Du kannst auch wenn du dich etwas mit Linux auskennst die Bridge herausnehmen.
Dann kannst du das LAN Interface und das W-LAN Interface mit seperaten IP-Bereichen versehen und das Routing so...
Type: Posts; User: Holli
Du kannst auch wenn du dich etwas mit Linux auskennst die Bridge herausnehmen.
Dann kannst du das LAN Interface und das W-LAN Interface mit seperaten IP-Bereichen versehen und das Routing so...
So wie ich das gelesen habe ist dein Modem eigentlich selber schon ein Router mit integrietem Modem. Der Asus kann und brauch sich somit nicht selber in das Internet einwählen.
Um über W-LAN in das...
Ich schätze mal du willst deinen Access Point als "reinen" Access Point nutzen. So das du keine zusätzliche Firewall hast und keine extra Netzwerke.
Für diesen Fall aktiviere den Operation Mode...
It is permanetly.
Did you use NAT? When yes, you must route some ports through the router.
Ich sehe schon den Fehler!
Der Asus Router hat kein integriertes Modem (währe mir auf jeden Fall neu falls der gx eins hätte). Und die FritzBox hat ein integrietes Modem!
Also brauchst du ganz...
Wenn noch nicht mal die WAN-Lampe an geht, dann kontrolier mal das Kabel ob du nen Cross Over oder nen normales hast! Tausch die einfach mal untereinander. (Also wenn de nen normales hast setzt mal...
Webinterface >>> Wireless >>> Advanced >>> Enable Radio >>> No
Reset the router with the hardware reset button. After this you can connect to the router. The same problem I had after the upgrade!
In what directory is the configuration file saved from the snmp server.
I reset the complete AP and upgrade the fimeware again. Then all works.
Thanks for the SNMP Support @ Oleg
Hello
After I upgrade my AP to the 6c-pre5, I have the problem that I can`t login over the webinterface. From all Networks (Wan, Lan, Wireless) I become the message "Connection refused".
All...
An was für einen Router hast du die Festplatte angeschlossen? WL500g oder 500g Deluxe??
Denn der WL500g hat nur USB 1.1 und da wirst du nicht ganz viel mehr schaffen.
Hello
To find out the mac adress you must login you at the AP (telnet or ssh). Then you run the command 'ifconfig' and look for the HWaddr of eth2. That is the mac adress.
Remove your hardisk and printer, and test then if it works.
Then add you step by step all your devices, and look when your AP become`s the problem.
Trasfer you the file from a wlan pc to a wlan pc, or to a computer in the "normal" lan?
What is with the signal?
When I look in my router log`s, every day I can find entries with this error. I think the computer in canada have a virus, and he try to damage other system`s (like windows ?).
Have somebody the information where I can buy the VP100, and how much it cost?
Test the webinterface with the mozilla or firefox browser.
I had the same problem with the IE, (but with a proxy not with a router and with an other browser it works)
Look here:
fast mirror: http://files.wl500g.info/asus/custom/phedny/1.9.2.7-3b+ipv6+cipe/WL500g-1.9.2.7-3b+ipv6+cipe.trx
http://www.p-bierman.nl/~phedny/WL500g-1.9.2.7-3b+ipv6+cipe.trx
What can I do with the halt command?
When I`ll turn off the AP, I cut the power source!
He phendy
Perfect work!!
Update no probs!
Here a short help to setup ipv6.
Login to the AP via telnet or ssh. Then enable forwarding ( echo 1 > /proc/sys/net/ipv6/conf/all/forwarding )....
First question: Why would run an eggdrop at the AP? (It have a not really good CPU, and not enough disk space without an external drive)
The next problem is, you can`t compile on the access point,...
He Antiloop
I`m not Phendy, but I test the IPv6 connection to the forum.
And it works. You can see it in your log`s!!
Tested: WORKING
Model: WL-500g
Firmware: 1.7.5.6-5 (Oleg)
Device
Brandname: Kingston
Brandtype: P/N: KUSBHS2/1024
Flash Memory: 512MB
USB Interface: USB 2.0 compliant
URL To manufacturer:...