Page 1 of 4 123 ... LastLast
Results 1 to 15 of 54

Thread: Firmware v1.9.2.7 CR1 [Oleg]

  1. #1
    Join Date
    Dec 2003
    Location
    Russian Federation
    Posts
    8,353

    Firmware v1.9.2.7 CR1 [Oleg]

    New firmware, as well as sources are available for download. Please visit this page if you need further information.

    Changes are:
    • Used GPL 1.9.2.7 sources, WPA2 & WME disabled for now
    • WL-500gx support
    • Hopefully, dnsmasq-"starcraft" issue fixed (in fact it looks like race condition)
    • Syslog is now also running in AP mode
    • Fixed 1.8.1.7-3 samba problems
    • Added new busybox applet: crond
    • Web interface shows decoded uptime now
    • Changed PPPoE behaviour to be compatible with stock firmware, added 2 new nvram variables:
      * wan0_pppoe_maxfail - terminate after wan0_pppoe_maxfail consecutive failed connection attempts. A value of 0 means no limit. The default value is 10.
      * wan0_pppoe_holdoff - specifies how many seconds to wait before re-initiating the link after it terminates.
    • Removed PPPoE mru/mtu 1500 warnings
    • Several new USB HP OfficeJet printers are supported now

  2. #2
    Join Date
    Aug 2004
    Location
    Germany
    Posts
    377
    Hi

    Again, nice Firmware. Crond is cool .
    All working fine here.

    What can this "ating" come from ?
    Code:
    Jan  1 01:00:01 kernel: br0: port 2(eth2) entering forwarding state
    Jan  1 01:00:01 kernel: ating
    Jan  1 01:00:01 kernel: br0: port 1(eth0) entering forwarding state
    Greets
    My Stuff: WL-500g, Mapower H31x 10GB HD, Philips Webcam Vesta PRO, TerraTec Webcam PRO, USB Hub

  3. #3
    Join Date
    Dec 2003
    Location
    Russian Federation
    Posts
    8,353
    I've no idea. Please post complete log.
    Last edited by Oleg; 19-12-2004 at 13:31.

  4. #4
    Join Date
    Aug 2004
    Location
    Germany
    Posts
    377
    Quote Originally Posted by Oleg
    I've no idea. Please post complete log.
    OK, here is syslog. The interresing part is around the bridge setup.
    Code:
    Jan  1 01:00:01 syslogd started: BusyBox v1.00 (2004.12.15-20:26+0000)
    Jan  1 01:00:01 kernel: klogd started: BusyBox v1.00 (2004.12.15-20:26+0000)
    Jan  1 01:00:01 kernel: cpu probe
    Jan  1 01:00:01 dnsmasq[51]: started, version 2.17 cachesize 150
    Jan  1 01:00:01 dnsmasq[51]: DHCP, IP range 192.168.1.200 -- 192.168.1.254, lease time 24h
    Jan  1 01:00:01 dnsmasq[51]: DHCP, /tmp/dnsmasq.log will be written every 28800s
    Jan  1 01:00:01 dnsmasq[51]: read /etc/hosts - 5 addresses
    Jan  1 01:00:01 dnsmasq[51]: reading /tmp/resolv.conf
    Jan  1 01:00:01 kernel: prom init
    Jan  1 01:00:01 kernel: cpu report
    Jan  1 01:00:01 kernel: CPU revision is: 00024000
    Jan  1 01:00:01 kernel: Loading BCM4710 MMU routines.
    Jan  1 01:00:01 kernel: Primary instruction cache 8kb, linesize 16 bytes (2 ways)
    Jan  1 01:00:01 kernel: Primary data cache 4kb, linesize 16 bytes (2 ways)
    Jan  1 01:00:01 kernel: Linux version 2.4.20 (root@omnibook) (gcc version 3.2.3 with Broadcom modifications) #4 Thu Dec 16 23:32:43 MSK 20
    [...]
    Jan  1 01:00:01 kernel: Checking for 'wait' instruction...  unavailable.
    Jan  1 01:00:01 kernel: POSIX conformance testing by UNIFIX
    Jan  1 01:00:01 kernel: PCI: Fixing up bus 0
    Jan  1 01:00:01 kernel: PCI: Fixing up bridge
    Jan  1 01:00:01 kernel: PCI: Fixing up bus 1
    Jan  1 01:00:01 kernel: Linux NET4.0 for Linux 2.4
    Jan  1 01:00:01 kernel: Based upon Swansea University Computer Society NET3.039
    Jan  1 01:00:01 kernel: Initializing RT netlink socket
    Jan  1 01:00:01 kernel: Starting kswapd
    Jan  1 01:00:01 kernel: Journalled Block Device driver loaded
    Jan  1 01:00:01 kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
    Jan  1 01:00:01 kernel: devfs: boot_options: 0x1
    Jan  1 01:00:01 kernel: NTFS driver v1.1.22 [Flags: R/O]
    Jan  1 01:00:01 kernel: pty: 256 Unix98 ptys configured
    Jan  1 01:00:01 kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
    Jan  1 01:00:01 kernel: PPP generic driver version 2.4.2
    Jan  1 01:00:01 kernel: PPP Deflate Compression module registered
    Jan  1 01:00:01 kernel: PPP BSD Compression module registered
    Jan  1 01:00:01 kernel:  Amd/Fujitsu Extended Query Table v1.0 at 0x0040
    Jan  1 01:00:01 kernel: Physically mapped flash: JEDEC Device ID is 0xCA. Assuming broken CFI table.
    Jan  1 01:00:01 kernel: Physically mapped flash: Swapping erase regions for broken CFI table.
    Jan  1 01:00:01 kernel: number of CFI chips: 1
    Jan  1 01:00:01 kernel: Flash device: 0x400000 at 0x1fc00000
    Jan  1 01:00:01 kernel: Physically mapped flash: squashfs filesystem found at block 1087
    Jan  1 01:00:01 kernel: Creating 5 MTD partitions on "Physically mapped flash":
    Jan  1 01:00:01 kernel: 0x00000000-0x00040000 : "pmon"
    Jan  1 01:00:01 kernel: 0x00040000-0x003e0000 : "linux"
    Jan  1 01:00:01 kernel: 0x0010fd24-0x003e0000 : "rootfs"
    Jan  1 01:00:01 kernel: 0x003f0000-0x00400000 : "nvram"
    Jan  1 01:00:01 kernel: 0x003e0000-0x003f0000 : "config"
    Jan  1 01:00:01 kernel: sflash: chipcommon not found
    Jan  1 01:00:01 kernel: NET4: Linux TCP/IP 1.0 for NET4.0
    Jan  1 01:00:01 kernel: IP Protocols: ICMP, UDP, TCP
    Jan  1 01:00:01 kernel: IP: routing cache hash table of 512 buckets, 4Kbytes
    Jan  1 01:00:01 kernel: TCP: Hash tables configured (established 1024 bind 2048)
    Jan  1 01:00:01 kernel: ip_conntrack version 2.1 (128 buckets, 1024 max) - 344 bytes per conntrack
    Jan  1 01:00:01 kernel: ip_conntrack_pptp.c:init: ip_conntrack_pptp.c: registering helper
    Jan  1 01:00:01 kernel: ip_conntrack_pptp version 1.9 loaded
    Jan  1 01:00:01 kernel: ip_nat_pptp version 1.5 loaded
    Jan  1 01:00:01 kernel: ip_tables: (C) 2000-2002 Netfilter core team
    Jan  1 01:00:01 kernel: ipt_time loading
    Jan  1 01:00:01 kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    Jan  1 01:00:01 kernel: NET4: Ethernet Bridge 008 for NET4.0
    Jan  1 01:00:01 kernel: 802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
    Jan  1 01:00:01 kernel: All bugs added by David S. Miller <davem@redhat.com>
    Jan  1 01:00:01 kernel: FAT: bogus logical sector size 34816
    Jan  1 01:00:01 kernel: FAT: bogus logical sector size 34816
    Jan  1 01:00:01 kernel: NTFS: Unable to set blocksize 512.
    Jan  1 01:00:01 kernel: VFS: Mounted root (squashfs filesystem) readonly.
    Jan  1 01:00:01 kernel: Mounted devfs on /dev
    Jan  1 01:00:01 kernel: Freeing unused kernel memory: 68k freed
    Jan  1 01:00:01 kernel: Warning: unable to open an initial console.
    Jan  1 01:00:01 kernel: Algorithmics/MIPS FPU Emulator v1.5
    Jan  1 01:00:01 kernel: eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.7.0
    Jan  1 01:00:01 kernel: eth1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.7.0
    Jan  1 01:00:01 kernel: PCI: Enabling device 01:02.0 (0004 -> 0006)
    Jan  1 01:00:01 kernel: eth2: Broadcom BCM4320 802.11 Wireless Controller 3.90.7.0
    Jan  1 01:00:01 kernel: device eth0 entered promiscuous mode
    Jan  1 01:00:01 kernel: device eth2 entered promiscuous mode
    Jan  1 01:00:01 kernel: br0: port 2(eth2) entering listening state
    Jan  1 01:00:01 kernel: br0: port 1(eth0) entering listening state
    Jan  1 01:00:01 kernel: br0: port 2(eth2) entering learning state
    Jan  1 01:00:01 kernel: br0: port 1(eth0) entering learning state
    Jan  1 01:00:01 kernel: br0: port 2(eth2) entering forwarding state
    Jan  1 01:00:01 kernel: ating
    Jan  1 01:00:01 kernel: br0: port 1(eth0) entering forwarding state
    Jan  1 01:00:01 kernel: br0: topology change detected, propagating
    Jan  1 01:00:01 kernel: usb.c: registered new driver usbdevfs
    Jan  1 01:00:01 kernel: usb.c: registered new driver hub
    Jan  1 01:00:01 kernel: usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
    Jan  1 01:00:01 kernel: usb-ohci.c: usb-00:04.0, PCI device 14e4:4715
    Jan  1 01:00:01 kernel: usb.c: new USB bus registered, assigned bus number 1
    Jan  1 01:00:01 kernel: hub.c: USB hub found
    Jan  1 01:00:01 kernel: hub.c: 2 ports detected
    Jan  1 01:00:02 kernel: lp0: using parport0 (polling).
    Jan  1 01:00:02 kernel: hub.c: new USB device 00:04.0-1, assigned address 2
    Jan  1 01:00:02 kernel: usb.c: registered new driver usblp
    Jan  1 01:00:02 kernel: printer.c: v0.13: USB Printer Device Class driver
    Jan  1 01:00:02 kernel: hub.c: USB hub found
    Jan  1 01:00:02 kernel: hub.c: 4 ports detected
    Jan  1 01:00:03 kernel: hub.c: new USB device 00:04.0-1.1, assigned address 3
    Jan  1 01:00:03 kernel: usb.c: USB device 3 (vend/prod 0xea0/0x2168) is not claimed by any active driver.
    Jan  1 01:00:04 kernel: usb.c: registered new driver audio
    Jan  1 01:00:04 kernel: audio.c: v1.0.0:USB Audio Class driver
    Jan  1 01:00:04 kernel: SCSI subsystem driver Revision: 1.00
    Jan  1 01:00:04 kernel: Initializing USB Mass Storage driver...
    Jan  1 01:00:04 kernel: usb.c: registered new driver usb-storage
    Jan  1 01:00:04 kernel: scsi0 : SCSI emulation for USB Mass Storage devices
    Jan  1 01:00:04 kernel:   Vendor: KINGMAX   Model: USB Flash Disk    Rev: 2.00
    Jan  1 01:00:04 kernel:   Type:   Direct-Access                      ANSI SCSI revision: 02
    Jan  1 01:00:04 kernel: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
    Jan  1 01:00:04 kernel: SCSI device sda: 256000 512-byte hdwr sectors (131 MB)
    Jan  1 01:00:04 kernel: sda: Write Protect is off
    Jan  1 01:00:04 kernel: Partition check:
    Jan  1 01:00:04 kernel:  p1
    Jan  1 01:00:04 kernel: WARNING: USB Mass Storage data integrity not assured
    Jan  1 01:00:04 kernel: USB Mass Storage device found at 3
    Jan  1 01:00:04 kernel: USB Mass Storage support registered.
    [...]
    Jan  1 01:00:15 kernel: VFS: Can't find ext3 filesystem on dev sd(8,1).
    Jan  1 01:00:15 kernel: MSDOS FS: Using codepage 950
    Jan  1 01:00:15 kernel: MSDOS FS: IO charset cp950
    Dec 18 20:57:17 USB storage: vfat fs mounted to /tmp/harddisk 
    Dec 18 20:57:17 FTP server: daemon is started
    Dec 18 20:57:26 ntp client: time is synchronized to 129.217.131.21 
    Dec 19 00:48:56 kernel: ip_conntrack_pptp.c:conntrack_pptp_help: ctinfo = 2, skipping
    Dec 19 00:48:59 kernel: ip_conntrack_pptp.c:conntrack_pptp_help: ctinfo = 2, skipping
    Dec 19 00:49:05 kernel: ip_conntrack_pptp.c:conntrack_pptp_help: ctinfo = 2, skipping
    Dec 19 03:42:46 kernel: ip_conntrack_pptp.c:conntrack_pptp_help: ctinfo = 2, skipping
    Dec 19 03:42:48 kernel: ip_conntrack_pptp.c:conntrack_pptp_help: ctinfo = 2, skipping
    Dec 19 03:42:49 kernel: ip_conntrack_pptp.c:conntrack_pptp_help: ctinfo = 2, skipping
    Dec 19 03:42:55 kernel: ip_conntrack_pptp.c:conntrack_pptp_help: ctinfo = 2, skipping
    Dec 19 03:42:55 kernel: ip_conntrack_pptp.c:conntrack_pptp_help: ctinfo = 2, skipping
    Dec 19 12:58:03 ntp client: time is synchronized to 129.217.131.21
    [...]
    Greets
    My Stuff: WL-500g, Mapower H31x 10GB HD, Philips Webcam Vesta PRO, TerraTec Webcam PRO, USB Hub

  5. #5
    Join Date
    Dec 2003
    Location
    Russian Federation
    Posts
    8,353
    Mine logs:
    Code:
    Jan  1 03:00:02 kernel: br0: port 2(eth2) entering forwarding state
    Jan  1 03:00:02 kernel: br0: topology change detected, propagating
    Jan  1 03:00:02 kernel: br0: port 1(eth0) entering forwarding state
    Jan  1 03:00:02 kernel: br0: topology change detected, propagating
    So, looks like this a part of propag-ating.

    Try dmesg, it should show kernel messages untouched.

  6. #6
    Join Date
    Mar 2004
    Location
    Europe
    Posts
    32

    dnsmasq and starcraft

    oleg, you're the greatest, this firmware fixed the dnsmasq/starcraft problem for me

    loadsa cheers, thomas.

  7. #7
    What do you mean for USB officejet support?
    Will the built-in scanner work?
    If not, can't you put a deamon to serve direct acess to the USB port?
    I've found a project that we should pay attencion...
    http://usbip.naist.jp/

    This is the solution! We can attach ANY USB device.. printer-scanner combo, serial port converters, anything... RAW access to the USB port...

  8. #8
    Join Date
    Dec 2003
    Location
    Russian Federation
    Posts
    8,353
    Quote Originally Posted by Dante_
    What do you mean for USB officejet support?
    Will the built-in scanner work?
    No, but some models now supports printing via USB.
    If not, can't you put a deamon to serve direct acess to the USB port?
    I've found a project that we should pay attencion...
    http://usbip.naist.jp/

    This is the solution! We can attach ANY USB device.. printer-scanner combo, serial port converters, anything... RAW access to the USB port...
    Yes, but for now it requires linux on the other side.
    Last edited by Oleg; 20-12-2004 at 06:34.

  9. #9
    Yes, and it's in alpha stage yet...
    I'll try to find other projects...

  10. #10
    Join Date
    Mar 2004
    Location
    Europe
    Posts
    32

    wpa-psk with tkip+aes

    since the firmware upgrade my wireless connection in ap mode with wpa-psk (tkip+aes) encryption won't come up anymore.
    only wep is working correctly....

    cheers, thomas.

  11. #11
    Join Date
    Dec 2003
    Location
    Russian Federation
    Posts
    8,353
    Quote Originally Posted by piri
    since the firmware upgrade my wireless connection in ap mode with wpa-psk (tkip+aes) encryption won't come up anymore.
    only wep is working correctly....

    cheers, thomas.
    Please try ASUS 1.9.2.7 firmware and let me know if it works.

  12. #12
    Join Date
    May 2004
    Location
    Netherlands
    Posts
    70
    Hi,

    Great firmware but there is one issue that I had never before.
    When i listen to webradio, the router crashes completely after about 10 minutes. It has a complete reset.
    Computer is connected by wire, so no wireless issues or so.

    The asus 1.9.2.7. has exactly the same issue.

    In previous versions this worked all fine.

    Any ideas????

  13. #13
    (1 days, 5 hours, 34 minutes, 46 seconds since boot)
    without dropping my connection on wire and wirless @ same time

    Great work

  14. #14
    Join Date
    Dec 2003
    Location
    Russian Federation
    Posts
    8,353
    Quote Originally Posted by i-beast-a
    When i listen to webradio, the router crashes completely after about 10 minutes. It has a complete reset.

    Any ideas????
    Yes, buy FM radio.
    In fact - no ideas, seems like something is changed in the kernel. Is it RA translation?

  15. #15
    Join Date
    May 2004
    Location
    Netherlands
    Posts
    70
    Quote Originally Posted by Oleg
    Yes, buy FM radio.
    In fact - no ideas, seems like something is changed in the kernel. Is it RA translation?


    What the F*** is RA translation??

    I've tried several stations but it keeps on chrashing...

    Few examples:
    http://ms.stream.garnierprojects.com/radio538
    http://62.250.12.54:8000/listen.pls
    http://www.c-dance.be/cdance-high.asx

    The rest works great for me...

Page 1 of 4 123 ... LastLast

Similar Threads

  1. Firmware v1.9.2.7 CR2 [Oleg]
    By Oleg in forum WL-500g Firmware Releases
    Replies: 64
    Last Post: 11-01-2005, 18:22
  2. Firmware v1.7.5.9 CR2 [Oleg]
    By Oleg in forum WL-500g Firmware Releases
    Replies: 38
    Last Post: 06-10-2004, 08:12
  3. Firmware v1.7.5.6 CR2 [Oleg]
    By Oleg in forum WL-500g Firmware Releases
    Replies: 37
    Last Post: 05-05-2004, 03:10
  4. Firmware v1.7.5.6 CR2.1 [Oleg]
    By Antiloop in forum WL-500g Firmware Releases
    Replies: 18
    Last Post: 03-05-2004, 11:13
  5. Firmware v1.7.5.6 CR1 [Oleg]
    By Antiloop in forum WL-500g Firmware Releases
    Replies: 15
    Last Post: 07-04-2004, 17:22

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •