Search:

Type: Posts; User: dolphine

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    13,757

    root to hda1 on Backfire

    I have succesfully flashed Bacfire image onto my WL700, but I can not fid a way to change root to hdd :-(

    Though I can see both partitions mounted

    /dev/hda1 to /mnt/hda1

    /dev/hda3 to...
  2. Replies
    2
    Views
    2,578

    Please see post...

    Please see post http://wl500g.info/showpost.php?p=114103&postcount=2 for compiled version of the igmprpxy and udpxy. However no luck with getting them work on my WL700.
  3. Replies
    2
    Views
    4,087

    Update: Finally got some spare time and got udpxy...

    Update: Finally got some spare time and got udpxy and igmpproxy compiled.

    Both seem to be running, except that I just can not make them work.

    I get either resource not available or protocol...
  4. Replies
    2
    Views
    4,087

    udpxy - will it work & compiled version

    Hello,

    has anybody successfully tried udpxy for RDP/multicast to http/streaming?

    Unfortunately I am not even able to compile :-( getting segmentation fault or permission denied when compiling....
  5. Replies
    27
    Views
    11,458

    Some time ago when I used to test if the spindown...

    Some time ago when I used to test if the spindown works I have had this in my crontab :



    /opt/sbin/hdparm -C /dev/ide/host2/bus0/target0/lun0/disc | grep "drive state" | /opt/bin/logger

    ...
  6. Replies
    4
    Views
    2,088

    Sorry for off-topic, but I could not resist :-) ...

    Sorry for off-topic, but I could not resist :-)



    Any chance you will enable multicast support in the "basic" image?
    I am extremely satisfied with my (your :-) + several thinks like syslog-ng,...
  7. Replies
    3
    Views
    2,233

    Thanks a lot! I did not think of the the...

    Thanks a lot!

    I did not think of the the original df (/bin/df), which works fine, so I can check the space on the HDD which was the original intent.





    [root@(none) /opt/bin]$ ls -la *df...
  8. Replies
    3
    Views
    2,233

    df vs /etc/mtab

    Hello,

    recently I have found that df is not working well as it can not find /etc/mtab

    When I try to specify the volume it says that it can not find the mountpoint

    Unfortunately /proc/mounts...
  9. Replies
    115
    Views
    81,331

    Thank you very much in advance.

    Thank you very much in advance.
  10. Replies
    115
    Views
    81,331

    Thanks - at least I know that "playing" will not...

    Thanks - at least I know that "playing" will not help and if I want to make it work I have either to:
    - start with openwrt
    - build new kernel
    which is both more time consuming than I can invest...
  11. Replies
    115
    Views
    81,331

    Perhaps question to different forum, but also a...

    Perhaps question to different forum, but also a wish related to the new firmware image.

    Does the current FW kernel have multicast support enabled?

    Would it be possible to include it in the next...
  12. Replies
    0
    Views
    6,184

    How to enable UDP multicast through NAT

    Hello networking gurus,

    after some playing and reading stuff on TCP/UDP/IGMP/IPtables with no success - I am asking for an expert advice:

    My ISP provides free IPTV service. However as they are...
  13. Replies
    272
    Views
    101,398

    Thanks a lot! I was confused by the result of...

    Thanks a lot!

    I was confused by the result of hdparm -I ... and -C which just says suspend :-(
  14. Replies
    16
    Views
    6,855

    I think that local prot should be 22 as well....

    I think that local prot should be 22 as well. Port range specifies the range of port on external (WAN) interface that are forwardded to local ip and local port. Therefore both ports shoudl be 22. The...
  15. Replies
    272
    Views
    101,398

    Strange things happen - if I set it the way you...

    Strange things happen - if I set it the way you describe, the hdd goes standby in few minutes (i hear the sound of going standby and hdparm -C /dev/... says suspend) and i hear the same when I wake...
  16. Replies
    4
    Views
    5,428

    Some settings are defaulted in web-gui, others...

    Some settings are defaulted in web-gui, others you should be able to modify over the iptables



    iptables --list
    iptables -d nat --list


    See documentation...
  17. Replies
    16
    Views
    6,855

    K.C., is there a special reason to have it in...

    K.C.,

    is there a special reason to have it in nat table in addition to input?

    Thanks & Rgds
  18. Replies
    16
    Views
    6,855

    You can open port 22 in Asus WEB-GUI - this is...

    You can open port 22 in Asus WEB-GUI - this is probably the easiest way that will also work after you restard the router.

    - or your can open it manually by e.g.


    iptables -I INPUT 7 -p tcp ...
  19. Replies
    28
    Views
    40,538

    I'm not downloading that much to check - but I...

    I'm not downloading that much to check - but I suspect that utorrent DHT feature makes the difference (it sees much bigger number of peers). As my line speed is 10Mbit symmetrical it can boost the DL...
  20. Replies
    2
    Views
    1,946

    Several threads discussing this topic - with...

    Several threads discussing this topic - with similar/same questions.

    Perhaps we could go on with the firewall setup in http://wl700g.info/showthread.php?t=7749
  21. Replies
    7
    Views
    3,404

    rc.local will work, but - any change in router's...

    rc.local will work, but
    - any change in router's confiiguration over the web UI will make it reset the network configuration not taking care of the any further settings irregardless ehre they are...
  22. You can set them and some other things .profile...

    You can set them and some other things .profile in your home directory
  23. Replies
    28
    Views
    40,538

    Isn't it better to OPEN the ports to your WAN...

    Isn't it better to OPEN the ports to your WAN address than to forward them to the LAN?

    see my other post in iptables topic, but generally
    iptables -I INPUT 7 -p tcp --dport 2700:2710 -j ACCEPT ...
  24. Replies
    2
    Views
    3,777

    Findings & current set-up

    Hello,

    unfortunately I do not have much time to play with the device :-(. As I am also a self-learner in the area of linux, scripting, routing, etc. I no not have the patterns to do this right -...
  25. Replies
    2
    Views
    3,777

    iptables set-up

    I was playing with the iptables setup in order to open the ssh port to outside world and could not get out, how to make sure that the firewall web-gui does not interfere with my settings.

    Have any...
Results 1 to 25 of 27
Page 1 of 2 1 2