Please try to get MAX3232.
This chip is well designed for 3,3V logic level.
Please keep this in mind. Do not use MAX232!!!!
And yes, please use the 3,3V port pin from asus connector to power the...
Type: Posts; User: Randale91
Please try to get MAX3232.
This chip is well designed for 3,3V logic level.
Please keep this in mind. Do not use MAX232!!!!
And yes, please use the 3,3V port pin from asus connector to power the...
Ok, dann habe ich auch jetzt keinen Tip mehr ohne logfiles.
Das einzigste was ich mal noch hatte, war das ein CAT5-Kabel mit Modem und PC funktionierte aber mit ASUS nicht...
Hast Du noch ein...
Du hast schon noch ein DSL-Modem an der WAN-Buchse vom Asus oder ?
Wenn nicht -> dann kann das nicht gehen.
Ok, last answer:
If you always have your USB-HDD connected to your asus device all the following steps are ok for you....
So if you answer this question with NO i do not have an solution for...
ok you want to use FAT32,
but why dont you use ext2 Linux Filesystem ?
You can have 4GB files and bigger.......
Yeah you can do that with your laptop. You will see
the data with your os (XP) as network shared folder....
If you attach the drive to the asus device it
does not matter what partition type you...
For security reasons and power reasons a mail server do not have to run on a router !!!!!
(or a virus scanning engine!!!!!!)
Please google for some explanation ......
These ASUS devices are...
If you are sure that other clients could connect to the router with WPA e.g. enabled,
please check the driver verion of your wlan nic. Go and grab the latest
available drivers from vendor.
Maybe...
So whats your question ?
The log says: Out of Memory !!!!
How much ram does this daemon or program need ?
Maybe you can configure it in the config files of the program ?
Please try OLegs FW. Yes, you will see the webpages as for the original ASUS FW but with a lot of extended features.
If you use dhcp on wan port and dhcp for the normal lan1-4 ports you dont have...
Try another time server, if the received time stamp is not valid, it will not be set. Try using a local server of your country.
This could be a problem with temporarily problems
of time-server.
Thanks a lot. Will you provide the sources also ?
Maybe we can share some knowledge about thread programming...
I like your tool and have some idea to add some enhanced features.
What do think...
What program language did you use ?
Best regards
please remember: thats not normal to loose any configuration options.
All setttings are stored in flash.
There is something wrong if it will happen !!!!
If you are satisfied with the boottime...
This is pretty simple:
1. connect you ASUS WAN-Port with your normal router.
2. configure your ASUS ipadress range to another subnet
e.g. 192.168.10.xxx !!! This is really important !!!
-...
This is a general architecture USB feature (sometimes might be a problem) and
this is normal behaviour. All USB devices will enumerate.
Your problem could be resolved by adding a small USB-Hub....
Yeah, thats great.
Can you please post your working ;) .config ?
HI,
do you use "make menuconfig" ?
If not, create a backup and try to configure it with "make menuconfig"!!!!
Three month ago I had some errors with fat filesystems, too.
(missing options in...
Security Problem
Please be sure to protect your ssh access from internet or wan port !
See changelog:
http://matt.ucc.asn.au/dropbear/CHANGES
Rtfm ;-)
Hold Reset Button !
If you are a experienced guy (electronics) and want to try it yourself
(no guarantees) -> look here for the first post:
http://wl500g.info/showthread.php?t=3220&highlight=pmon
Good luck.
I have not checked the problem itself. I took my second router and flashed
it with RC4. No problems so far.
I send the bricked one to asus support and got a new one.
Sorry, but i do not know if...
What version have you used ? Was it Openwrt RC3 ?
Ask for support where you found your firmware.
Yes, then you have a problem.
Maybe a little hint:
1. Power off ASUS router
(i had the same problem, min 30minutes off!! go for a walk, take a deep breath ;) )
2. Press reset button
3....