I got the message: "could'nt connect to server".
Never happends with previous fw versions up to 1.9.3.5!
Grrrr... I know this is beta one but seems that new versions always lost things that worked well before
WARNING: BETA VERSION
TRY AT YOUR OWN RISK!
DO NOT UPGRADE UNLESS YOU KNOW WHAT YOU ARE DOING
DOWNGRADE IS NOT EASILY POSSIBLE!!
Changelog:
important!!1. Fix: reset to default problem
2. Fix: wireless range problem
3. Chg: pppoe package for idle disconnect timeout
4. Add: support connection of NAT track to 4096
find files here:When upgrading from 1.7.x.x based firmware: you MUST Reset your WL500g to defaults via the restore button at the back after upgrading to this firmware!
you do not have to do this when you upgrade from 1.8.x.x based firmware!
but we RECOMMEND you to do a restore to defaults.
Do not import saved settings from older/other firmwares! this can cause unstability to your device
Mirror @ Chupa.nl
http://files.wl500g.info/asus/wl500g...0g_1936_EN.zip
cK LEe notified me by mail of the existence.
Last edited by Antiloop; 20-03-2005 at 02:36.
My little Asus Collection: Too much to fit inhere, my 2 babies:WL500w 1.9.2.7-10(OLEG) VX2SE Yellow Lamborghini notebook
WL500g Forum Asus Files OpenDir
Asusforum.NL -- Asusforum.DE -- Asusforum.RU -- Asusforum.PL -- Asusforum.NET -- Asusforum.EU -- Asusforum.BE -- Asusforum.ES -- Asusforum.INFO
I got the message: "could'nt connect to server".
Never happends with previous fw versions up to 1.9.3.5!
Grrrr... I know this is beta one but seems that new versions always lost things that worked well before
The connection speed is really low using 1.9.3.X version firmware.
I am using VDSL 10Mbps with PPPOE
(It changed from 1.2MB/s [in 1.9.2.x ] to 400KB/s, however, 1.9.3.X is more stable. The connection seldom disconnects.)
doesn't seem to be telnet or dropbear running with this release...hmm..
ASUS releases never have such things. This is not custom firmware.Originally Posted by jago25_98
After applying Firmware upgrade the reset function is not working anymore.
Tried different things -> power off for an hour, pressing reset button 5 seconds and keeping pressed during power on, pressing button for about 1 minute etc. but nothing is succesfull. Power led will not burn anymore while LAN led is flashing. No connection is possible at the moment.
Anyone an idea how to get the router in control again?
Last edited by newbie; 22-03-2005 at 08:47.
you can try to connect pin10 from the flash (AMD) chip to ground while powering on, this should force the unit to go into firmware recovery mode so you can reflash firmware and start overOriginally Posted by newbie
My little Asus Collection: Too much to fit inhere, my 2 babies:WL500w 1.9.2.7-10(OLEG) VX2SE Yellow Lamborghini notebook
WL500g Forum Asus Files OpenDir
Asusforum.NL -- Asusforum.DE -- Asusforum.RU -- Asusforum.PL -- Asusforum.NET -- Asusforum.EU -- Asusforum.BE -- Asusforum.ES -- Asusforum.INFO
I'll try this but as a newbie I've never done so before. Can you explain me where I can find the (flash) chip on the print after opening the device? and which pin is pin10?Originally Posted by Antiloop
which ground can I use?-> outside surface of power connector?
Last edited by newbie; 22-03-2005 at 12:38.
reboot issue. (fw 1.9.3.6)
Last edited by int; 24-03-2005 at 06:57.
Home Page
Marco Sousa from PORTUGAL
[ WL-500g - fw: 1.9.2.7-7e [Oleg] | WL-500gP - fw: 1.9.2.7-7f-USB-1.63 [Oleg&koppel.cz] ]
What happens if you, regardless of what the LEDs do, try to do the firmware restoration trick?Originally Posted by newbie
What I mean is:
- Bring the unit in restoration modem (power off, reset, power on while reset, hold reset for another 10 seconds, then release reset button).
- Prepare pc for restoration (single ethernet interface enabled, fixed ip address).
- Run restoration tool.
More info here: http://wl500g.info/showthread.php?p=8236
Report results here please.
At 1.9.3.5 and later it normally worked....
You mean and prior/earlier ...Originally Posted by Viper_Rus
Yes, 1.9.3.5 and earlierOriginally Posted by tomilius
USB printer does not work here either (HP DeskJet 940C). The USB port works for pen drives, though.Originally Posted by Viper_Rus
Let's first say that I'm a newby, but I have read a lot of postings on the forum. Now my problem:
I recently purchased the WL-500g with firmware version 1.8.1.9. I'm trying to connect my Canon ip3000 printer to the wl500, but without success. I know there are some posting regarding this item but they did not help. The printer wizard doesn't indicate any problem and the port automatically switches to a 'standard tcp/ip port', but when I want to print something, nothing happens. The protocol is RAW and the port number is 9100. Bidirectional communication on or off does not make any difference.
The next step I want to do now is to upgrade the wl500g firmware. On the site of Asus a 1.9.3.6 beta version is available, with among others 'a range problem' solved. On this forum the latest version seems to be 1.9.2.7 CR4.
Can I use this version or does it still have this range problem? Or do I have to wait for a final 1.9.3.6 version from Asus?
(My Asus is installed on the second floor and the laptop is mostly used at the ground floor (couch!). The receiver quality now is 3 out of 5 on average, so I'm a little bit worried about this range problem.)
System info:
FW version: 1.8.1.9
mode: access point
security: WPA-PSK
PC: Windows XP SP2
printer: Canon PIXMA ip3000, with latest drivers
Any help appreciated!
Theo.