[HowTo] Install and configure Oleg's firmware

[none]

Thank a lot for your answer!

I have the firmware 1.9.7.2-8, but ( )

in "IP Config", I don't have only "LAN"
it is actually "WAN & LAN"

so I suppose it is what you meant...
so then, in "WAN & LAN" I don't use WAN, so the only thing I can configure are:
->Host Name
->Ip Address
->Subnet Mask


no "default gateway"

I am lost... sniff!


EDIT: by the way, I have a WL500g Premium, maybe that is the problem?

[wengi]

Hi,

Just to get it right: The asus is connected to a modem and acts as router or do you have another router doing the internet stuff?

wengi

[accsi]

HI!

I'm newbie. I can't download IPKG Packet .
wget http://ipkg.nslu2-linux.org/feeds/op...-12_mipsel.ipk
gives a message:
wget: server returned error 404: HTTP/1.1 404 Not Found

What's the problem? What make I wrong?

Thanks
accsi

[wengi]

Hi,

as mentioned in the german thread:
http://ipkg.nslu2-linux.org/ is not reachable atm.

Not your fault. Just wait.

wengi

EDIT: Updated HowTo due to new version of uclib.

[none]

Thank you for your answer Wengi!
Sorry for the delay, I was sick...

To answer your question, my asus is connected to a modem-router that does everything concerning internet.

Does it answer your question?

Thanks again for your help!

[wengi]

Hi,

i think you operation mode is the wrong one.

Do the following:

- Make sure that webinterface -> System Setup -> Operation Mode is set to "Access Point"
- Make sure that webinterface -> IP Config -> LAN is set correctly corresponding to your network/router.

wengi

[alex.bumbacea]

this firmware can be user with download master?
LE: *used

[wengi]

Hi,

no, the oleg firmware does not include the download master.
(If this was your question, 'cause it is not that clear)

wengi

[calebz]

DM wont work on oleg.
You need transmission to download torrents.
Its better than DM but you need to put some time into configuration

[alex.bumbacea]

thx for your answers.
Now i have another :-s, i hope u don't mind.
Let's say i wanna use my router as torret client, lamp server and , of course, as a router. i would like to know if it has the power to do so much, and if it does, please tell me an aprox. number of torrents that i should let active in the same tine in the transmission conf.
LE: I managed to install a lamp, but i can not acces my web server from net.
In lan i have 192.168.10.0/24. I made PF from 80->192.168.10.1:8080. I can acces it from inside my net home with the public ip, but when somebody else try to access it, there si no answer. Any idea?

[alex.bumbacea]

I'm back with another problem:
Now i have a seccond net connection and woul like to pass imap/browsing trough one, and all what means torrents/dc++ trough the second(this is one with larger metro bandwith).
Can i doit with this router? And if someone knows any tutorial for this... please pot it...

[wengi]

I'm back with another problem:
Now i have a seccond net connection and woul like to pass imap/browsing trough one, and all what means torrents/dc++ trough the second(this is one with larger metro bandwith).
Can i doit with this router? And if someone knows any tutorial for this... please pot it...

This depends on what you want to do and is mainly a routing problem. I would suggest opening a new thread for this.
We also need more informations:

- How are the connections realized?
- How is your subent setp? Has asus 2 IPs?
- Is imap/browsing outgoing or incoming?
- Torrent is running on your router?

And so on....

wengi

[piezomotor]

I had one USB HD connected to my WL500gP, now I have two:

/dev/scsi/host0/bus0/target0/lun0/part1 151705660 41080112 102919340 29% /opt
/dev/scsi/host1/bus0/target0/lun0/part1 976521536 84110528 892411008 9% /tmp/mnt

Sometimes they will swap-

/dev/scsi/host0/bus0/target0/lun0/part1 151705660 41080112 102919340 29% /tmp/mnt
/dev/scsi/host1/bus0/target0/lun0/part1 976521536 84110528 892411008 9% /opt

How this can be prevented?

Thanks.

[gixie]

I was following the tutorial (btw, exquisite job man, congrats - I'm a linux noob and I could follow it with no problem at all...until this one) and when I was about to install transmission I got the following error
[admin@(none) root]$ ipkg install logrotate
Installing logrotate (3.7.1-4) to /opt/...
Downloading http://ipkg.nslu2-linux.org/feeds/op...1-4_mipsel.ipk
wget: ipkg.nslu2-linux.org: Unknown host
Nothing to be done
An error ocurred, return value: 22.
Collected errors:
ipkg_download: ERROR: Command failed with return value 1: `wget -q -P /opt/ipkg-o1GRVF http://ipkg.nslu2-linux.org/feeds/op...1-4_mipsel.ipk'
Failed to download logrotate. Perhaps you need to run 'ipkg update'?
I would like to know if there's something that I can do... To me it looks like there's a problem with the website where wget gets everything. I am writing from the same station, so internet's working fine...
Please advise...

[wengi]

Hi,

you are right.
This was an error with the website. (http://ipkg.nslu2-linux.org/feeds/op.../cross/stable/)
But it is working here.

Try again.

@piezomotor

Just quick and dirty:
Create a file on one HDD (e.g. hdd1.tmp)
Check if this file exists after mount. If not: unmount and mount the other hdd.
This is not a good solution but it should work. I remeber that i read about this prob in the forums. Do a search.

wengi