Search:

Type: Posts; User: rogerrb

Search: Search took 0.01 seconds.

  1. Replies
    33
    Views
    27,582

    I've been running OpenVPN on a WL500gx (32 MB...

    I've been running OpenVPN on a WL500gx (32 MB RAM) for some years from a USB stick, and on a WL500g (16 MB RAM) before that. On the WL500 gx i'm not using any swap memory when openvpn is running,...
  2. Replies
    38
    Views
    45,994

    I tried to upgrade again, and changed my channel...

    I tried to upgrade again, and changed my channel from 13 to 12, since then the wireless has been stable for 7 days now as long as I use a laptop with Atheros wireless card, but the connection from a...
  3. Replies
    38
    Views
    45,994

    I have the same problem after upgrading my WL500g...

    I have the same problem after upgrading my WL500g Deluxe. After 11 hours the wireless network became unstable. The wired connections were stable and there was no entries in the syslog indicating any...
  4. I think you have to add the wlan interface to the...

    I think you have to add the wlan interface to the bridge. I have a WL500gx, so the name of the interface may be different on your WL500g (I think it may be eth0 or eth1, on my WL500gx it's vlan1).
    ...
  5. Replies
    10
    Views
    2,794

    I'm using Oleg's 7e firmware.

    I'm using Oleg's 7e firmware.
  6. Replies
    10
    Views
    2,794

    I'm getting 95 Mb/s wired, I have never bothered...

    I'm getting 95 Mb/s wired, I have never bothered to measure Wireless accurately but I think I'm getting between 8 and 12 Mb/s on Wireless transfers.
  7. Thread: ushare

    by rogerrb
    Replies
    6
    Views
    12,376

    I'm not sure you have to disable uPNP in the web...

    I'm not sure you have to disable uPNP in the web interface. I am running ushare with uPNP enabled and have modified the file /opt/etc/ushare to look like this:

    # /etc/ushare.conf
    # Configuration...
  8. Replies
    2
    Views
    2,832

    Post-firewall is the script for firewall rules

    The firewall- and forwarding-rules are deleted whenever the DHCP-lease from you ISP is renewed/changed. When this happens, the /usr/local/sbin/post-firewall script will be run by the router.
    You'll...
  9. Replies
    195
    Views
    143,732

    Openvpn installation

    To install Openvpn you should use the following command:
    ipkg -force-depends install openvpn

    You should also read this thread and the howto the thread is referring to:...
  10. Replies
    195
    Views
    143,732

    Openvpn installation

    To install Openvpn you should use the following command:
    ipkg -force-depends install openvpn

    You should also read this thread and the howto the thread is referring to:...
  11. Replies
    4
    Views
    3,680

    You could install Oleg's custom firmware, and...

    You could install Oleg's custom firmware, and install OpenVPN on a USB memory stick. I'm using it to connect 2 sites and 3 roaming users. The only disadvantage is that I'm only able to pusg 1,5 Mb/s...
  12. Replies
    4
    Views
    2,242

    I've located the fault. It's the PC itself. I was...

    I've located the fault. It's the PC itself. I was using my laptop to test the other router, Teamspeak works perfect from the laptop with both the WL500g and my cheap router, and my other PC just...
  13. Replies
    4
    Views
    2,242

    The filters was enabled, I've disabled them but i...

    The filters was enabled, I've disabled them but i still get the same error message: "[20:25:24] No reply from server Maybe the server is offline or maybe teamspeak is not running on it".
    So I'm...
  14. Replies
    4
    Views
    2,242

    Teamspeak RC2 Client

    Hi.
    Are there anyone who has been able to successfully use the Teamspeak RC2 client through the WL500g? I'm unable to connect to any server on the internet, it almost looks like the WL500g is...
  15. Replies
    7
    Views
    3,105

    I think you need 2 subnets of IP addresses. One...

    I think you need 2 subnets of IP addresses. One for your internal PC network, and one for the network you are connecting your router to. It may be possible to utilize the adresses you've already got...
Results 1 to 15 of 15