Possible that the partition table is out of order, try Partition Table Doctor 3.0
and scan the disk. If this does not help you i would suggest GetDataBack for FAT. A great program for recovering...
Type: Posts; User: Phantome
Possible that the partition table is out of order, try Partition Table Doctor 3.0
and scan the disk. If this does not help you i would suggest GetDataBack for FAT. A great program for recovering...
I have been sitting some hours working with bridging this two.
What i have know have is a WL500gx connected to internet in home gateway mode.
The Wl500g is connected as ethernet bridge. Wl500g...
What speed did you expect to see and what speed did you get.
For the WL-500g last time i tested i got around 4500kB/s which is
acceptable due to hw limitations
Just got my self a wl500gx and have been using it with v1.9.2.7 CR5a and booting it with a usb stick. Then i upgraded to firmware v1.9.2.7 CR6a and now i can't find the usb stick. /dev/scsi is no...
Better late than never, now available in Norway at
Komplett
After changing the ip_conntrack_max to 4096 it works for a few minuts to half an hour, after that it has been resett to 1024. This happens if i put it in the post-boot script or if i do it manually.
You missed a >
in
echo '#!/bin/sh' > /usr/local/sbin/post-firewall
should be
echo '#!/bin/sh' >> /usr/local/sbin/post-firewall
you can check this by typing
cat /usr/local/sbin/post-firewall...
:rolleyes: Sorry about that, something is disturbing the signal, changed the channel and everything is ok for now. Even the speed changed from 150kbyte/s to 2500kbyte/s :)
Firmware v.1.9.2.7 CR1 [Oleg]
I have got a problem with my wireless connection.
It gets disconnected every short while.
The wireless computer got a static ip.
This is som of the output from...
I'm getting this message when i'm trying to run wshaper on this firmware :
wshaper start "eth1" 680 90
RTNETLINK answers: Invalid argument
.
.
.
Have search for this error and i only...
The only thing without a webinterface is the samba part.
(not sure if you have to make a partition on the usb drive with ext2/3 filsystem or not)
Anyway, by searching this forum i think you will...
Type \\192.168.1.1 if thats your ruter ip in start -> run , it's not always that windows finds the shared folders that are on your network.
got it working :) but was misslead by your $1 (/init/wshaper start "$1" 1000 220) , after changing that to eth1 it's up and running.
i can't get wondershaper to start, seems like there is something wrong in the
config file. I'm using 1.7.5.9-4 rootfs
running /init/wshaper start gives me this error
Cannot find device...
For the open ports part check this thread:
http://wl500g.info/showthread.php?t=425
Check out this thread
http://wl500g.info/showthread.php?t=414&highlight=table+full
PS! There is a search function in this forum ;)
I don't know.. but just test it
Have you checked that you have forwarded the passive mode ports ?
I had to do this. Because the ftp-server program by default "grabs any free port" for passive mode, you might have to tell...
I have done it this way.
This is how it's setup.
Connect the computer with the modem to the WAN port of the router, then setup the router as Home Gateway.
modem/nic -> WAN-|WL500g|-LAN ->...
192.168.1.1 is an internal ip. 192.168.x.x is not routable on the ruters on inet.
you need to find the ip the wan port is using.. the one your getting from the ISP if you want people outside to...
As for the printer:
http://uk.asus.com/products/communication/wireless/printer-support.htm
That's the list of compatible printers from asus. You should also check out >Reported Compatible...
NP... i search for the error and here is the result
http://www.busybox.net/lists/busybox/2002-December/007582.html
Think this will help
Does not work here either
ping: my.router: Resolver Error 0 (no error)
Think it's stupid from ASUS side to say that the WAN port is 10/100Mb when you can't get more than around 40Mb.
"Seems, you've a broken device on the other side of the link."
If you meen it's the...
I have one question regarding the custom firmware.
Is there any command in the telnet session that i can use to edit files on the router? Couldn't find one when i was playing around