I have copy all what i see on the terminal
echo.pdf - 43.8 Kb
thanks for help
What's the capacity of the USB storage that you use (I have the feeling that it's too small as already creating of partitions fail)? It should be bigger than 2GB as 256M is used for swap and 1GB for /opt and the rest for /mnt.
Btw I'll extend the tutorial to mention this.
jo thats the problem
thank you for you help
I've tried both SabNZB and HellaNZB, installed with this howto. Both have problems at my setup:
- SabNZB crashes when the webinterface is used. Downloading works, however without a webinterface it is inconvenient
- HellaNZB stalls after a while, mostly after working for some quarters of an hour. Only restarting helps. The log file doesn't offer useful info. On internet it shows that stalling of Hellanz happens more on different platforms (especially earlier versions).
Currently I am using this "work-around" (quite drastic, I must say). In cron.hourly I've put an executable script with this contents:
killall python2.5
sleep 10
/opt/bin/startHellaNZB
If others experience these problems too, a warning in the howto is advisable.
I am using:RT-N16-1.9.2.7-rtn-r1799.trx of the 15th of July by the way. I haven't tried newer versions of OLEG firmware
Most probably it has nothing to do with the firmware, but more with dependent libraries etc.
What you could do is upgrading packages with ipkg install <pkg name> (Don't forget to save /opt/etc before doing so!)
E.g. ipkg install python25 py25-hellanzb
You can check installed packages with ipkg list_installed
If you download the .ipkg file (e.g. with wget) from http://ipkg.nslu2-linux.org/feeds/op.../cross/stable/ you can look into it with mc (just enter when on the file) and check dependent packages in control file.
E.g.(set the version number at the end to the actual version)Code:cd /mnt && wget http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/py25-hellanzb_0.13-2_mipsel.ipk
If you figure out what has to be changed I'll fix it in the install script.
I will try that and report.
I found out that using an own username instead of admin (as prescribed in the tutorial) gives problems. For example cron doesn't work, as it is based on admin as username to work. My bad...
I hope this won't cause any more troubles. Can't be sure now that problems like I have with hellanzb and sabnzb are caused by that
I also had to tune mediatomb, in order to get it working. Also there a username is needed for good behaviour.....
@ecaddict
Instead of installing some current versions of libraries, I've done a full ipkg update and ipkg upgrade. I did answer all the questions about changing appr. 10 config files with No.
I like the result: midnight commander works now !
SABnzbd however stills quits with a segmentation fault directly after opening the web control page
For the rest I see no changes in behaviour. Like MC more programs might be affected with old libraries/packages. I would advise people to do ipkg upgrade in de howto, right after the ipkg update. If they answer all answers with no and change the conf-file for light-httpd, they have a better system!
Hi,
[not sure if this is the correct thread if not, admin, please move it.]
just bought RT-N16 router and flashed latest Oleg's fw on it so i'm pretty new to these things.
on the old router with fixed firmware i had "sent logs to email" option which sent logfile each hour to specified email address.
is it possible to have something similar on RT-N16 with Oleg's fw - i know that it probably needs some custom script - but hopefully somebody already created something similar
thank you in advance
krajicek
Last edited by krajicek; 29-08-2010 at 19:00.
I have RT-N16 with latest Oleg firmware (1.9.2.7-rtn-r2274).
I did configuration follow to ecaddict's manual.
But I have a problem with rtorrent: the error [File chunk write error: Cannot allocate memory.] after few minutes from start router.
I only have a few torrents (less than 10).
What is wrong and how do I fix it?
Thanks,
Slawek
Rather, it is not a problem with the disc capacity:
so I swap space:Code:[admin@Router ]$ df Filesystem 1K-blocks Used Available Use% Mounted on rootfs 5248 5248 0 100% / /dev/root 5248 5248 0 100% / devfs 63276 0 63276 0% /dev tmpfs 63276 200 63076 1% /tmp /dev/sda3 479478544 50636612 404485788 12% /mnt /dev/sda2 988244 279236 658808 30% /opt
Code:[admin@Router /]$ free total used free shared buffers cached Mem: 126552 124564 1988 0 540 96956 -/+ buffers/cache: 27068 99484 Swap: 257000 188 256812
The router has a standard clock.
Thanks
Last edited by SlawekW; 20-11-2010 at 12:09.