Page 2 of 2 FirstFirst 12
Results 16 to 27 of 27

Thread: Asus RT-N53

  1. #16
    Камрады! А по RT-N53U отдельной ветки нет чтоль? Я чет не нашел. Плохо искал? А то вчера прошу Асусы выложили
    ftр://ftp.asus.com.tw/pub/ASUS/wireless/RT-N53/FW_RT_N53_3004130.zip даю пока здесь. Сорцы зажали
    Last edited by Omega; 19-05-2012 at 20:46. Reason: темы по RT-N53U нет, т.к. такой модели нет :) а по RT-N53 есть, туда и перенесен пост ;)
    Asus RT-N56U firmware: RT-N56U 3.4.3.7-072 DLNA build
    Asus RT-N12U firmware: 1.9.2.7-rtn-r4454
    Asus RT-N65U firmware: RT-N65U 3.0.3.7-072

  2. #17
    Join Date
    Mar 2009
    Location
    Russia, Moscow
    Posts
    2,112
    Blog Entries
    32

    FW_RT-N53

    Новые тестовые бета-прошивки от Асус:

    Quote Originally Posted by Viktor_k, 09:20, 27-06-2012
    • add http://www.tunnelbroker.net ddns support
    • add Vitual Server and HW Accelerator coexistance
    • add Virtual Server raw protocol forward support
    • fix Multicast Forwarding as well as IPTV issues
    • fix WEB UI crash on client SSL close, add keealive client connections
    • fix WEB UI crash at IPv6 page
    • fix WEB UI crash on long tables (vserver, manual dhcp, etc)
    • fix WEB UI error at USB Modem page
    • fix WEB UI port ranges validation
    • fix WEB UI tables lost after row delete
    • fix WEB UI VPN Server page errors
    • fix VPN server to not accept IP addresses from VPN Client
    • fix crash in IPv6 firewall
    • improve L2TP driver
    • improve L2TP client, fixes compatibility issues with high-speed ISP Beeline tarifs
    • improve PPTP driver
    • improve WMF if EMF is enabled or Wireless Multicast rate is set
    • improve Virtual Server and UPNP forward speed
    http://forum.asus.ru/viewtopic.php?f=4&t=44107
    http://forum.asus.ru/viewtopic.php?p=361473#p361473
    Last edited by Omega; 24-07-2012 at 06:26. Reason: fixed - add RT-N53 HW Accelerator & AiCloud support ?

  3. #18
    Quote Originally Posted by Omega View Post
    Новая тестовая бета-прошивка 3.0.0.3.151 от Асус:
    прошился веб морда стала заметно быстрее откликаться. заработал Ipv6 тунель.

  4. #19
    Join Date
    Mar 2009
    Location
    Russia, Moscow
    Posts
    2,112
    Blog Entries
    32

    FW_RT-N53_3.0.0.4_188

    ASUS RT-N53 Beta Firmware Version 3.0.0.4.188 31.08.2012

    httр://www.asus.ru/ftp/NW_TO_TEST/RT-N53_3.0.0.4_188.trx

    • Wireless fixes
    • DHCP fixes
    • IPv6 fixes

    .
    http://forum.asus.ru/viewtopic.php?f=4&t=44107

  5. #20
    Join Date
    Mar 2009
    Location
    Russia, Moscow
    Posts
    2,112
    Blog Entries
    32
    Новая тестовая прошивка для Asus RT-N53: 26.10.2012

    httр://www.asus.ru/ftp/NW_TO_TEST/RT-N53_3.0.0.4_252.trx

    • Black UI
    • PPPOE + IPTV fix
    .
    http://forum.asus.ru/viewtopic.php?f=4&t=44107

  6. #21
    Join Date
    Mar 2009
    Location
    Russia, Moscow
    Posts
    2,112
    Blog Entries
    32

  7. #22
    Join Date
    Mar 2009
    Location
    Russia, Moscow
    Posts
    2,112
    Blog Entries
    32

    FW_RT-N53_3.0.0.4_264

    Asus RT-N53 Firmware Version 3.0.0.4.264 (File Size 7 MB 2012.12.10 update)

    httр://dlcdnet.asus.com/pub/ASUS/wireless/RT-N53/FW_RT_N53_VER3004264.zip

    After upgrading to 3.0.0.4.264 from 2.1.1.1.xx, please press the reset button for more
    than 5 seconds to reset the system to the default settings. If you encounter a firmware
    upgrade failure with RT-N53, please download the latest utility to recover the router.


    Fix bugs:

    • 1. UI related bugs.
    • 2. Network map cannot show device name.
    • 3. QoS control for wired connected devices.
    • 4. Special character name/password issue in VPN server.
    • 5. PPPoE compatibility issue.
    • 6. L2TP compatibility issue.
    • 7. IPv6 6in4 memory leak
    • 8. Comcast IPv6 related issues.

    Modified

    • 1. Enable cross night setting in wireless radio on/off setting page.
    • 2. Change default wireless security to WPA-AES in QIS.
    • 3. Show more information in Network map.
    • 4. QoS user interface, shows applied rule in first page.
    • 5. Allow Upnp port redirect external port: 1-65535 to internal port 1024-65535
    .
    httр://www.asus.com/Networks/Wireless_Routers/RTN53/#download

  8. #23
    Join Date
    Feb 2008
    Location
    Dniepropetrovsk, Ukraine
    Posts
    1,526

    Question ASUS RT-N53 - стоковая прошивка. как перегрузить wl-high (5g) драйвер в консоле?

    ASUS RT-N53
    стоковая прошивка 374.4561

    для запуска 5G на RT-N53 в init-broadcom.c есть код:
    Code:
    #ifdef RTCONFIG_BRCM_USBAP
    /* We have to load USB modules after loading PCI wl driver so
    * USB driver can decide its instance number based on PCI wl
    * instance numbers (in hotplug_usb())
    */
    modprobe("usbcore");
    #ifdef LINUX26
    mount("usbfs", "/proc/bus/usb", "usbfs", MS_MGC_VAL, NULL);
    #else
    mount("usbdevfs", "/proc/bus/usb", "usbdevfs", MS_MGC_VAL, NULL);
    #endif /* LINUX26 */
    {
    char insmod_arg[128];
    int i = 0, maxwl_eth = 0, maxunit = -1;
    char ifname[16] = {0};
    int unit = -1;
    char arg1[20] = {0};
    char arg2[20] = {0};
    char arg3[20] = {0};
    char arg4[20] = {0};
    char arg5[20] = {0};
    char arg6[20] = {0};
    char arg7[20] = {0};
    const int wl_wait = 3; /* max wait time for wl_high to up */
    /* Save QTD cache params in nvram */
    sprintf(arg1, "log2_irq_thresh=%d", nvram_get_int("ehciirqt"));
    sprintf(arg2, "qtdc_pid=%d", nvram_get_int("qtdc_pid"));
    sprintf(arg3, "qtdc_vid=%d", nvram_get_int("qtdc_vid"));
    sprintf(arg4, "qtdc0_ep=%d", nvram_get_int("qtdc0_ep"));
    sprintf(arg5, "qtdc0_sz=%d", nvram_get_int("qtdc0_sz"));
    sprintf(arg6, "qtdc1_ep=%d", nvram_get_int("qtdc1_ep"));
    sprintf(arg7, "qtdc1_sz=%d", nvram_get_int("qtdc1_sz"));
    modprobe("ehci-hcd", arg1, arg2, arg3, arg4, arg5, arg6, arg7);
    /* Search for existing PCI wl devices and the max unit number used.
    * Note that PCI driver has to be loaded before USB hotplug event.
    * This is enforced in rc.c
    */
    #define DEV_NUMIFS 8
    for (i = 1; i <= DEV_NUMIFS; i++) {
    sprintf(ifname, "eth%d", i);
    if (!wl_probe(ifname)) {
    if (!wl_ioctl(ifname, WLC_GET_INSTANCE, &unit,
    sizeof(unit))) {
    maxwl_eth = i;
    maxunit = (unit > maxunit) ? unit : maxunit;
    }
    }
    }
    /* Set instance base (starting unit number) for USB device */
    sprintf(insmod_arg, "instance_base=%d", maxunit + 1);
    modprobe("wl_high", insmod_arg);
    /* Hold until the USB/HSIC interface is up (up to wl_wait sec) */
    sprintf(ifname, "eth%d", maxwl_eth + 1);
    i = wl_wait;
    while (wl_probe(ifname) && i--) {
    sleep(1);
    }
    if (!wl_ioctl(ifname, WLC_GET_INSTANCE, &unit, sizeof(unit)))
    cprintf("wl%d is up in %d sec\n", unit, wl_wait - i);
    else
    cprintf("wl%d not up in %d sec\n", unit, wl_wait);
    }
    #endif /* __CONFIG_USBAP__ */
    в логе после старта wl_high(5G) пояляется следующее:
    Code:
    Jan  1 02:00:12 kernel: usbcore: registered new interface driver usbfs
    Jan  1 02:00:12 kernel: usbcore: registered new interface driver hub
    Jan  1 02:00:12 kernel: usbcore: registered new device driver usb
    Jan  1 02:00:13 kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    Jan  1 02:00:13 kernel: ehci_hcd 0000:00:04.1: EHCI Host Controller
    Jan  1 02:00:13 kernel: ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
    Jan  1 02:00:13 kernel: ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting
    Jan  1 02:00:13 kernel: ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
    Jan  1 02:00:13 kernel: ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
    Jan  1 02:00:13 kernel: usb usb1: configuration #1 chosen from 1 choice
    Jan  1 02:00:13 kernel: hub 1-0:1.0: USB hub found
    Jan  1 02:00:13 kernel: hub 1-0:1.0: 2 ports detected
    Jan  1 02:00:13 kernel: usb 1-2: new high speed USB device using ehci_hcd and address 2
    Jan  1 02:00:13 kernel: usb 1-2: configuration #1 chosen from 1 choice
    Jan  1 02:00:13 kernel: Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future
    Jan  1 02:00:13 kernel: Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
    Jan  1 02:00:13 kernel: bcm_rpc_up: waiting to be connected
    Jan  1 02:00:13 kernel: bcm_rpc_buf_recv_mgn_high: Reason: 0 Dongle Version: 0x5648a89
    Jan  1 02:00:13 kernel: bcm_rpc_buf_recv_mgn_high: Connected!
    Jan  1 02:00:13 kernel: eth2: Broadcom BCMa8e4 802.11 Wireless Controller 5.110.27.20012
    Jan  1 02:00:13 kernel: usbcore: registered new interface driver dbus_usbdev
    т.е.
    - грузится wl_high драйвер и регистрирует usb устройство Dongle Version: 0x5648a89
    - поднимается интерфейс eth2
    - eth2 добавляется в br0

    КАК с помощью команд в консоле повторить тоже самое??????


    после
    modprobe -r wl_high
    Code:
    Jan  1 02:31:09 kernel: bcm_rpc_down
    Jan  1 02:31:09 kernel: DONGLE rpc dump:
    Jan  1 02:31:09 kernel: Version: 0x5648a89 State: 4
    Jan  1 02:31:09 kernel: session 105 trans 0xda0 oe_trans 0x46dd rtn_trans 0x0
    Jan  1 02:31:09 kernel: xactionID out of order 0 reorder ovfl 0 dropped hole 0
    Jan  1 02:31:09 kernel: reorder queue depth 0 first ID 0x0 reorder_q_depth_max 0, tossthreshold 40
    Jan  1 02:31:09 kernel: rpc_dbus_state_change: DBUS is down
    Jan  1 02:31:10 kernel: br0: port 3(eth2) entering disabled state
    Jan  1 02:31:10 kernel: device eth2 left promiscuous mode
    Jan  1 02:31:10 kernel: br0: port 3(eth2) entering disabled state
    Jan  1 02:31:10 kernel: bcm_rpc_down
    Jan  1 02:31:10 kernel: usbcore: deregistering interface driver dbus_usbdev
    если попробовать:
    modprobe wl_high instance_base=2 (или любую другую цифру от 0 до 8) то получаем:
    Code:
    Jan  1 02:34:36 kernel: Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future
    Jan  1 02:34:36 kernel: Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
    Jan  1 02:34:36 kernel: rpc_dbus_state_change: DBUS is down
    Jan  1 02:34:36 kernel: bcm_rpc_tp_attach: dbus_attach failed
    Jan  1 02:34:36 kernel: usbcore: registered new interface driver dbus_usbdev
    драйвер wl_high грузится, но usb устройство не добавляется и не поднимается интерфейс eth2.

    как же это все сделать из консоли?

    --> http://www.linksysinfo.org/index.php...0/#post-234676
    Last edited by Omega; 19-12-2014 at 21:45. Reason: можно будет посмотреть, как это реализовано на томатах ;) а вообще-то вайфай через usb - это еще те костыли из блобов :)

  9. #24
    Join Date
    Feb 2008
    Location
    Dniepropetrovsk, Ukraine
    Posts
    1,526

    Exclamation

    есть отличные новости. после того как ASUS выпустил прошивки для закрытия
    дыры в безопасности 3.0.0.4.376.3754, то теперь на моем моде:

    1. работает 5G WiFi RT-N53
    2. будут версии прошивок для 4Mb роутеров RT-N10P_V2, RT-N12, RT-N10D1

    и так свершилось!!! pre-mod8 test build для роутеров c 4-х метровым флэшем

    - RT-N10P_V2
    - RT-N12
    - RT-N10D1
    - RT-N10+

    папка pre-mod8/4mb

    ну и RT-N53 с рaбочим 5G WiFi

    папка pre-mod8/N53
    Last edited by Omega; 17-01-2015 at 18:33.

  10. #25
    RT-N53 5G при подключении ошибка
    в Tools 5 GHz: disabled
    Name:  53.JPG
Views: 1122
Size:  55.9 KB

  11. #26
    Join Date
    Feb 2008
    Location
    Dniepropetrovsk, Ukraine
    Posts
    1,526
    Quote Originally Posted by vutick View Post
    RT-N53 5G при подключении ошибка
    в Tools 5 GHz: disabled
    Какая версия и какую ошибку выдает?

    А там где температура - так и должно быть! это датчик температуры не работает.
    Last edited by AndreyPopov; 24-01-2015 at 11:41.

  12. #27
    Quote Originally Posted by AndreyPopov View Post
    Какая версия и какую ошибку выдает?

    А там где температура - так и должно быть!
    Снес дрова к wi fi адаптеру все заработало 5G
    Спасибо за прошивку тестирую пока все отлично

Page 2 of 2 FirstFirst 12

Similar Threads

  1. IP-TV на ASUS WL-520GC
    By sony in forum Russian Discussion - РУССКИЙ (RU)
    Replies: 88
    Last Post: 24-02-2012, 10:24
  2. Настройка FTP сервера на Asus WL-500gP
    By RonS in forum Russian Discussion - РУССКИЙ (RU)
    Replies: 259
    Last Post: 27-11-2011, 16:57
  3. Asus WL-520gC - настройка роутера
    By 2vv in forum Russian Discussion - РУССКИЙ (RU)
    Replies: 391
    Last Post: 09-04-2010, 11:16

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •