WL500g 2 USB Drucker und ein LPT

[Trebron]

Ich sitze gerade vor dem Problem ein zweiten USB-Drucker zu aktivieren.
1 USB und 1 LPT ist kein Problem nur der 2te USB macht Probleme.

Konfiguration: LPT HP970cxi, USB Brother 2030, neu USB Brother 3240c

Drucken kann ich nur noch über RAW Port 9100, weder 9100 noch 9102 geht, wer hat eine Idee?

Auszug aus dem Ausdruck mit "dmesg":

Jan 1 01:00:05 kernel: usb.c: registered new driver usbdevfs
Jan 1 01:00:05 kernel: usb.c: registered new driver hub
Jan 1 01:00:05 kernel: usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
Jan 1 01:00:05 kernel: usb-ohci.c: usb-00:04.0, PCI device 14e4:4715
Jan 1 01:00:05 kernel: usb.c: new USB bus registered, assigned bus number 1
Jan 1 01:00:05 kernel: hub.c: USB hub found
Jan 1 01:00:05 kernel: hub.c: 2 ports detected
Jan 1 01:00:06 kernel: hub.c: new USB device 00:04.0-1, assigned address 2
Jan 1 01:00:06 kernel: hub.c: USB hub found
Jan 1 01:00:06 kernel: hub.c: 4 ports detected
Jan 1 01:00:06 kernel: hub.c: new USB device 00:04.0-1.2, assigned address 3
Jan 1 01:00:06 kernel: lp0: using parport0 (polling).
Jan 1 01:00:06 kernel: usb.c: USB device 3 (vend/prod 0x4cf/0x8818) is not claimed by any active driver.
Jan 1 01:00:07 kernel: usb.c: registered new driver usblp
Jan 1 01:00:07 kernel: printer.c: v0.13: USB Printer Device Class driver
Jan 1 01:00:07 kernel: hub.c: new USB device 00:04.0-1.3, assigned address 4
Jan 1 01:00:07 kernel: printer.c: usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0027
Jan 1 01:00:07 kernel: printer.c: usblp0 Device ID string [57]='MFG:Brother;CMD:PJL,HBP;MDL:HL-2030 series;CLS:PRINTER;'
Jan 1 01:00:08 kernel: hub.c: new USB device 00:04.0-1.4, assigned address 5
Jan 1 01:00:08 kernel: printer.c: usblp1: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0173
Jan 1 01:00:08 kernel: printer.c: usblp1 Device ID string [54]='MFG:Brother;CMD:HBP,BRPJL;MDL:MFC-3240C;CLS:PRINTER;'
Jan 1 01:00:10 kernel: usb.c: registered new driver audio
Jan 1 01:00:10 kernel: audio.c: v1.0.0:USB Audio Class driver
Jan 1 01:00:10 kernel: Linux video capture interface: v1.00
Jan 1 01:00:11 kernel: SCSI subsystem driver Revision: 1.00
Jan 1 01:00:12 kernel: Initializing USB Mass Storage driver...
Jan 1 01:00:12 kernel: usb.c: registered new driver usb-storage
Jan 1 01:00:12 kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan 1 01:00:12 kernel: Vendor: TOSHIBA Model: MK1016GAP Rev: U1.1
Jan 1 01:00:12 kernel: Type: Direct-Access ANSI SCSI revision: 02
Jan 1 01:00:12 kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Jan 1 01:00:12 kernel: SCSI device sda: 19640880 512-byte hdwr sectors (10056 MB)
Jan 1 01:00:12 kernel: Partition check:
Jan 1 01:00:12 kernel: p1
Jan 1 01:00:12 kernel: USB Mass Storage support registered.
Jan 1 01:00:13 pppd[83]: Plugin rp-pppoe.so loaded.
Jan 1 01:00:13 pppd[83]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
Jan 1 01:00:13 pppd[84]: pppd 2.4.2 started by admin, uid 0
Jan 1 01:00:14 kernel: lp driver: get device ID

Trebron

[Trebron]

Problem gelöst!

---
USB > RAW9100 works with Brother MFC-3240c

---
nach der Eingabe von
/usr/sbin/p910nd -f /dev/usb/lp1 2
geht der zweite USB-Drucker

USB > RAW9102 works with Brother HL2030

---
LPT > RAW9101 works with HP 970cxi

INFO:
Die Reihenfolge der USB-Druckerkabel im externen USB-HUB war bei mir das Problem. Der Brother MFC-3240c als Standarddrucker sollte zuerst erkannt werden dann erst der Brother HL2030. LPT Drucker ist immer RAW-Port9101

Trebron