Also, I've added tips and tricks section here . Read them also.
Download files@chupa here:
firmware
rootfs
Sources for building
New firmware which contains bugfixes for the following problems:
- WebCam, Ftp, Samba server does not work in 1.7.5.9-1 due to several incompatibilities between official/custom firmwares
- DNS proxy rejects queries after PPPoE/PPTP reconnection
- Custom firmware configuration for the WAN iface was not set in PPPoE mode
available for download.
Rootfs and sources are available here.
Last edited by Oleg; 19-06-2004 at 18:05.
Also, I've added tips and tricks section here . Read them also.
Last edited by Oleg; 19-06-2004 at 18:24.
okay webcam and ftp is working! thx oleg!
The problem with VPN connections also seems to be fixed.
Any clue about what was wrong?
I've no idea. The only thing which is relevant is the DNS, but that's looks strange.
Just one question?
Which stuff is better to place in pre-boot script, and which in post-boot??
And one more choice is to modify /usr/local/init/functions
Could give me some tips?
THX
Pipos (2xWL-500g, WDS-only mode, used as backbone for MAN network; 1xWL-500g in Client Mode with NAT)
The Afina one still doesn't work with CR2, but the Logitech one now works. Thanks.
BTW the webcam capability never works on me when connecting from Internet, for either the official firmware or the hacked ones (garbage text code was shown instead). Any idea?
I installed 1.7.5.9-2 and followed Oleg's instructions how to change the smb.conf file. I changed the working group so I see the share in my network. However I cannot write to this share. After loading the samba drivers also i am prohibited to upload to the USB dongle via FTP.
Another question I have; I added some commands in the post-boot file, however I have the feeling the commands are not executed sequencially, I think the commands are executed in parallel. When I combine the commands in a single script and execute the script from the post-boot file everything works fine.
use the search, a workaround is availableOriginally Posted by geoffreytw
and you can not connect to the data port for viewing your webcam (unless your are able to read data )
My little Asus Collection: Too much to fit inhere, my 2 babies:WL500w 1.9.2.7-10(OLEG) VX2SE Yellow Lamborghini notebook
WL500g Forum Asus Files OpenDir
Asusforum.NL -- Asusforum.DE -- Asusforum.RU -- Asusforum.PL -- Asusforum.NET -- Asusforum.EU -- Asusforum.BE -- Asusforum.ES -- Asusforum.INFO
Did anyone have the client mode working in this firm.
I'm struggeling for some time now. I'm trying to connect to a linksys WRT54G
net setup
ADSL (192.168.1.254) - Linksys (192.168.0.1)-Asus(client mode 192.168.0.10) - PC (192.168.0.30)
I used nvram set 13_x_ClientMode=1 + commit.
In terminal I do a
route add default gw 192.168.0.1 eth2
and a echo 1 > /proc/sys/net/ipv4/ip_forward
After that I can ping the AP from the ASUS, and have from the asus box connections to the net
Now, when I try to connect from my PC, I cannot ping the linksys, not any other ip (exept the asus). So somehow the Asus does not forward my requests.
Suggestios, am I'm forgetting something?
That's not correct setting. You should change the IP address of your PC to different subnet otherwise routing can't work (I suppose you have the same mask for all interfaces 255.255.255.0). Try 192.168.2.x.Originally Posted by erik_bies
Also check the gateway settings - ASUS needs to be set as default gateway for your PC.
You don't need to set the routing using Telnet anymore. Just change WAN parameters in web configurator - please note the WAN interface is exchanged with WLAN in Client mode. It works fine including DHCP support - it is possible to perform release / renew online.route add default gw 192.168.0.1 eth2
and a echo 1 > /proc/sys/net/ipv4/ip_forward
Last edited by Technik; 26-06-2004 at 16:29.
Did you use share$ for writing?Originally Posted by bramfm
No they're working just like other scripts - synchronously, unless you've specified " & " at the end of the each command.After loading the samba drivers also i am prohibited to upload to the USB dongle via FTP.
Another question I have; I added some commands in the post-boot file, however I have the feeling the commands are not executed sequencially, I think the commands are executed in parallel. When I combine the commands in a single script and execute the script from the post-boot file everything works fine.
Seems you're trying to setup this in bridging mode (no routing, etc). You should then switch wl500g to access point mode in addition to activating client mode. No other manual modifications required.Originally Posted by erik_bies
Hi.
My printer works om 1.7.5.9, but not on the r2.
But my ADSL only works om r2...
Can these be combined???