Search:

Type: Posts; User: vladut

Search: Search took 0.01 seconds.

  1. back to english :) I have wl-hdd with the...

    back to english :)

    I have wl-hdd with the latest firmware (1.9.2.7-9).
    When I plug the k8055 board I get:
    hub.c: new USB device 00:04.0-1, assigned address 2
    usb.c: USB device not accepting new...
  2. Replies
    8
    Views
    13,814

    oleg firmware is not compatible with wl-330ge!

    oleg firmware is not compatible with wl-330ge!
  3. Replies
    8
    Views
    13,814

    It seems that version 2011 is all-in-one. I have...

    It seems that version 2011 is all-in-one.
    I have the toolchain from the original drivers CD but that is for version 2009.
    Or it can be the same toolchain.
  4. Replies
    8
    Views
    13,814

    New ASUS WL-330gE

    What about custom firmware support for this device?
    It has an bcm5354kfbg processor and the cd came with the gpl sources (toolchain.tgz + WL330gE2009_GPL.tgz).
    Can anyone (oleg :) ) integrate it...
  5. Thread: NFS / adduser

    by vladut
    Replies
    3
    Views
    6,018

    Try this:...

    Try this:
    http://www.sprayfly.com/wiki/User_Management_Guides
  6. Replies
    7
    Views
    8,961

    I have discovered one thing: For nfs mounting to...

    I have discovered one thing:
    For nfs mounting to work, portmap must be started on the NFS client.
    If you don't start it (or if you can not start it because it is not there - like in dreambox dm500)...
  7. Replies
    7
    Views
    8,961

    Same problem here. I have wl-hdd and I was...

    Same problem here.

    I have wl-hdd and I was installed stuff on it (flash with wl500g-clear-nvram.trx then with WLHDD-1.9.2.7-7g.trx) at work (net 192.168.0.0/24).
    I did not have a chance to test...
  8. Replies
    1
    Views
    18,143

    port forwarding how-to?

    I want to forward the port 8080 from wan to lan at one ip address but another port
    (194.x.x.x:8080 -> 192.168.0.10:80).
    How it can be done from admin interface?
    I think that is possible from the...
  9. Replies
    14
    Views
    6,703

    mke2fs is the command for formating (mkswap the...

    mke2fs is the command for formating (mkswap the for swapfile)
  10. Replies
    14
    Views
    6,703

    Use -j switch when formating: mke2fs -j...

    Use -j switch when formating:
    mke2fs -j /dev/ide/host0/bus0/target0/lun0/part2
  11. Replies
    14
    Views
    6,703

    It may work if you use "-t ext3" switch: mount...

    It may work if you use "-t ext3" switch:
    mount -t ext3 /dev/scsi/host0/bus0/target0/lun0/part2 /opt
  12. Replies
    14
    Views
    6,703

    It seems that you are trying to mount the swap...

    It seems that you are trying to mount the swap partition.
    TRY:
    [admin@banana /]$ mount /dev/ide/host0/bus0/target0/lun0/part2 /opt
Results 1 to 12 of 12