[HowTo] Install and configure Oleg's firmware

[MrPeeth]

Hi Wengi!

I read errors every where that is why I did not discover the message...
This is the result:

login as: admin
admin@192.168.1.1's password:
[admin@PSQ10 root]$ e2fsck -b 8193 /dev/discs/disc0/part2
e2fsck 1.38 (30-Jun-2005)
e2fsck: while trying to open /dev/discs/disc0/part2

The superblock could not be read or does not describe a correct ext2
filesystem.  If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
    e2fsck -b 8193 <device>

[admin@PSQ10 root]$

The log growth with many error line coz e2fsck...

The workingdir for the transmission is:
/tmp/harddisk/torrent

I can read my datas on part3 in linux, except the /part2.
What do you think about this: delete part2, and start with a new partition and install all programs again?
or save all datas, format and test the whole disc?

Thank:
MrPeeth

[shinji257]

Hello everyone
@shinji257:
Thanks for these tips. I will link it in the howto. I am NOT able to test it....

Not a problem. I actually updated it a little. Mentioned what should be changed if they don't want to use port 2222 and/or 443 for the second server and also dropped in what ps should show if they installed procps. I put in bold a few key lines in the quoted areas.

[wengi]

Hi,

MrPeeth:
reformating and reinstalling part2 should be the fastest way.
But, as i said, i recommend a data backup. Maybe your hdd has a prob....

shinji257
thanks

wengi

[nunbaggi]

Originally Posted by nunbaggi
I have a problem deleting what i download with transmission..
I need admin rights to do it.. How do i get this??

Could you please give us a bit less information...?!?
You try to delete on which way? Samba, ftp, shell, webinterface?
If samba:
Would be nice to know which samba you are using, your config aso

.

-I followed your how too all the way
-i can delete using ftp, or in my computer
-

[MrPeeth]

MrPeeth:
reformating and reinstalling part2 should be the fastest way.
But, as i said, i recommend a data backup. Maybe your hdd has a prob....

Do you mean, only part2 need to be reformating?

Now I try to save all data on a winXP PC.

e2fsck program do bad sector test as well or there is an other linux program what I have to use for test my HDD?

Thanks:
MrPeeth

[wengi]

yep, only part2.

man e2fsck

-> e2fsck -ck /dev/dis.....

wengi

[MrPeeth]

yep, only part2.

man e2fsck

-> e2fsck -ck /dev/dis.....

wengi

Hi Wengi!

Thx for fast reply.
I run a linux recovery on part2.
There are torrent datas in : /opt/share/cgi-bin
There are many files over 40Mb-s. Do I had any wrong settings? That is why my part2 become.
The donloaded torrents are in /tmp/harddisk/torrent/work directory, normally.

I will try to run the bad sector test.

The man command is new for me as well.

Thx again:
MrPeeth

add:
the really big file was: /opt/var/log/message.0 -> 7847Mb
Any idea?

Now I cannot find the part3 in the partiton table...

[wengi]

Hi,

The growing of messages is the result of mixing scripts from my old and new howto.

Make sure that your files in /opt/etc/init.d/ are exactly as in my howto.
If you use an old syslog rc script it will grow your messages file until /opt is full....

If you saved all your data it would be the best to start all over again.

wengi

[MrPeeth]

Hi,

The growing of messages is the result of mixing scripts from my old and new howto.

Make sure that your files in /opt/etc/init.d/ are exactly as in my howto.
If you use an old syslog rc script it will grow your messages file until /opt is full....

If you saved all your data it would be the best to start all over again.

wengi

Thx!

Now part2 is succesfully recovered.
But, part3 cannot discover by any windows prog.
Linux can detect part3 with wrong superblock...
I have some important datas on that partition, so I try to make some more step to save them.
Do you have any idea?
The part3 is almost 150Gb and it was nearly full.

Norton Partition manager said: unpartitionad area.
Ext2FSD discover a partition, but it cannot mount to Vista
I made it like you wrote so it is an ext3 partition, isn't it?

Thanks for all help.
MrPeeth

[wengi]

Yes, it is ext3.
But you normaly use ext2 tools because ext3 = ext2 + journal.

Do some google search for "ext3 recover superblock".
As far as i know ext3 saves various superblocks at differentlocations...

i am not that experienced with file systems...

wengi

[MrPeeth]

Yes, it is ext3.
But you normaly use ext2 tools because ext3 = ext2 + journal.

Do some google search for "ext3 recover superblock".
As far as i know ext3 saves various superblocks at differentlocations...

i am not that experienced with file systems...

wengi

Thanks all.

I will try that you offered.

MrPeeth

[nunbaggi]

I have changed my firmware on wl-500w to the org asus 2.0.01 from oleg version 10.
I have installed Hdd with the guide 4a.
Now i cant find the HDD.
What are the folders called/partions on the HDD called??
What can i do?

[Kubicz]

Hi all gurus,

I applied lots of these configuration to my ASUS fw, what is done by engy from Czech Rep. due to the support for CDMA/HSDPA devices.

Everything works for me, I installed Samba3 and now I'm able to access it on the address of the router on a port 901, but have a serious problem with Transmission, which doesn't work at all.

I applied a step-by-step tutorial from this thread, but my Transmission is probably not running, see my output from "ps axf" below:

PID TTY STAT TIME COMMAND
1 ? S 0:01 /sbin/init
2 ? S 0:00 [keventd]
3 ? RN 0:02 [ksoftirqd_CPU0]
4 ? S 0:00 [kswapd]
5 ? S 0:00 [bdflush]
6 ? S 0:00 [kupdated]
7 ? S 0:00 [mtdblockd]
45 ? S 0:00 telnetd
50 ? S 0:03 httpd eth1
55 ? S 0:00 klogd
56 ? S 0:00 snmpd -c /tmp/snmpd.conf
60 ? S 0:00 [dnsmasq]
62 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan
65 ? S 0:00 [khubd]
74 ? Ss 0:00 lpd
76 ? Ss 0:00 p9100d -f /dev/usb/lp0 0
79 ? Ss 0:00 waveservermain
81 ? Ss 0:00 rcamdmain
85 ? S 0:00 [usb-storage-0]
86 ? S 0:00 [scsi_eh_0]
99 ? Ss 0:00 infosvr br0
100 ? Ss 0:00 watchdog
104 ? Ss 0:00 \_ ntp
113 ? S 0:00 dropbear
1132 ? Ss 0:01 \_ dropbear
1133 pts/1 Ss 0:00 \_ -sh
1218 pts/1 R+ 0:00 \_ ps axf
127 ? S 0:00 udhcpc -i eth1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
144 ? S 0:00 [kjournald]
145 ? S 0:00 [kjournald]
148 ? Ss 0:00 /usr/sbin/vsftpd
186 ? Ss 0:00 [smbd]
199 ? S 0:00 \_ [smbd]
1217 ? S 0:00 \_ [smbd]
188 ? Ss 0:00 /opt/sbin/nmbd -D -n rybarrouter -o -l /tmp -s /opt/etc/samba/smb.conf
193 ? Ss 0:00 /opt/sbin/cron
203 ? Ss 0:00 /opt/sbin/xinetd -pidfile /var/run/xinetd.pid
213 ? S 0:00 /usr/sbin/busybox_httpd -c /opt/etc/httpd.conf -p 8008 -h /opt/share/www
219 ? S 0:00 upnp -D -L br0 -W eth1
533 ? S 0:00 /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7 -s 0

Can anybody help me, where can be a problem?

[wengi]

@nunbaggi
i am not sure if the original firmware will accept the partitions made with oleg and my howto. No experience with this.
Maybe anyone else can help?

@Kubicz
Is the webinterface accessible?
If yes:
- Control if transmission is paused. If yes -> press pause button.
- Press watchdog button to start deamon

wengi

[Kubicz]

@nunbaggi
i am not sure if the original firmware will accept the partitions made with oleg and my howto. No experience with this.
Maybe anyone else can help?

@Kubicz
Is the webinterface accessible?
If yes:
- Control if transmission is paused. If yes -> press pause button.
- Press watchdog button to start deamon

wengi

Well, webinterface is accessible but there is an error:

Unable to find recent transfer stats in syslog

13:02:28 up 18 min, load average: 0.25, 0.67, 0.65

From ps I understood it that transmission is not running, so than I pressed pause button and result is:

touch: /.paused: Read-only file system /opt/share/www/cgi-bin/transmission.cgi: kill: 788: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or kill -l [exitstatus] Stopping transmissison!
Transmission will eventually stop. Last Log line should report transmissiond exiting.


Unable to find recent transfer stats in syslog

13:04:39 up 20 min, load average: 0.02, 0.43, 0.56

After pressing Watchdog it generates:

touch: /.watchdog: Read-only file system BusyBox v1.1.3 (2008.03.30-21:31+0000) multi-call binary Usage: rm [OPTION]... FILE... /opt/sbin/transmission_watchdog: kill: 304: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or kill -l [exitstatus] Usage: transmissiond [options] active-torrents.txt [options] Options: -h, --help Print this help and exit -v, --verbose Verbose level implies foreground (0 to 2, default = 0) -p, --port Port we should listen on (default = 51413) -u, --upload Maximum upload rate (-1 = no limit, default = 20) -d, --download Maximum download rate (-1 = no limit, default = -1) -f, --finish Command you wish to run on completion -n --nat-traversal Attempt NAT traversal using NAT-PMP or UPnP IGD -w, --watchdog Watchdog interval in seconds (default = 600) -i, --pidfile PID file path -e, --encryption Turns on encryption as preferred Signals: HUP reload active-torrents.txt and start/stop torrents USR1 write .status files into torrent directories USR2 list active torrents rm: cannot remove `/.watchdog': No such file or directory
13:06:14 up 21 min, load average: 0.07, 0.32, 0.50