[HowTo] Install and configure Oleg's firmware

[tmsulica]

Hello wengi , great tutorial i say again. I have followed your tutorial about 2 or 3 years ago when added on my wl500-gp oleg's latest firmware and now, about a week or two latest enthusiast firmware. So i thank you for your great tutorial.

Now my questions:

I have an HSPDA modem, ZTE MF100 from my provider DIGI. I found in the web interface a part where i can set-up a 3g modem. I managed to find correct settings for my provider, and finally after some hours of testing finally works. But when i look at my sistem log i found many errors ... this is my log :

Jan  1 02:00:27 kernel: sda: Write Protect is off
Jan  1 02:00:27 kernel:  /dev/scsi/host0/bus0/target0/lun0: I/O error: dev 08:00, sector 0
Jan  1 02:00:27 kernel:  I/O error: dev 08:00, sector 0
Jan  1 02:00:27 kernel: sda: Waiting for disc 0 to settle.
Jan  1 02:00:30 kernel: sda: Unit Not Ready, sense:
Jan  1 02:00:30 kernel: Info fld=0x0, Current 00:00: sns = f0  2
Jan  1 02:00:30 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:30 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:30 kernel: sda : READ CAPACITY failed.
Jan  1 02:00:30 kernel: sda : status = 1, message = 00, host = 0, driver = 08 
Jan  1 02:00:30 kernel: Info fld=0x0, Current sd00:00: sns = f0  2
Jan  1 02:00:30 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:30 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:30 kernel: sda : block size assumed to be 512 bytes, disk size 1GB.  
Jan  1 02:00:30 kernel: sda: Write Protect is off
Jan  1 02:00:30 kernel:  /dev/scsi/host0/bus0/target0/lun0: I/O error: dev 08:00, sector 0
Jan  1 02:00:30 kernel:  I/O error: dev 08:00, sector 0
Jan  1 02:00:30 kernel: sda: Waiting for disc 0 to settle.
Jan  1 02:00:33 kernel: sda: Unit Not Ready, sense:
Jan  1 02:00:33 kernel: Info fld=0x0, Current 00:00: sns = f0  2
Jan  1 02:00:33 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:33 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:33 kernel: sda : READ CAPACITY failed.
Jan  1 02:00:33 kernel: sda : status = 1, message = 00, host = 0, driver = 08 
Jan  1 02:00:33 kernel: Info fld=0x0, Current sd00:00: sns = f0  2
Jan  1 02:00:33 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:33 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:33 kernel: sda : block size assumed to be 512 bytes, disk size 1GB.  
Jan  1 02:00:34 kernel: sda: Write Protect is off
Jan  1 02:00:34 kernel:  /dev/scsi/host0/bus0/target0/lun0: I/O error: dev 08:00, sector 0
Jan  1 02:00:34 kernel:  I/O error: dev 08:00, sector 0
Jan  1 02:00:34 kernel: sda: Waiting for disc 0 to settle.
Jan  1 02:00:36 kernel: sda: Unit Not Ready, sense:
Jan  1 02:00:36 kernel: Info fld=0x0, Current 00:00: sns = f0  2
Jan  1 02:00:36 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:36 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:37 kernel: sda : READ CAPACITY failed.
Jan  1 02:00:37 kernel: sda : status = 1, message = 00, host = 0, driver = 08 
Jan  1 02:00:37 kernel: Info fld=0x0, Current sd00:00: sns = f0  2
Jan  1 02:00:37 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:37 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:37 kernel: sda : block size assumed to be 512 bytes, disk size 1GB.  
Jan  1 02:00:37 kernel: sda: Write Protect is off
Jan  1 02:00:37 kernel:  /dev/scsi/host0/bus0/target0/lun0: I/O error: dev 08:00, sector 0
Jan  1 02:00:37 kernel:  I/O error: dev 08:00, sector 0
Jan  1 02:00:37 kernel: sda: Waiting for disc 0 to settle.
Jan  1 02:00:39 kernel: sda: Unit Not Ready, sense:
Jan  1 02:00:39 kernel: Info fld=0x0, Current 00:00: sns = f0  2
Jan  1 02:00:39 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:39 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:40 kernel: sda : READ CAPACITY failed.
Jan  1 02:00:40 kernel: sda : status = 1, message = 00, host = 0, driver = 08 
Jan  1 02:00:40 kernel: Info fld=0x0, Current sd00:00: sns = f0  2
Jan  1 02:00:40 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:40 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:40 kernel: sda : block size assumed to be 512 bytes, disk size 1GB.  
Jan  1 02:00:40 kernel: sda: Write Protect is off
Jan  1 02:00:40 kernel:  /dev/scsi/host0/bus0/target0/lun0: I/O error: dev 08:00, sector 0
Jan  1 02:00:40 kernel:  I/O error: dev 08:00, sector 0
Jan  1 02:00:40 kernel: sda: Waiting for disc 0 to settle.
Jan  1 02:00:42 kernel: sda: Unit Not Ready, sense:
Jan  1 02:00:42 kernel: Info fld=0x0, Current 00:00: sns = f0  2
Jan  1 02:00:42 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:42 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:43 kernel: sda : READ CAPACITY failed.
Jan  1 02:00:43 kernel: sda : status = 1, message = 00, host = 0, driver = 08 
Jan  1 02:00:43 kernel: Info fld=0x0, Current sd00:00: sns = f0  2
Jan  1 02:00:43 kernel: ASC=3a ASCQ= 0
Jan  1 02:00:43 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
Jan  1 02:00:43 kernel: sda : block size assumed to be 512 bytes, disk size 1GB.  
Jan  1 02:00:43 kernel: sda: Write Protect is off
Jan  1 02:00:43 kernel:  /dev/scsi/host0/bus0/target0/lun0: I/O error: dev 08:00, sector 0
Jan  1 02:00:43 kernel:  I/O error: dev 08:00, sector 0
Jan  1 02:00:43 kernel:  unable to read partition table
Jan  1 02:00:43 kernel:  I/O error: dev 08:00, sector 0
Mar 11 21:39:02 pppd[159]: System time change detected.
Mar 11 21:39:21 ntp client: Synchronizing time with pool.ntp.org...

.

My HSPDA MODEM is an ZTE MF 100 @ 3,2 Mbs. The modem has an micro sd reader and an virtual drive with drivers for windows. Should i worry about those errors?. It would trouble my hdd when i will plug it in ?? ( I followed your tutorial, installed HDD, installed all till Transmission, but i conect the hdd only when i want to download torrents, and works fine , no errors - without my hdd ).

And second one: I normally use an PPOE Lan conection but i want to use my ZTE Modem only as a backup when the network fails. I understanded that the koppel version of oleg's firmware does that, my 1.9.2.7-d-r2624 release can do that ?

Or at least to make a script or something when my PPOE conexion is dead, and i insert my usb 3G modem to switch the connection automatically from PPOE to USB Modem. I saw that on the web interface at 3G/CDMA Modem tab, at additional parameters i have an device initial script tab. And if an script exists can it be flashed on my router so i do not have to plug my hdd for that ?

It would be an ideea to have my 3g modem ready, and when my ppoe conexion is dead i just plug in my modem and the router does the rest.....


10x and waiting your answer ....


BTW: My settings for my 3G modem to work are:
- zero cd configuration: Auto ("Not set" is not showing errors, starts the drivers but at USB location ID i don't see any modem installed)
- username: user
- password : user
- APN : internet
- Dial number: *99#
- Call on demand: Yes
- USB Device location ID 1.3 (as seen in View window, tts/2 )
- Autodetect device: Yes
- Usb device & product id as detected
- Usb device packet size : 0
- Usb device serial speed: 11200
(this values i founded on an local forum with settings for koppel 1.71 , here http://craciun.in/?p=111 )