Сделал кабель по схеме взятой из этой темы
http://wl500g.info/showthread.php?t=...max3232&page=3
Подключил его к роутеру как нарисовано в этой теме
http://www.blog.lausdahl.com/post/Li...erial-mod.aspx
Подключил к Com1, запустил Putty (115200), включил роутер.
Консоль запустилась.
Code:
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Fri Jun 15 11:29:14 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing Devices.
No DPN
This is a Parallel Flash
Boot partition size = 262144(0x40000)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 003F7FFF (3899364)
nvram #03 003F8000 -> 003FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 003F7FFF (3899392)
nvram #02 003F8000 -> 003FFFFF (32768)
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.5
CPU type 0x29006: 264MHz
Total memory: 16384 KBytes
Total memory used by CFE: 0x80700000 - 0x80796350 (615248)
Initialized Data: 0x8072D1A0 - 0x8072F900 (10080)
BSS Area: 0x8072F900 - 0x80730350 (2640)
Local Heap: 0x80730350 - 0x80794350 (409600)
Stack Area: 0x80794350 - 0x80796350 (8192)
Text (code) segment: 0x80700000 - 0x8072D1A0 (184736)
Boot area (physical): 0x00797000 - 0x007D7000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.5
The boot is CFE
mac_init(): Find mac [00:1d:7e:4c:dd:86] in location 1
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0: hwaddr 00-1D-7E-4C-DD-86, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x2AF000 (2813952) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x8A4 (2212) (0xBC0408A4)
Offset2: 0x82E14 (536084) (0xBC0C2E14)
Header CRC: 0xBFC4D931
Calculate CRC: 0x98E71446
Boot program checksum is invalid
CMD: [flash -ctheader : flash1.trx]
Reading :: _tftpd_open(): retries=0/3
_tftpd_open(): retries=1/3
_tftpd_open(): retries=2/3
--------------------------------------------------------------------
здесь (tftp -i 192.168.11 put firmware.bin) прошиваю оригинальную прошивку
--------------------------------------------------------------------
Code:
Stop to blink diag led ...Done. 2814976 bytes read
fname=flash1.trx
CODE Pattern is correct! (N150)
Programming...
ERROR. Flash device write error at address 1c067690
Failed.: I/O error
Start to blink diag led ...
Check CRC of image1
Len: 0x2AF000 (2813952) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x8A4 (2212) (0xBC0408A4)
Offset2: 0x82E14 (536084) (0xBC0C2E14)
Header CRC: 0xBFC4D931
Calculate CRC: 0x6025872A
Boot program checksum is invalid
CMD: [flash -ctheader : flash1.trx]
Reading :: _tftpd_open(): retries=0/3
Failed.: Network protocol error
Start to blink diag led ...
Check CRC of image1
Len: 0x2AF000 (2813952) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x8A4 (2212) (0xBC0408A4)
Offset2: 0x82E14 (536084) (0xBC0C2E14)
Header CRC: 0xBFC4D931
Calculate CRC: 0xC85A2F8F
Boot program checksum is invalid
CMD: [flash -ctheader : flash1.trx]
Reading :: _tftpd_open(): retries=0/3
_tftpd_open(): retries=1/3
_tftpd_open(): retries=2/3
Failed.: Timeout occured
CMD: [flash -ctheader : flash1.trx]
Reading :: _tftpd_open(): retries=0/3
_tftpd_open(): retries=1/3
_tftpd_open(): retries=2/3
Failed.: Timeout occured
CMD: [flash -ctheader : flash1.trx]
Reading :: _tftpd_open(): retries=0/3
---------------------------------------------------------
И так далее по кругу, идет предложение от tftpd
--------------------------------------------------------
Итог: ERROR. Flash device write error at address 1c067690
С этим можно что-то сделать??? - нужен совет!!!