Code:
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:03.0 to 64
usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
usb-ohci.c: usb-00:03.0, PCI device 14e4:471a
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF 81fdcf20, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB OHCI Root Hub
SerialNumber: b8003000
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: no over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 4ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface 81fdcf20
usb.c: kusbd: /sbin/hotplug add 1
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
PCI: Setting latency timer of device 00:03.1 to 64
ehci_hcd 00:03.1: PCI device 14e4:471a
ehci_hcd 00:03.1: irq 6, pci mem b8003800
usb.c: new USB bus registered, assigned bus number 2
ehci_hcd 00:03.1: ehci_start hcs_params 0x1212 dbg=0 cc=1 pcc=2 ordered ports=2
ehci_hcd 00:03.1: ehci_start hcc_params a010 thresh 1 uframes 1024
ehci_hcd 00:03.1: capability 0000 at a0
ehci_hcd 00:03.1: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 00:03.1: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 00:03.1: USB 0.0 enabled, EHCI 1.00, driver 10 Dec 2004/2.4
hcd.c: 00:03.1 root hub device address 1
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
usb.c: kmalloc IF 8198e2a0, numif 1
usb.c: new device strings: Mfr=3, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Manufacturer: Linux 2.4.37.6 ehci_hcd
Product: PCI device 14e4:471a
SerialNumber: 00:03.1
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: individual port power switching
hub.c: individual port over-current protection
hub.c: Single TT
hub.c: TT requires at most 8 FS bit times (666 ns)
hub.c: Port indicators are not supported
hub.c: power on to power good time: 20ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
usb.c: hub driver claimed interface 8198e2a0
usb.c: kusbd: /sbin/hotplug add 1
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
ehci_hcd 00:03.1: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
SCSI subsystem driver Revision: 1.00
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
vlan2: Setting MAC address to 00 1b 11 33 f6 9d.
vlan2: add 01:00:5e:00:00:01 mcast address to master interface
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
ehci_hcd 00:03.1: port 1 high speed
ehci_hcd 00:03.1: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
hub.c: port 1, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:03.1-1, assigned address 2
usb.c: kmalloc IF 8198e600, numif 1
usb.c: new device strings: Mfr=0, Product=1, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Product: USB2.0 Hub
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Single TT
hub.c: TT requires at most 32 FS bit times (2664 ns)
hub.c: Port indicators are supported
hub.c: power on to power good time: 100ms
hub.c: hub controller current requirement: 100mA
hub.c: port removable status: RRRR
hub.c: local power source is good
hub.c: no over-current condition exists
ehci_hcd 00:03.1: link qh 256-0001/a1900100 start 255 [1/0 us]
ehci-sched.c: scheduled qh a1900100 usecs 1/0 period 256.0 starting 255.0 (gap 0)
hub.c: enabling power on all ports
usb.c: hub driver claimed interface 8198e600
usb.c: kusbd: /sbin/hotplug add 2
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 101, change 1, 12 Mb/s
hub.c: port 3 connection change
hub.c: port 3, portstatus 101, change 1, 12 Mb/s
hub.c: port 3, portstatus 101, change 0, 12 Mb/s
hub.c: port 3, portstatus 101, change 0, 12 Mb/s
hub.c: port 3, portstatus 101, change 0, 12 Mb/s
hub.c: port 3, portstatus 101, change 0, 12 Mb/s
hub.c: port 3, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:03.1-1.3, assigned address 3
usb.c: kmalloc IF 8198e720, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 3 default language ID 0x409
Manufacturer: USBest Technology
Product: USB Mass Storage Device
SerialNumber: 08041800057110
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Ut165 Model: USB2FlashStorage Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 7897088 512-byte hdwr sectors (4043 MB)
sda: Write Protect is off
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
usb.c: usb-storage driver claimed interface 8198e720
usb.c: kusbd: /sbin/hotplug add 3
hub.c: port 4, portstatus 101, change 1, 12 Mb/s
hub.c: port 4 connection change
hub.c: port 4, portstatus 101, change 1, 12 Mb/s
hub.c: port 4, portstatus 101, change 0, 12 Mb/s
hub.c: port 4, portstatus 101, change 0, 12 Mb/s
hub.c: port 4, portstatus 101, change 0, 12 Mb/s
hub.c: port 4, portstatus 101, change 0, 12 Mb/s
hub.c: port 4, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:03.1-1.4, assigned address 4
usb.c: kmalloc IF 8198e9e0, numif 1
usb.c: new device strings: Mfr=1, Product=3, SerialNumber=2
usb.c: USB device number 4 default language ID 0x409
Manufacturer: Super Top
Product: USB 2.0 IDE DEVICE
SerialNumber: ??????????
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usb.c: registered new driver hci_usb