Firmware v1.9.2.7 CR6, updated to CR6a ... now CR6b [Oleg]

(Where) can we read more about it Oleg?

Quote:

---

Originally Posted by FauDrei

(Where) can we read more about it Oleg?

---

In the sources. :) The problem was that you got "no such device" in the log during the printing attempt, while the printer is detected and displayed on the status page.

Quote:

---

Originally Posted by Oleg

int, it should work fine, as it mostly just a rebranded 6a.3, with except of printer fix :)

---

It seems that 6b work's very well.. :)

I will test samba and printer tomorrow..

Its not possivel to include in AP Mode: Client mode ?


This are the best thing, in wl that are missing...


Lot of work???

Quote:

---

Originally Posted by int

Its not possivel to include in AP Mode: Client mode ?


This are the best thing, in wl that are missing...


Lot of work???

---

It's already there: Wireless | Advanced | Extended mode > Ethernet Bridge.

Im now using 6b, and it seems quite stable... the auto negotiation in "wan connection speed" its working good (back again, finnally :P ).

I will continue to test after 72h of working and post my conclusions.

After some use of the 6a.3 ( ~72hours ) the firmware it seems stable and no resets, reboots or problems from services.

Once again just to remember my test's are using the WL500g with 1 connection in LAN and 3 WLAN connection WPA-PSK/ AES+TKIP ( 2 AES broadcom chip 802.11g and one 1 TKIP intel 802.11b ), with FTP server, DYNDNS and a print service port 9101.

Quote:

---

Originally Posted by Oleg

catdog: try fix speed set to auto

---

Thank you Oleg for this fix, works fine now with the auto negotiation enabled.
You are a star!

My WL500g its been runing with a quite good stability more than 72H On and going up!
Thanks for developing this firmware since the begining :)

Hi Oleg!

I use the new v1.9.2.7 CR6b firmware a few days. It's very stable, no restart, no slow down on auto negotiation mode, but the connection time is invalid in the future too.
"Jul 3 17:10:46 pppd[76]: Connect time 18673390.5 minutes."

Zitev

Hi

I can't make samba works on my WL500g... :o

I see other threats but its diferent on this FW...

I put my harddisk on WL, and i can see the files on /tmp/harddisk/


but what i have to do to make samba works fine with public read/write acess?

Quote:

---

Originally Posted by Zitev

Hi Oleg!

I use the new v1.9.2.7 CR6b firmware a few days. It's very stable, no restart, no slow down on auto negotiation mode, but the connection time is invalid in the future too.
"Jul 3 17:10:46 pppd[76]: Connect time 18673390.5 minutes."

Zitev

---

Hm... Have you read my answer?
http://wl500g.info/showpost.php?p=17766&postcount=63

Quote:

---

Originally Posted by int

Hi

I can't make samba works on my WL500g... :o

I see other threats but its diferent on this FW...

I put my harddisk on WL, and i can see the files on /tmp/harddisk/


but what i have to do to make samba works fine with public read/write acess?

---

Have you assigned LAN Hostname to your router and enabled samba? Yes, samba is changed in the 1.9.2.7-6, but it's still works fine. :) For r/w access use share$

Quote:

---

Originally Posted by Oleg

Have you assigned LAN Hostname to your router and enabled samba? Yes, samba is changed in the 1.9.2.7-6, but it's still works fine. :) For r/w access use share$

---

i already enable samba, and put LAN as my hostname, and don't work i see that smb.conf was not create...???

[QUOTE=Oleg]Hm... Have you read my answer?

Ohhh...I missed your answer, sorry...THX!

Zitev

After changing from 1.9.2.7-6.3 to 1.9.2.7.6b after a few days without any problems, I am having disconnections again. Are there any differences between those 2 firmwares?
Please take a look at my logfile.

THX