Search:

Type: Posts; User: 3chansen

Search: Search took 0.02 seconds.

  1. Replies
    263
    Views
    242,440

    Sticky: No usb hardwired out of chip??? Maybe it's still...

    No usb hardwired out of chip??? Maybe it's still mod-able??? Here are the pics just in case. Let me know which resistors you need to know the resistance of, cause it's still kinda hard to read.
    ...
  2. Replies
    263
    Views
    242,440

    Sticky: Script for coding MAC??

    I will try using the altered windows debrick utility Disq posted, and shorten my cable to 6" (currently 24"), that could have been one reason why I wasn't getting pwr to the par port--(FFFFFFFF) cpu...
  3. Replies
    263
    Views
    242,440

    Sticky: That is what I did. My pins WERE numbered...

    That is what I did. My pins WERE numbered incorrectly on my db25, so I made my cable to look exaclty like the one in the photo from the debrick guide. I will double check connections at jtag. BTW,...
  4. Replies
    263
    Views
    242,440

    Sticky: my ID I get is FFFFFFFF (ie all ones, 32 of em)...

    my ID I get is FFFFFFFF (ie all ones, 32 of em)
    but...that is ONLY when loading 2.4 kernel and running under su (root)
    When running under su in 2.6, I get
    Failed to lock /dev/parport0: No such...
  5. Replies
    263
    Views
    242,440

    Sticky: My cable is almost exaclty 25 inches also. the...

    My cable is almost exaclty 25 inches also.
    the cpu id I was getting was the exact same as if it wasn't plugged in at all.
    I will try again, playing with the timing and trying to remove the resistor.
  6. Replies
    263
    Views
    242,440

    Sticky: no cpu detected

    It didn't detect the CPU. It listed possible causes, and one was a different chip version on the WRT54g. My cable was wrong at first (flipped from left to right), then I made it right. It's...
  7. Replies
    263
    Views
    242,440

    Sticky: Chupa will take off where M$ left it [to die] my...

    Chupa will take off where M$ left it [to die]
    my sentiments exactly! They could have at least added functioning AP client mode to the list of to-do's.
    As for custom firmwares, I think the Asus...
  8. Replies
    263
    Views
    242,440

    Sticky: Why not? All you need is a usb port(chips are...

    Why not? All you need is a usb port(chips are the same), and maybe some minor mods. I remember reading the BCM4702 nativley supports USB. It might be as simple as soldering four wires to the board...
  9. Replies
    263
    Views
    242,440

    Sticky: might be my parallel port

    What tests can I run in Knoppix to verify my parallel port is running?
    No lp module is loaded. After updating cable to match Sveasoft's, I get the same error (and the pwr WAS on the router). ...
  10. Replies
    263
    Views
    242,440

    Sticky: update... cable updated. It looks like his now....

    update...
    cable updated. It looks like his now. It will take too long to try it tonight, I'll wait till tomorrow. (can I cancel it if it begins to read the flash?)
  11. Replies
    263
    Views
    242,440

    Sticky: hmmm...

    Got past the weird port error, but now...
    Cable problemo...

    According to this...
    http://scatcat.fhsu.edu/~cmhansen/diag.jpg ...
  12. Replies
    263
    Views
    242,440

    Sticky: Will do

    I wonder why knoppix ran just "wrt54g" fine under the knoppix user, as I didn't have to typ ./ infront. Well, I knew it had to be something stupid. I will try that and let you know where I get...
  13. Replies
    263
    Views
    242,440

    Sticky: Close...

    Good point on device access/ 1p module. I will try to disable the module if running.

    Is that what is causing "file not found" when I try to run the exe under root?
    It runs ok otherwise. (but no...
  14. Replies
    263
    Views
    242,440

    Sticky: Some progress...

    Thanks for steering me clear of Cygwin for this project! The "make" command was absent from cygwin (or I wasn't using it right???). I compiled the source without a hitch in Knoppix, and ran it...
  15. Replies
    263
    Views
    242,440

    Sticky: installing package

    Thanks for the link to the pdf!

    I am trying to run the wrt54g flash tool on windows under Cygwin, but I can't figure out how to compile it. I don't know much about Linux either, that is why I was...
  16. Replies
    263
    Views
    242,440

    Sticky: Software...

    I have the cable made, but have been looking for easy to use, compatible software. What JTAG programs are best for the BCM4702? For Windows?
  17. Replies
    263
    Views
    242,440

    Sticky: maybe this jtag cable 'll work??

    http://openwince.sourceforge.net/jtag/iPAQ-3600/

    Scrolling down through the article, the hack got this simple cable to work on his ipaq. Of course, my JTAG is 12pin, not 10pin. I assume the...
  18. Replies
    263
    Views
    242,440

    Sticky: Saving firmware

    I don't know what kind of pinout the jtag has...could you point me to a site that gives the pinout? I assume I just have to solder a DB-9 cable to the jtag header with the right pinout. If you...
  19. Replies
    263
    Views
    242,440

    Sticky: Microsoft MN700 hack project

    I have been looking for a custom firmware for this router...but haven't found anything on the net! Microsofts firmware for this thing SUCKS! But I think it could be an awesome router with the right...
Results 1 to 19 of 19