Status of IDE support in WL 500 Gx firmware?

**hugo** · 10-11-2004, 20:32

here is /proc/partition:

Code:

major minor  #blocks  name

   3     0    5276880 ide/host0/bus0/target0/lun0/disc
   3     1    5178568 ide/host0/bus0/target0/lun0/part1
   3     2      98280 ide/host0/bus0/target0/lun0/part2

Result are coherent

**hugo** · 10-11-2004, 20:34

ls mod result

Code:

Module                  Size  Used by
usb-storage            62144   0 (unused)
sd_mod                 13268   0 (unused)
scsi_mod               70176   1 [usb-storage sd_mod]
videodev                8304   0
printer                11900   0 (unused)
usb-ohci               21764   0 (unused)
usbcore                77224   1 [usb-storage printer usb-ohci]
ipt_NETMAP               992   0 (unused)
ip_nat_starcraft        2224   0 (unused)
wl                    431504   0 (unused)
et                     23224   1
ide-disk               13524   0
ide-probe-mod          11468   0
ide-mod               109568   0 [ide-disk ide-probe-mod]

**hugo** · 10-11-2004, 21:08

no ext2 support in this firmware: got my first answer. Gotta format a partition using another FS

**hugo** · 10-11-2004, 21:22

dmsg output

Code:

/tmp/harddisk # dmesg
CPU revision is: 00024000
Loading BCM4710 MMU routines.
Primary instruction cache 8kb, linesize 16 bytes (2 ways)
Primary data cache 4kb, linesize 16 bytes (2 ways)
Linux version 2.4.20 (root@omnibook) (gcc version 3.2.3 with Broadcom modificati
ons) #3 Wed Nov 10 22:17:25 MSK 2004
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd init=/linuxrc console=ttyS0,11
5200
CPU: BCM4710 rev 0 at 125 MHz
!unable to setup serial console!
Calibrating delay loop... 82.94 BogoMIPS
Memory: 14088k/16384k available (1611k kernel code, 2296k reserved, 216k data, 6
8k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
NTFS driver v1.1.22 [Flags: R/O]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI en
abled
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Flash device: 0x400000 at 0x1fc00000
Physically mapped flash: squashfs filesystem found at block 1101
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x003e0000 : "linux"
0x001137f4-0x003e0000 : "rootfs"
0x003f0000-0x00400000 : "nvram"
0x003e0000-0x003f0000 : "config"
sflash: chipcommon not found
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 344 bytes per conntrack
ip_conntrack_pptp.c:init: ip_conntrack_pptp.c: registering helper
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
FAT: bogus logical sector size 34560
FAT: bogus logical sector size 34560
NTFS: Unable to set blocksize 512.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 68k freed
Warning: unable to open an initial console.
Algorithmics/MIPS FPU Emulator v1.5
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20265: IDE controller on PCI bus 01 dev 08
PCI: Enabling device 01:01.0 (0004 -> 0007)
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: ROM enabled at 0x000d0000
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
PDC20265: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
    ide0: BM-DMA at 0x0140-0x0147, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x0148-0x014f, BIOS settings: hdc:pio, hdd:DMA
hda: IBM-DADA-25400, ATA DISK drive
ide2: ports already in use, skipping probe
ide3: ports already in use, skipping probe
ide4: ports already in use, skipping probe
ide5: ports already in use, skipping probe
ide0 at 0x100-0x107,0x10a on irq 6
blk: queue c002f2c8, I/O limit 4095Mb (mask 0xffffffff)
hda: 10553760 sectors (5404 MB) w/460KiB Cache, CHS=11168/15/63, UDMA(33)
Partition check:
 /dev/ide/host0/bus0/target0/lun0: [PTBL] [698/240/63] p1 p2
eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 1.3.2.0
eth1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 1.3.2.0
robosw_attach_ocp: no Robo device on OCP bus
robosw_attach_pmii: no Robo switch detected
Robo switch init failed
PCI: Enabling device 01:02.0 (0004 -> 0006)
eth2: Broadcom BCM4320 802.11 Wireless Controller 1.3.2.0
device eth2 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: port 1(eth2) entering learning state
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth2) entering forwarding state
br0: topology change detected, propagating
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
usb-ohci.c: usb-00:04.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
Adpt 2 0
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
Linux video capture interface: v1.00
SCSI subsystem driver Revision: 1.00
Adpt 1 0
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Adpt 0 0
Link up 0 0
Adpt ffffffff 0
ext3: No journal on filesystem on ide0(3,1)
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:01.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:01.
SQUASHFS error: Can't find a SQUASHFS superblock on ide0(3,1)
ext3: No journal on filesystem on ide0(3,1)
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:01.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:01.
SQUASHFS error: Can't find a SQUASHFS superblock on ide0(3,1)
ext3: No journal on filesystem on ide0(3,1)
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:01.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:01.
SQUASHFS error: Can't find a SQUASHFS superblock on ide0(3,1)
ext3: No journal on filesystem on ide0(3,2)
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:02.
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:02.
SQUASHFS error: Can't find a SQUASHFS superblock on ide0(3,2)
hub.c: new USB device 00:04.0-1, assigned address 2
scsi0 : SCSI emulation for USB Mass Storage devices
  Vendor:           Model: USB DRIVE         Rev: 2.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70  6
ASC=28 ASCQ= 0
Raw sense data:0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28
0x00 0x00 0x00 0x00 0x00
sda : block size assumed to be 512 bytes, disk size 1GB.
 /dev/scsi/host0/bus0/target0/lun0: I/O error: dev 08:00, sector 0
 I/O error: dev 08:00, sector 0
 unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
VFS: Disk change detected on device 08:00
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
 /dev/scsi/host0/bus0/target0/lun0: p1
VFS: Can't find ext3 filesystem on dev sd(8,1).
/tmp/harddisk #

Have to find a way to format ext3 or fat without flashing back firmware

**hugo** · 10-11-2004, 21:28

I'm sure it works, I'm going to revert to wl-hdd stock firmware to format the filesystem

**hugo** · 10-11-2004, 21:33

Code:

# cat /proc/pci
PCI devices found:
  Bus  0, device   0, function  0:
    Class 0500: PCI device 14e4:0803 (rev 0).
      IRQ 6.
      Non-prefetchable 32 bit memory at 0x18000000 [0x18000fff].
      Non-prefetchable 32 bit memory at 0x0 [0x7ffffff].
      Non-prefetchable 32 bit memory at 0x10000000 [0x17ffffff].
      Non-prefetchable 32 bit memory at 0x80000000 [0xffffffff].
  Bus  0, device   1, function  0:
    Class 0200: PCI device 14e4:4711 (rev 0).
      IRQ 5.
      Non-prefetchable 32 bit memory at 0x18001000 [0x18001fff].
  Bus  0, device   2, function  0:
    Class 0200: PCI device 14e4:4713 (rev 0).
      IRQ 3.
      Non-prefetchable 32 bit memory at 0x18002000 [0x18002fff].
  Bus  0, device   3, function  0:
    Class 0703: PCI device 14e4:4712 (rev 0).
      IRQ 2.
      Non-prefetchable 32 bit memory at 0x18003000 [0x18003fff].
  Bus  0, device   4, function  0:
    Class 0c03: PCI device 14e4:4715 (rev 0).
      IRQ 2.
      Non-prefetchable 32 bit memory at 0x18004000 [0x18004fff].
  Bus  0, device   5, function  0:
    Class 0604: PCI device 14e4:0804 (rev 0).
      IRQ 6.
      Non-prefetchable 32 bit memory at 0x18005000 [0x18005fff].
      Non-prefetchable 32 bit memory at 0x8000000 [0xfffffff].
  Bus  0, device   6, function  0:
    Class 0b30: PCI device 14e4:0805 (rev 0).
      IRQ 6.
      Non-prefetchable 32 bit memory at 0x18006000 [0x18006fff].
      Non-prefetchable 32 bit memory at 0xff200000 [0xff3fffff].
  Bus  0, device   7, function  0:
    Class 0501: PCI device 14e4:0811 (rev 0).
      IRQ 2.
      Non-prefetchable 32 bit memory at 0x18007000 [0x18007fff].
      Non-prefetchable 32 bit memory at 0x1f000000 [0x1fffffff].
  Bus  0, device   8, function  0:
    Class 0200: PCI device 14e4:4713 (rev 0).
      IRQ 4.
      Non-prefetchable 32 bit memory at 0x18008000 [0x18008fff].
  Bus  1, device   0, function  0:
    Class 0600: PCI device 14e4:4710 (rev 1).
      IRQ 6.
      Non-prefetchable 32 bit memory at 0x40000000 [0x40001fff].
      Prefetchable 32 bit memory at 0x0 [0x7ffffff].
  Bus  1, device   1, function  0:
    Class 0180: PCI device 105a:0d30 (rev 2).
      IRQ 6.
      Master Capable.  Latency=64.
      I/O at 0x100 [0x107].
      I/O at 0x108 [0x10b].
      I/O at 0x110 [0x117].
      I/O at 0x118 [0x11b].
      I/O at 0x6800 [0x683f].
      Non-prefetchable 32 bit memory at 0x0 [0x1ffff].
  Bus  1, device   2, function  0:
    Class 0280: PCI device 14e4:4320 (rev 3).
      IRQ 6.
      Non-prefetchable 32 bit memory at 0x40002000 [0x40003fff].

from stock firmware

**hugo** · 10-11-2004, 21:59

Can somebody help me with a busybox version and instruction to create and format a partition under fat or ext3 filesystem?

Thread: Status of IDE support in WL 500 Gx firmware?

Thread Tools

Rate This Thread

Display

Hybrid View

Similar Threads

Telstra BigPond Heartbeat support added to Oleg's firmware

Development status of customized 1.8.x.x firmware ?!?

Status log & DHCP

Status Log info

Posting Permissions