У меня WL-500Gp, залита прошивка Олега. Так мне гуглить по robocfg? На форуме ничего путного (а главное конкретного) найти не удалось :-(Где взять подробное описание robocfg (желательно на русском)?
unimozg, можно просто указать маску 255.255.254.0 на роутере и всех компах в lan1-lan2.
kazak_vmik, у тебя тоже 700ge? Про него ничего сказать немогу. А прошивке Олега можно сделать любой из портов или группы портов LAN отдельным интерфейсом со всеми вытекающими (поиск по robocfg)
У меня WL-500Gp, залита прошивка Олега. Так мне гуглить по robocfg? На форуме ничего путного (а главное конкретного) найти не удалось :-(Где взять подробное описание robocfg (желательно на русском)?
Last edited by kazak_vmik; 24-07-2007 at 21:03.
Ну какже, в инструкции по настройки с нуля в 13-ом пункте про robocfg рассказывается. http://wl500g.info/showpost.php?p=20276&postcount=3
robocfg --help
А на русском информация я думаю что только на этом форуме есть, т.к. автор программы Олег.
з.ы. Я думаю эта более подходящая тема для обсуждения wl500gp с прошивкой от Олега http://wl500g.info/showthread.php?t=8056
Last edited by Mam(O)n; 24-07-2007 at 22:00.
Приобрёл два месяца назад мегадевайс ASUS WL-700gE
в сети провайдер раздаёт инет через VPN.
настроил на маршрутизаторе интернет через PPTP- всё замечательно работало. Но неделю назад провайдер чегото сделал с серверами и PPTP неподнимается, в логе пишется следующее
Изза этого пришлось на маршрутизаторе настроить Static IP, а VPN поднимать с компьютера. При наличии дома двух компьютеров это очень неудобно. Провайдер помогать отказывается- мол на компютере всё работает, а маршрутизаторы мы ненастраиваем...Jul 25 16:44:26 pppd[1179]: Using interface ppp0
Jul 25 16:44:26 pppd[1179]: local IP address 10.64.64.64
Jul 25 16:44:26 pppd[1179]: remote IP address 10.112.112.112
Jul 25 16:44:26 pppd[1179]: Starting link
Jul 25 16:44:26 pppd[1179]: Serial connection established.
Jul 25 16:44:26 pppd[1179]: Connect: ppp0 <--> /dev/pts/0
Jul 25 16:44:41 pptp[1186]: warn[connect_timeoutptp_callmgr.c:359]: connect timeout for 15 seconds
Jul 25 16:44:41 pptp[1186]: warn[open_inetsockptp_callmgr.c:391]: connect: Operation now in progress
Jul 25 16:44:41 pptp[1186]: fatal[callmgr_mainptp_callmgr.c:134]: Could not open control connection to 192.168.1.2
Jul 25 16:44:41 pptp[1184]: fatal[open_callmgrptp.c:361]: Call manager exited with error 256
Jul 25 16:44:41 pppd[1179]: Modem hangup
Jul 25 16:44:41 pppd[1179]: Connection terminated.
Jul 25 16:45:12 pppd[1179]: Starting link
Jul 25 16:45:12 pppd[1179]: Serial connection established.
Jul 25 16:45:12 pppd[1179]: Connect: ppp0 <--> /dev/pts/0
Jul 25 16:45:27 pptp[1211]: warn[connect_timeoutptp_callmgr.c:359]: connect timeout for 15 seconds
Jul 25 16:45:27 pptp[1211]: warn[open_inetsockptp_callmgr.c:391]: connect: Operation now in progress
Jul 25 16:45:27 pptp[1211]: fatal[callmgr_mainptp_callmgr.c:134]: Could not open control connection to 192.168.1.2
Jul 25 16:45:27 pptp[1210]: fatal[open_callmgrptp.c:361]: Call manager exited with error 256
Jul 25 16:45:27 pppd[1179]: Modem hangup
Jul 25 16:45:27 pppd[1179]: Connection terminated.
Jul 25 16:45:57 pppd[1179]: Starting link
Jul 25 16:45:58 pppd[1179]: Serial connection established.
Jul 25 16:45:58 pppd[1179]: Connect: ppp0 <--> /dev/pts/0
Jul 25 16:46:13 pptp[1240]: warn[connect_timeoutptp_callmgr.c:359]: connect timeout for 15 seconds
Jul 25 16:46:13 pptp[1240]: warn[open_inetsockptp_callmgr.c:391]: connect: Operation now in progress
Jul 25 16:46:13 pptp[1240]: fatal[callmgr_mainptp_callmgr.c:134]: Could not open control connection to 192.168.1.2
Jul 25 16:46:13 pptp[1238]: fatal[open_callmgrptp.c:361]: Call manager exited with error 256
Jul 25 16:46:13 pppd[1179]: Modem hangup
Jul 25 16:46:13 pppd[1179]: Connection terminated.
Помогите настроить аппарат пожалуйста
Посмотри тут, может найдешь настройки для своего провайдера, краем уха слышал что возможны какие то геморы с TTL, поищи на форуме, может то, а может и я чет путаю.
The Russian forums mainly related to wl-500, there is not russian wl-700 forums around. All my topics of wl-700 lost in wl-500 and oleg firmware flames...
So what about your PPTP problem? TTL restrictions?
P.S. BTW, i don't think someone missed the question afer reading ENGLISH log:
Jul 25 16:45:57 pppd[1179]: Starting link
Jul 25 16:45:58 pppd[1179]: Serial connection established.
Jul 25 16:45:58 pppd[1179]: Connect: ppp0 <--> /dev/pts/0
Jul 25 16:46:13 pptp[1240]: warn[connect_timeoutptp_callmgr.c:359]: connect timeout for 15 seconds
Jul 25 16:46:13 pptp[1240]: warn[open_inetsockptp_callmgr.c:391]: connect: Operation now in progress
Jul 25 16:46:13 pptp[1240]: fatal[callmgr_mainptp_callmgr.c:134]: Could not open control connection to 192.168.1.2
Jul 25 16:46:13 pptp[1238]: fatal[open_callmgrptp.c:361]: Call manager exited with error 256
Jul 25 16:46:13 pppd[1179]: Modem hangup
Jul 25 16:46:13 pppd[1179]: Connection terminated.
Last edited by mawr; 03-08-2007 at 12:41.
Помогите кто разбирается.Подключил его к консоли и замкнул 9 и 10 пин рядом с процом.Вот что пишет CFE
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: ?| 12¤e 29 20:36:58 CST 2005 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
CPU type 0x29006: 264MHz
Total memory: 67108864 KBytes
Total memory used by CFE: 0x80800000 - 0x8089BA00 (637440)
Initialized Data: 0x80831B70 - 0x80834250 (9952)
BSS Area: 0x80834250 - 0x80835A00 (6064)
Local Heap: 0x80835A00 - 0x80899A00 (409600)
Stack Area: 0x80899A00 - 0x8089BA00 (8192)
Text (code) segment: 0x80800000 - 0x80831B70 (203632)
Boot area (physical): 0x0089C000 - 0x008DC000
Relocation Factor: I:00000000 - D:00000000
Device eth0: hwaddr 00-18-F3-73-9E-2D, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Null Restore Flag.
set pivot_wait = 0
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ..... 2723840 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
CPU revision is: 00029006
Primary instruction cache 16kb, linesize 16 bytes (2 ways)
Primary data cache 16kb, linesize 16 bytes (2 ways)
Linux version 2.4.20 (root@localhost.localdomain) (gcc version 3.0 20010422 (pre
release) with bcm4710a0 modifications) #212 Wed Aug 30 16:57:52 CST 2006
BCM47XX ChipID = 0x4704, RevisionID = 8, Options = 0x2
Setting GPIO 3 to output of 1.
Setting GPIO 6 to output of 1.
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
CPU: BCM4704 rev 8 at 264 MHz
Calibrating delay loop... 263.78 BogoMIPS
Memory: 61896k/65536k available (2424k kernel code, 3640k reserved, 132k data, 8
4k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 byte
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting ks
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver v1.1.22 [Flags: R/O]
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-bit.o: i2c bit algorithm module
i2c-proc.o version 2.6.1 (20010825)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI en
abled
ttyS00 at 0xb8000300 (i
ttyS01 at 0xb8000400 (irq = 0) is a 16550A
Generic MIPS RTC Driver v1.0
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AEC6265: IDE controller on PCI bus 01 dev 10
PCI: Enabling device 01:02.0 (0000 -> 0003)
AEC6265: chipset revision 16
AEC6265: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AEC6265: ROM disabled at 0x00000000
ide2: BM-DMA at 0x0180-0x0187,
ide3: BM-DMA at 0x0188-0x018f, BIOS settings: hdgio, hdhio
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Amd/Fujitsu Extended Query Table v1.0 at 0x0040
Physically mapped flash: JEDEC Device ID is 0xC4. Assuming broken CFI table.
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Flash device: 0x200000
Physically mapped flash: cramfs filesystem found at block 1410
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x001f0000 : "linux"
0x00160b04-0x001f0000 : "rootfs"
0x001f0000-0x00200000 : "nvram"
sflash: found no supported devices
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 01:03.2 (0000 -> 0002)
ehci_hcd 01:03.2: PCI device 1106:3104
ehci_hcd 01:03.2: irq 2, pci mem c000d000
usb.c: new USB bus registered, assigned b
ECHI PCI device 31041106 found.
ECHI reg 0x49 = 80242720
ECHI reg 0x49 changed to = 80242700
ECHI reg 0x4b = 80242709
ECHI reg 0x4b changed to = 80242729
PCI: 01:03.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correctin
g to 32
ehci_hcd 01:03.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
new device strings: Mfr=3, Product=2, SerialNumber=1<6>hub.c: USB hub found
hub.c: 4 ports detected
host/usb-uhci.c: $Revision: 1.275 $ time 16:59:10 Aug 30 2006
host/usb-uhci.c: High bandwidth mode enabled
PCI: Enabling device 01:03.0 (0000 -> 0001)
ECHI PCI device 30381106 found.
UCHI reg 0x41 = 10
UCHI reg 0x41 changed to = 0
host/usb-uhci.c: USB UHCI at I/O 0x200, IRQ 2
host/usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
new device strings: Mfr=0, Product=2, SerialNumber=1<6>hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 01:03.1 (0000 -> 0001)
ECHI PCI device 30381106 found.
UCHI reg 0x41 = 10
UCHI reg 0x41 changed to = 0
host/usb-uhci.c: USB UHCI at I/O 0x220
host/usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
new device strings: Mfr=0, Product=2, SerialNumber=1<6>hub.c: USB hub found
hub.c: 2 ports detected
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
host/usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
host/usb-ohci.c: usb-00:03.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 4
new device strings: Mfr=0, Product=2, SerialNumber=1<6>hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Skipping autodetection of RAID arrays.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5
pivot_rc starting...
pivot_rc proceeding to boot from disk...
ERROR(a):mount_pivot_point failed to mount location : /dev/ide/host2/bus0/target
0/lun0/part1...
ERROR(b):mount_pivot_point error : No such file or directory...
pivot_rc boot loop error for location 0...
ERROR(a):mount_pivot_point failed to mount location : /dev/ide/host2/bus0/target
0/lun0/part2...
ERROR(b):mount_pivot_point error : No such file or directory...
pivot_rc boot loop error for location 1...
pivot_rc did not boot -> hang wait for network loading...
Using /lib/modules/2.4.20/kernel/drivers/net/et/et.o
Symbol version prefix ''
Warning: loading /lib/modules/2.4.20/kernel/drivers/net/et/et.o will taint the k
ernel: no license
See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.39.0
Module et loaded, with warnings
vlan0: No such device
eth1: No such device
eth0: No such process
Waiting for new image on IP 192.168.1.1.
Waiting for announcement from download server...
tftp не работает и telnet Тоже не коннектит.Жму ctrl+c безрезультатно
Last edited by Amlet1; 06-10-2007 at 12:36.
Все, до перепрашивался, блин...
Был Asus WL-700gE с последней родной его прошивкой (1.0.7.8)
я его перепрошил openwrt, прошивку взял с http://wl700g.homelinux.net/drupal/?q=node/24
но "change root to hdd" не сделал, зайдя по telnet роутер стал виснуть, то есть я даже недобился ls -la и я его перегрузил, теперь он молчит
не каких ping 192.168.1.1 и т.д.
на роутере горит READY и сетевой порт в которые подключен комп (192.168.1.11)
RESET не помог
что теперь? в помойку?
arp -s 192.168.1.100 его_мак так же результатов не дало
Last edited by georglk; 05-01-2008 at 20:20.