WL500gx ingezet. Ik had eerst wat problemen met de routering. Ik kon van mijn netwerk wel naar die van mijn achterburen (kreeg ook ping replies en kon via rdp inloggen), maar mijn achterburen kwamen...
Type: Posts; User: Krypt
WL500gx ingezet. Ik had eerst wat problemen met de routering. Ik kon van mijn netwerk wel naar die van mijn achterburen (kreeg ook ping replies en kon via rdp inloggen), maar mijn achterburen kwamen...
Nou; dat werkte niet.
En met bridges gaan stoeien heb ik niet zo'n zin in.
Ik kan een wl500g deluxe krijgen; krijgen wat die doet.
Van de week nog een klooien met een linksys
brctl werkt wel. In de huidige opstelling bestaat er een bridge tussen wds0.1 wds0.2 en eth0.
Dit betekend dat het WDS netwerk (mijn kant) gebridged is aan de LAN poorten.
Als ik de eth0 kan...
Fixed speed helpt ook niet. Tenminste 100Mbit Fdup knalt er ook uit.
Toen we eerste de WAN port die problemen hadden, een jaar of 4 geleden, toen kon ik nog overweg met 10Mbit. Maar aangezien we...
Fixen van poort levert niets op. WAN klapt nog steeds dicht.
Heb tevens de "Track Connections" omhoog gegooid; dat helpt wel en kan flink wat meer data er doorheen gooien, maar dan knalt ie na 8GB...
Ik heb een WL500g in routing mode via WDS aan een andere WL500g gekoppeld.
Nu blijft de WAN poort maar dicht klappen van deze WL500g in routing mode.
Het rare is dan ik vanaf de andere WL500g...
Het blijkt dat echt de WAN poort dicht klapt.
Ik kan vanaf mijn 192.168.1.0 netwerk de 192.168.1.3 (over de WDS link naar 2e WL500g) gewoon pingen. En ik kan de WAN kant (192.168.2.9) vanaf mijn...
Ik heb een issue met 1 van mijn WL500g's. Ik gebruik ze niet echt op een manier dat de meeste zullen gebruiken, dus ik leg de situatie even uit.
Ik heb een netwerk in de range 192.168.1.0/24. Hier...
When disconnecting the power of the WL500g, my computer looses it's network connection en thereby releases it's IP... When powering up the WL500g in restoration mode, the connection comes up again...
Strange.. I was certain that I had a APIPA address before I could restore the old firmware.. But heck; maybe my computer just had a valid ip just before flashing.. didn't check during flash which ip...
user: empty (do not fill in anything)
pass: admin
Should do the trick..
And for the firmware restoration; I had the same problem when flashing back to 1.7.5.6..
I saw it was working when my...
Ok.. an update..
10half works like a charm.. 10full,100half and 100full doesn't seem to work.. the complete WAN connection doesn't come up..
Flashed the latest firmware 1.8.1.3, but still has the...
Did you have 1.8.1.1 before you were upgrading to 1.8.1.3? I assume you have..
Try the firmawe restauration method to flash it back to 1.7.5.6 and than up to 1.8.1.3..
With the 1.8.1.1 firmware...
Have you tried to reset the router with the restore switch on the back of your router?
If that doesn't work try the Firmware restauration method to restore your old firmware..
GJAman; I tried both 10Mbit halfduplex and 10Mbit fullduplex.. and after a day, my wan is still functioning.. I'll put the speed back to 100Mbit halfduplex this evening and will try again.. if it...
Because I couldn't reproduce it and I needed my internet connection I decided to begin with 10MbitHduplex and raise it while it's still working..
I need to write things down. Didn't do what I...
I'm happy to report that my connection is still up..
I resetted my router to autosensing yesterdag evening and it froze a couple of hours later. This morning I resetted my router and put it on...
Nope.. not annoying.. Just like it as it is :)
Ok.. I'm home now and removed my hub and connected my WL500g directly onto my modem.. Transferred 2 Linux images at the same time; Emule and downloaded a 100MB test zip and my WL500g died in a matter...
Antiloop; could we combine some testing?
You can contact me at my ICQ/MSN..
First I'll try to reproduce the WAN-die with a direct connection, and then try the same with the hub connected. And...
And that person would be me, GJAman :)
I'll try your solution today and will report my findings on both GoT and here.
For the persons who cannot read dutch, a quick story in english.
I've got...
How is your host connected to the Asus WL500g?
My machine was plugged into the first LAN port of the router when I used the Firmware restauration..
I've flashed my router with the beta firmware but missed the print support in Oleg's firmware.. And I successfully flashed back to Oleg's firmware with the Firmware restoration tool.
I first...