Results 1 to 8 of 8

Thread: Kingston 16Gb DT 100 = I/O error: dev 08:00, sector 0

  1. #1

    Kingston 16Gb DT 100 = I/O error: dev 08:00, sector 0

    Hi !

    I have bought Kingston DataTraveler 100 16Gb pen, but I can't use it.
    I have " I/O error: dev 08:00 sector 0 " in dmesg ,and sometimes random "permission denied" messages, when I want use program on it .
    Code:
    Jan  1 01:00:03 kernel: usb.c: registered new driver usbdevfs
    Jan  1 01:00:03 kernel: usb.c: registered new driver hub
    Jan  1 01:00:03 kernel: usb-uhci.c: $Revision: 1.275 $ time 20:50:46 Mar 17 2008
    Jan  1 01:00:03 kernel: usb-uhci.c: High bandwidth mode enabled
    Jan  1 01:00:03 kernel: PCI: Enabling device 01:03.0 (0000 -> 0001)
    Jan  1 01:00:03 kernel: ECHI PCI device 30381106 found.
    Jan  1 01:00:03 kernel: UCHI reg 0x41 = 10
    Jan  1 01:00:03 kernel: UCHI reg 0x41 changed to = 0
    Jan  1 01:00:03 kernel: usb-uhci.c: USB UHCI at I/O 0x100, IRQ 12
    Jan  1 01:00:03 kernel: usb-uhci.c: Detected 2 ports
    Jan  1 01:00:03 kernel: usb.c: new USB bus registered, assigned bus number 1
    Jan  1 01:00:03 kernel: hub.c: USB hub found
    Jan  1 01:00:03 kernel: hub.c: 2 ports detected
    Jan  1 01:00:03 kernel: PCI: Enabling device 01:03.1 (0000 -> 0001)
    Jan  1 01:00:03 kernel: ECHI PCI device 30381106 found.
    Jan  1 01:00:03 kernel: UCHI reg 0x41 = 10
    Jan  1 01:00:03 kernel: UCHI reg 0x41 changed to = 0
    Jan  1 01:00:03 kernel: usb-uhci.c: USB UHCI at I/O 0x120, IRQ 12
    Jan  1 01:00:03 kernel: usb-uhci.c: Detected 2 ports
    Jan  1 01:00:03 kernel: usb.c: new USB bus registered, assigned bus number 2
    Jan  1 01:00:03 kernel: hub.c: USB hub found
    Jan  1 01:00:03 kernel: hub.c: 2 ports detected
    Jan  1 01:00:03 kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
    Jan  1 01:00:03 kernel: PCI: Enabling device 01:03.2 (0000 -> 0002)
    Jan  1 01:00:03 kernel: ehci_hcd 01:03.2: PCI device 1106:3104
    Jan  1 01:00:03 kernel: ehci_hcd 01:03.2: irq 12, pci mem c011c000
    Jan  1 01:00:03 kernel: usb.c: new USB bus registered, assigned bus number 3
    Jan  1 01:00:03 kernel: ECHI PCI device 31041106 found.
    Jan  1 01:00:03 kernel: ECHI reg 0x49 = 80010f20
    Jan  1 01:00:03 kernel: ECHI reg 0x49 changed to = 80010f00
    Jan  1 01:00:03 kernel: ECHI reg 0x4b = 80010f09
    Jan  1 01:00:03 kernel: ECHI reg 0x4b changed to = 80010f29
    Jan  1 01:00:03 kernel: PCI: 01:03.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32
    Jan  1 01:00:03 kernel: ehci_hcd 01:03.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
    Jan  1 01:00:03 kernel: hub.c: USB hub found
    Jan  1 01:00:03 kernel: hub.c: 4 ports detected
    Jan  1 01:00:03 kernel: usb.c: registered new driver usblp
    Jan  1 01:00:03 kernel: printer.c: v0.13: USB Printer Device Class driver
    Jan  1 01:00:04 kernel: hub.c: connect-debounce failed, port 1 disabled
    Jan  1 01:00:04 kernel: hub.c: new USB device 01:03.2-1, assigned address 2
    Jan  1 01:00:04 kernel: usb.c: USB device 2 (vend/prod 0x951/0x1607) is not claimed by any active driver.
    Jan  1 01:00:05 kernel: usb.c: registered new driver audio
    Jan  1 01:00:05 kernel: audio.c: v1.0.0:USB Audio Class driver
    Jan  1 01:00:05 kernel: Linux video capture interface: v1.00
    Jan  1 01:00:05 kernel: SCSI subsystem driver Revision: 1.00
    Jan  1 01:00:05 kernel: Initializing USB Mass Storage driver...
    Jan  1 01:00:05 kernel: usb.c: registered new driver usb-storage
    Jan  1 01:00:05 kernel: scsi0 : SCSI emulation for USB Mass Storage devices
    Jan  1 01:00:05 kernel:   Vendor: Kingston  Model: DataTraveler 2.0  Rev: 1.00
    Jan  1 01:00:05 kernel:   Type:   Direct-Access                      ANSI SCSI revision: 02
    Jan  1 01:00:05 kernel: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
    Jan  1 01:00:05 kernel: SCSI device sda: 31506432 512-byte hdwr sectors (16131 MB)
    Jan  1 01:00:05 kernel: sda: Write Protect is off
    Jan  1 01:00:05 kernel: Partition check:
    Jan  1 01:00:06 kernel:  p1
    Jan  1 01:00:06 kernel: USB Mass Storage support registered.
    Jan  1 01:00:32 kernel:  I/O error: dev 08:00, sector 0
    Jan  1 01:00:32 kernel: SCSI device sda: 31506432 512-byte hdwr sectors (16131 MB)
    Jan  1 01:00:32 kernel: sda: Write Protect is off
    Jan  1 01:00:32 kernel:  p1
    Jan  1 01:00:32 kernel: MSDOS FS: IO charset utf8
    Jan  1 01:00:32 kernel: MSDOS FS: Using codepage 866
    Jan  1 01:00:32 USB storage: vfat fs at /dev/discs/disc0/part1 mounted to /tmp/mnt/disc0_1
    same with ext3 filesystem
    Fdisk say:
    Code:
    $ fdisk /dev/discs/disc0/disc 
    
    The number of cylinders for this disk is set to 1961.
    There is nothing wrong with that, but this is larger than 1024,
    and could in certain setups cause problems with:
    1) software that runs at boot time (e.g., old versions of LILO)
    2) booting and partitioning software from other OSs
       (e.g., DOS FDISK, OS/2 FDISK)
    
    Command (m for help):
    Another 1Gb (A-Data) pen works right with it.
    I can use the Kingston on my laptop without error and error messages (2.6.27 kernel)

    My firmware is:
    1.9.2.7-10

    After unload and load back the usb modules nothing happend.

    Thx

  2. #2
    The same problem with my Kingston 16Gb DT

  3. #3
    The same problem with Goodram Gooddrive Twister 2 Gb. =(
    Any issues / ideas?

  4. #4

    16 GB USB flash kingston can't be mounted on wl-500gp

    Hello,
    i have an issue with my wl500gp and kingston flashdisk 16GB. I'm using Oleg firmware version 1.9.2.7-9. I tried to attach my flashdisk to router, but it does'nt appear. I already tried to format it to NTFS, FAT32, EXT3, EXT2 but no changes. Here's the result of df and dmesg commands:

    PHP Code:
    [admin@WL-00221516E22B root]$ df -h
    Filesystem                Size      Used Available 
    Use% Mounted on
    /dev/root                 2.9M      2.9M         0 100% /
    [
    admin@WL-00221516E22B root]$

    [
    admin@WL-00221516E22B root]$ dmesg
    target0
    /lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
    VFS
    Disk change detected on device 08:10
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
    usb
    .cUSB disconnect on device 01:03.2-2 address 5
    Device not ready
    .  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:10
    sdb 
    READ CAPACITY failed.
    sdb status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sdb 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
    Device not ready
    .  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:20
    sdc 
    READ CAPACITY failed.
    sdc status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sdc 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host2/bus0/target0/lun0I/O errordev 08:20sector 0
     I
    /O errordev 08:20sector 0
    Device not ready
    .  Make sure there is a disc in the drive.
    sdc READ CAPACITY failed.
    sdc status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sdc 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host2/bus0/target0/lun0I/O errordev 08:20sector 0
     I
    /O errordev 08:20sector 0
     unable to read partition table
    hub
    .c: new USB device 01:03.2-1assigned address 6
    WARNING
    USB Mass Storage data integrity not assured
    USB Mass Storage device found at 6
    Device not ready
    .  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:00
    Device busy 
    for revalidation (usage=1)
    Device not ready.  Make sure there is a disc in the drive.
    sda READ CAPACITY failed.
    sda status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sda 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host0/bus0/target0/lun0I/O errordev 08:00sector 0
     I
    /O errordev 08:00sector 0
     unable to read partition table
    VFS
    Disk change detected on device 08:10
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0p1 p2
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
     unable to read partition table
     I
    /O errordev 08:10sector 0
    VFS
    Disk change detected on device 08:10
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
    VFS
    Disk change detected on device 08:10
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
    VFS
    Disk change detected on device 08:10
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
    VFS
    Disk change detected on device 08:10
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
    Device not ready
    .  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:20
    sdc 
    READ CAPACITY failed.
    sdc status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sdc 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host2/bus0/target0/lun0I/O errordev 08:20sector 0
     I
    /O errordev 08:20sector 0
    Device not ready
    .  Make sure there is a disc in the drive.
    sdc READ CAPACITY failed.
    sdc status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sdc 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host2/bus0/target0/lun0I/O errordev 08:20sector 0
     I
    /O errordev 08:20sector 0
     unable to read partition table
    Device not ready
    .  Make sure there is a disc in the drive.
    sda READ CAPACITY failed.
    sda status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sda 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host0/bus0/target0/lun0I/O errordev 08:00sector 0
     I
    /O errordev 08:00sector 0
     unable to read partition table
    Device not ready
    .  Make sure there is a disc in the drive.
    sda READ CAPACITY failed.
    sda status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sda 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host0/bus0/target0/lun0I/O errordev 08:00sector 0
     I
    /O errordev 08:00sector 0
     unable to read partition table
    Device not ready
    .  Make sure there is a disc in the drive.
    sda READ CAPACITY failed.
    sda status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sda 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host0/bus0/target0/lun0I/O errordev 08:00sector 0
     I
    /O errordev 08:00sector 0
     unable to read partition table
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
     unable to read partition table
    SCSI device sdb
    31309760 512-byte hdwr sectors (16031 MB)
    sdbWrite Protect is off
     
    /dev/scsi/host1/bus0/target0/lun0I/O errordev 08:10sector 0
     I
    /O errordev 08:10sector 0
     unable to read partition table
     I
    /O errordev 08:10sector 0
    Device not ready
    .  Make sure there is a disc in the drive.
    sdc READ CAPACITY failed.
    sdc status 1message 00host 0driver = 08
    Info fld=0xa00 (nonstd), Current sd00:00sns 70  2
    Raw sense data
    :0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00
    sdc 
    block size assumed to be 512 bytesdisk size 1GB.
     /
    dev/scsi/host2/bus0/target0/lun0I/O errordev 08:20sector 0
     I
    /O errordev 08:20sector 0
     unable to read partition table
    Device not ready
    .  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:00
    Device busy 
    for revalidation (usage=1)
    Device not ready.  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:00
    Device busy 
    for revalidation (usage=1)
    Device not ready.  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:00
    Device busy 
    for revalidation (usage=1)
    Device not ready.  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:00
    Device busy 
    for revalidation (usage=1)
    Device not ready.  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:00
    Device busy 
    for revalidation (usage=1)
    Device not ready.  Make sure there is a disc in the drive.
    VFSDisk change detected on device 08:00
    Device busy 
    for revalidation (usage=1)
    [
    admin@WL-00221516E22B root]$ 
    Also i tried with my other flashdisks (1GB and 4GB) it works properly.

    Any ideas?

    Thanks
    Last edited by Wustas; 06-09-2009 at 14:43.

  5. #5
    Join Date
    Jun 2006
    Location
    Romania
    Posts
    19

    Lightbulb Try this

    Try updating your firmware to WL-500gP 1.9.2.7-d-r473 from this link http://code.google.com/p/wl500g/downloads/list , also try to unmount your flash stik and mount it again.

    Good luck!

    Best regards,

    Renegate
    Last edited by Renegate; 06-09-2009 at 17:49.

  6. #6

    Thanks

    after the upgrade everything works fine.

  7. #7
    Updating to the latest firmware from http://code.google.com/p/wl500g/downloads/list may solve the problem. See http://wl500g.info/showthread.php?t=21032

  8. #8

    Smile

    Thanks Renegate! I just got a 16GB Kingston Data Traveler 102 (DT102/16GB) and I had a similar problem in WL500W-1.9.2.7-10. Upgrading to WL500W-1.9.2.7-d-r1222 fixed the problem. I'm attaching a text file containing dmesg output.
    Attached Files Attached Files

Similar Threads

  1. Проблема с подключением Flash к роутеру
    By unnamed777 in forum Russian Discussion - РУССКИЙ (RU)
    Replies: 61
    Last Post: 28-01-2010, 21:00
  2. WL-500gP with a WD my book pro II 1TB I/O errors
    By golem in forum WL-500gP Q&A
    Replies: 1
    Last Post: 14-06-2007, 22:14
  3. USB Stick problem - Pretec iTiny 128 MB
    By S474N in forum WL-500gP Q&A
    Replies: 0
    Last Post: 06-03-2007, 13:56

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •