Search:

Small guess... reset to defaults? :)

Yes and no. Yes because the Asus Wl500g is capable of being a router without using NAT/PAT. (System Setup - Operation Mode => select "router")

Unfortunately for you this is useless. If you have 5...

Like Wiz says, PPTP should be no problem. But if you use L2TP then the server must support NAT traversel, of not, you're out of luck I'm afraid....

Do you know which protocol of client your father...

I've got it like this, and it's working. (currently using 1.9.2.7-2, with 1.8.x.x is was also working)

I think you should also add 4673 (both tcp and udp) for kademlia to work.... (or is that not your problem?)

Just tried, and it works :) (not that I really care, I'm the only one here around with WiFi so I have enough channels to choose from :)) But great work!

This sounds like the big "wan port dies" issue a lot of people had. For me the solution was fixing the wan port at 100 mbps half duplex. Also a lot of people here reported that the new Asus beta...

I'm running firmware 1.8.1.7-2 and I'm also not able to select channel 12 or higher. (time zone set to GMT+1) I haven't tried firmware rev 3.....

Just to let you know :)

Edit: just tried, same...

Maybe you are a bit confused with classless interdomain routing? (CIDR) Unfortunately like Oleg says, this does not give you any security advantage at all.

Yes, that is possible :) You can connect to the other computers just by using their IP addresses. (i.e. \\192.168.10.10 )

If you want to be able to browse to all computers, you'll need a WINS...

Believe me, it really isn't that easy.

There are a few reason's why WEP could be easy to crack. The first is the authentication protocol if you use "shared key" for authentication. Basically the...

How did you try to update the firmware? Browser or Firmware recovery? If you use the firmware recovery program and you are using XP SP2, don't forget to shutdown the SP2 firewall....

On your Windows machine, press start -> run -> type "cmd" press ok then the commands Oleg told you :)

In the Asus configuration manager -> wireless -> bridge, if you look at the picture when selecting AP mode you see a single AP if you select AP only. But if you select WDS only, you see 3 segments...

Absolutely true :) But I think it's fun to have it all working, that's all..... Besides it could be pretty usefull for small companies with small branch affices to have a cheap VPN solution. A Cisco...

Thanx :D


Too bad :) I was hoping someone already tried to use the Asus AP as a client like the Cisco 3002 hardware client. I already checked but unfortunaly the pppd doesn't have MPPE support,...

A bridge is a connection between 2 network segments. I've never tried to use an Asus AP as a bridge, so I don't know much about it.

But if all AP's are connected to the router by a LAN cable then...

To be able to browse the network on a single segment you need a browse master. Usually the most "powerfull" Windows version is elected as the browse master. (check your event log, you will see...

Ok great! Can't wait to try it....

Could you define "a bit" :)

The first log entry is caused by "File and Printer sharing." 139 is used by the computer browser service running on your computer. It propably just wants to scan your network for other computers. As...

Printing is compatible with HP Deskjet 930C which is on the supported printers list, so I assume printing should work.

I assume you are using WinXP SP2? Because with SP1 port 5000 is used by SSDP (Simple Service Discovery Protocol). WinXP SP2 and future releases should use port 2869 for SSDP.

I think there is no...

Setting the same channel on all AP's is not a good idea. (in fact it's wrong :D ) A channel represents the center frequency that the AP uses, channel 1 uses 2.412 GHz, channel 2 uses 2.417 GHz. A...

It's not a problem to have more than just one DHCP servers on a single segment, as long as they don't have overlapping IP ranges. So if the first DHCP server gives away IP addresses from e.g...