Search:

Hi guys,

I recently have bought a NEUROS OSD linux based multimedia player. This player doesn't have DVD drive, it only reads from various memory modules and has network and usb 1.2 connection...

Hi,

If you want to use your asus as a client, you don't need wds mode. You need ap only mode. And if for some reason you need wds then all routers involved must be wds capable. I also run my...

Hi,

There is a status page in the menu on the left side. Check if your asus got an IP address by your other router, because a successful wireless connection doesn't also mean that your asus got an...

Hi,

I would like tu use a high sensitivity USB Wifi card on my wl500g. Something what I could connect directly to the antenna with no (or very shot) cable in order to eliminate signal loss and...

Hi,

Could somebody upload an older version? For example rtorrent 0.8.4-2. The new one doesn't seem to work for me either :(
Before when I checked what is running, I saw rtorrent running as...

Hi,

Waoh...Fast answer...

I've seen this site, but it is a tutorial for custom firmware and not a tutorial for installing software from source for the existing firmware...
Or you meant, that...

Hi everyone,

I tried already native compilation, but I didn't succed, so I gave cross compiling a try. I've booted my laptop with ubuntu intrepid and I followed Jean-Fabrice's tutorial, but it...

Hi wpte!

Actually the readme only instructs to run the make and install commands, so there in no word about configuring anything. Autoconf says that it requires an input file, which obviously is...

Although I haven't got airodump-ng compiled, but I found something what actually partially gives me what I wanted. The name of this utility is airfinder. It refreshes the signal power info in every...

Well...I just found out, that it doesn't work, because the aircrack-ng tarball doesn't contain "configure" file. Anyway, I kept searching and I found a solution for openwrt (running on a fonera)....

Hi,

I followed wpte's tutorial, but I get this error right after installing optware-devel and buildroot:


-sh: ./configure: not found

What am I missing?

BTW... I'm trying to compile...

I got it working. The Putty menu was the bastard who was fooling me. Or I was the fool, I should say :o.

For others, who might do the same mistake: If you set up the tunnel and then you go back to...

Hi wpte!

Thanks for your instant reply! I knew this "trick" from before, but actually it never worked for me. Can you tell me which line(s) I should fill in the firefox proxy setup window? http,...

Hi everybody,

I was trying to follow several tutorials online about how to get around corporate proxies. My company for example is using websense to block private web access. I have squid and...

Hi,

I found out what the problem was. The permissions were not set correctly, since the user "nobody" has to be able to write in the cache directory and not only "root". Classic mistake from my...

Hi wpte,

I set up squid, but there is a strange thing going on around this one too. I successfully set it up, It starts with no error message....But approx. 5 sec after the start it disappears...

Hi,

Thanks for your tip. I turned ipv6 on, but unfortunately it didn't help. I read that squid requires a bit more decent hardware to run smoothly, meaning that on an asus wl500gP it is a bit...

Hi,

I'm trying to setup a simple proxy server by using Srelay. For some reason it doesn't start. I get the following error message:



I use this config file:

Hi,

I'm using kismet to scan wifi networks and it works fine for AP detection, but unfortunately it doesn't give me signal strength info. Kismet has the option (I think with "L" it pops up), but...

Hi,

This is exactly what I was looking for! Thanks a lot!

For the ones who are seeking for a similar solution, heres a little help from openwrt:
...

Hi there,

I'm also trying to get a solution to have a Real Time Clock on my WL500g, which does not have the required hardware unfortunately. However, I have a Dreambox (linux based satellite...