New Asus RT-N16 Router

[wpte]

hello pedro, sorry to respond so late, I've been away on holday and unable to test this myself

Now I followed the same guide you followed and also I have been unable to connect to the server. After windows tried to verify the username and password it wouldn't pass the connecting part...

It simply shows an 800 error.
Also, doesn't L2TP use port 1723?

things you could try are to place all the configuration scripts on the flasfs instead of harddrive, just in case.
Also you can just entire folders to the .files like:

/etc/l2tp

it will save that folder including every sub file/folder

[oldgringo]

Hi guys, I've got one problem which can't solve for weeks. My rt-n16 automaticaly disconnects and then reconnects every 24 hours. It's not a matter of line provider, with another device I can get stable connection for weeks without interrupts. I set Idle Disconnect Time in seconds(option) to zero, but still problem occurs. Is there any other setting which I had to check?
Thanks.

[hggomes]

Hi guys, I've got one problem which can't solve for weeks. My rt-n16 automaticaly disconnects and then reconnects every 24 hours. It's not a matter of line provider, with another device I can get stable connection for weeks without interrupts. I set Idle Disconnect Time in seconds(option) to zero, but still problem occurs. Is there any other setting which I had to check?
Thanks.

What FW are you using? Original or Oleg?

Make sure you clean nvram via telnet/ssh and load defaults settings in GUI and try again.

You can also reset via hw botton on the back of the unit.

Good luck

[oldgringo]

I use Oleg's recent firmware version here. This problem persists since I moved from direct network vlan2 connection to pppoe through dsl modem, I've tried tens of fw versions from 2408 until now, everytime factory default but not work, there is pppoe reconnect every 24 hour. In my syslog I can see this:

May 7 17:57:49 PPPoE: Disconnected
May 7 17:57:52 pppd[1354]: Connection terminated.
May 7 17:57:52 pppd[1354]: Modem hangup
May 7 17:58:22 pppd[1354]: Connected to xx:xx:xx:xx:xx:xx via interface vlan2
May 7 17:58:22 pppd[1354]: Connect: ppp0 <--> vlan2
May 7 17:58:23 pppd[1354]: PAP authentication succeeded
May 7 17:58:23 pppd[1354]: peer from calling number xx:xx:xx:xx:xx:xx authorized
May 7 17:58:23 pppd[1354]: local IP address yyy.yyy.yyy.yyy
May 7 17:58:23 pppd[1354]: remote IP address zzz.zzz.zzz.zzz
May 7 17:58:25 PPPoE: connected to ISP

[hggomes]

You are making a bridge with a dial up device, what modem model is?

[oldgringo]

Zyxel Prestige 660HN-T3A in bridge mode

[hggomes]

I never try with that specific model but i've never had any problem with PPPoE Bridges at all with RT-N16, not sure what is happening... Have you cleaned nvram (not defaults) sucessfuly after update the fw?

[oldgringo]

I started everything from the scratch, clear everything, loaded latest firmware, factory defaults and only basic settings (pppoe and dhcp) but after 24 hours again reconnect. I have to check another dsl modem, it's probably my last hope.

[hggomes]

Yeah thats the way to go, good luck

[QMax]

Due to an hardware fault of my WL-500W, in the next days I'll replace it with a new RT-N16.
I was running WL500W-1.9.2.7-rtn-r4051.trx, and I'll flash RT-N16-1.9.2.7-rtn-r4051.trx.

Is it possible to save settings.cfg and flashfs from my old router and upload it on the RT-N16 (I know of different flash size) ?

Thanks

Max

[yoni]

Hey,

How can I revert back to Asus original firmware on RT-N16?

I tried to "upgrade" using the web interface and it didn't work, I tried Asus restoration utility and it was unable to connect and last I tried tftp and got "Error on server : transfer cancelled" (I also tried several different tftp programs and o of course I put the router in recovery mode)

It there an "official way" of doing it?


Thanks,
Yoni

[hggomes]

Press RESET botton and power it on (power light will blink), it will be in recover mode. Now use ASUS Firmware Restoration tool and upload the firmware.

[hggomes]

There are problems with last builds of Oleg Firmware (at least R4517, R4519 and R4520), after upgrade change for example SSID and save & reboot, will not save configuration...

R4502 is OK!

[lly]

There are problems with last builds of Oleg Firmware (at least R4517, R4519 and R4520), after upgrade change for example SSID and save & reboot, will not save configuration...

R4502 is OK!

Confirmed, bug introduced in r4516. Fixed in r4522.

[hggomes]

Great, tks ;-)