboot

#Log
Jan 1 04:00:02 kernel: CPU: BCM5357 rev 1 at 480 MHz
Jan 1 04:00:02 kernel: Using 240.000 MHz high precision timer

#CPU Info
system type : Broadcom BCM5357 chip rev 1 pkg 8
processor : 0
cpu model : MIPS 74K V4.9
BogoMIPS : 239.10

http://wl500g.info/showthread.php?t=...107#post246107