Search:

BTW on my WL-500g this command works:

brctl stp br0 disable
And you can check the status:

brctl show br0 stp

You can try to connect the printer to PC, print something and then to reconnect it to router. Perhaps it will work until you power off the printer or until some error condition occurs (paper out...

Don't forget to temporarily stop the personal firewall on your laptop. Also reset router to defaults before update.

You always have a choice. ;) Our choice is to break limits...:)
I have USB hub as well but I usually need only 2 USB ports. One port is dedicated to USB flash key in my case - now I can put it...

You can use almost any coil type, it's not a critical part - the reason is to eliminate interference. D.C. resistance of the coil should be max. 0.1 Ohm.

No special device required. Just some devices might be incompatible so you need to test it. In most cases everything works fine, even some 2.5" low power devices can be powered by router's USB port...

OK then... So this is a (perhaps) more clear "how to".
Router board version needs to be 2.xx as older boards have a different layout.
Good luck!:)

Just copy to some directory and run... USB flash disk preferred.

I have tried the same in Hyperterminal - no luck. I don't say Hyperterminal is bad but... :rolleyes: Strange anyway. Perhaps changing default ttys0 parameters could be the right way.

Please don't try to do it if the info above is not sufficient for you. Onboard parts that you need to solder on are quite small and without some experiences you may permanently damage the router....

Did you try to search forum? ;) You should find a link to compiled (a bit old but perhaps still working) busybox v1.00-pre5. Try the attached file.

No - it seems that Kernel is not able to receive bytes from UART correctly (input - it looks like MSB is corrupted - sometimes - and incorrectly recognized as logical H). Output seems to be OK in any...

Perhaps you have an ADSL modem which supports NAT / firewall as well. So there's one address translation performed by ADSL modem (-->10.0.0.x) and second address translation performed by Asus...

It seems your Internet provider does not give you an external address but keeps you hidden behind NAT ==> 80.229.148.13 address is your provider's gateway.

Thanks! :)
I can confirm that your schematic diagram is OK.
As soldering on small onboard SMD parts is a bit difficult, I prefer using external resistors.
I am getting 5V from the input...

Yes it's possible at least with WL-500B/G using mainboard revision 2.x.
No additional chip required.
http://wl500g.info/showthread.php?t=3571&page=2

wtzm, could you please correct the image a bit?
I believe that USB2 pins should be interchanged ==>


----- ____
USB1_N --I I--|GND \_
USB1_P --I I--| ---
USB2_P --I ...

Please use SEARCH function and you should find it.

It should work fine without any change. Perhaps there's some incompatibility between webcam/hub. Try to reboot the router with connected webcam. Try to unplug/plug in the webcam while the router is...

Didn't you try to set the port speed to fix rate (100mbit)?

I am afraid it's not possible on WL-500B/G as the WAN interface is a separate chip and LAN chipset does not support VLANs. AFAIK you could do it on WL-500GX only.

Try 13,0MHz XTAL then...:) In fact I am using 12,288 MHz and it works fine as well. Please note 5% difference is perfectly OK in any case.

Sorry for the late response... :rolleyes:
The original source was in some discussion about WRT54G. I expected that the same frequency could work in WL-500 as well --> true. If you use different...

Please note that router does not need 2A in fact. It is a max. value including an USB device attached to USB port of Asus. 5V is excellent as you can supply Asus from USB port of PC / laptop (a...

Find and check the data sheet for your specific chip then...
The top frequency limit is important. I am sure the UART chip will work fine at any lower frequency.