Search:

Sorry about no respons,
but the router is at my sisters place and she feels like not beeing able to do the changes in router.
But she is also a bit wondering if it will solve the problem cause the...

As I wrote in first post:



So, do you have an instruction for this or your cronjob (as I'm not that good with Linux)?
If it really works and make all disconnects disappear.

That is for different full implementations of Linux.
The routers just have a special limited version, so it is not possible to work.

When doing that, router say modem is connected, but I don't have any IP-adresses or access to internet.

Router/modem just going "in cirkels" and switching between the two (modem) connections with...

WL-500gP, Huawei e180 (using a USB-hub) and WL500gp-1.9.2.7-10-USB-1.71.trx.

Modem disconnecting now and then ( but modem light saying it's OK ). Then need to do a manuell disconnect and connect...

I have 1.9.2.7-7f-pre8 installed.
Isn't that one good enough / updated ?

Same question !
With a router marked/from 67 I also have this reading on "wl noise".
noise is 0 (off)

Anyone ?

Good - bad - don't worry - don't bother ?

Follow this:
http://wl500g.info/showthread.php?t=6638

Duncan
It is possible since I'm using a similar setup. You're not depending on WDS in both routers or any special things.
Your ASUS should just act as a wireless "adapter" or Station to the...

Is Client mode now working ?

last I tried with release 1.9.2.7-7f-pre4 and client mode it just acted as .... and no possibilities to contact the bricked router. => Pin 9 .....

Should I dare...

Installed Oleg´s firmware 1.9.2.7-7f-pre4.
All settings exactly as my wl-500g with 1.9.2.7-7b set up for station mode.
In Status & Logs it looks exactly the same.
BUT i can only access wl-500gP...

Message moved to Firmware discussion

How could I set the wl-500g P in Client Mode ?
In wl-500g it was possible but I haven't seen any way of doing it with
wl-500g P.

Followed Your advice. But starting with System set up and AP mode did result in a limitation of what to change, for example WAN IP-addresses.
So I started with Factory default. Changed to AP-mode...

Yes Styno, I think that is too simple. Shouldn't be, but ....
That was my 1st, 10th, 20th, 50th, 100th and ...th attempt

From Ripe and WhoIs is a confirmation about IP-address (and right owner...

Just a new comment about routing table:
I tested with some different setting for static route + Apply and not.
Now the line with ...... 128 is gone, but I now have
82.0.0.0 0.0.0.0 255.0.0.0 ...

Hopefully I've missed something

No DHCP server on switch/AP. And no other limitations except WEP.
Yes, ... 185 is free. No other is using it ( I have administration rights to W WAN and switch)...

Your thoughts are about the same as mine when I started.
Now I don't know

Bridge: I set "WDS only" in bridge settings. Open ports?
Well, when making a port scanning the only port reply I get is...

This is my wanted setup.

So, how should this be accomplished ?

Simple set up but strange effects when configuring.

As described I want my wl-500g to be wireless connected to an AP (Symbol) in a big (wireless) WAN = No modem. In the WAN we all have fixed...

Well
The commercials about wl-500g was talking about a great HW.
But it looks like it was a bit overrated.
More just a toy for connecting to other ASUS stuff. Not according to open standard,...

Same problem with connecting as Lord Mobius but in my case, “X” is an AP in a big W WAN (Symbol tech.) so I can’t fix it with firmware. I have installed 1.8.1.9 on Y.

Setting up my WL-500g (Y) as:...