Huawei E3121(320s)/E3131(420s/d)/E303(Hi-Link) îò ÌÒÑ/Áèëàéí è ðîóòåð Asus

Quote:

---

Originally Posted by karavan

Ëîã ïîäðîáíî èçó÷àë, íî íè÷åãî ïîäîáíîãî íå âèäåë.
Ê ñòàòè, äî êîìàíäû 'insmod usbserial vendor=0x12d1 product=0x1506' ïðîáîâàë 'modprobe usbserial vendor=0x12d1 product=0x1506',

---

À ïî÷åìó âû ðåøèëè, ÷òî ó íåãî product=0x1506? Íàñêîëüêî ÿ çíàþ, ó ýòîãî ìîäåìà íå îäíà ìîäèôèêàöèÿ è íå íà îäíîì ÷èïå . Ïðîâåðüòå â Äèñïåò÷åðå óñòðîéñòâ.

Quote:

---

E3131-s2 HSPA 21.0/5.76 12d1:14fe 12d1:1506 4 0 5 & 6 serial & qmi
E3131-s H2 HSPA 21.0/5.76 12d1:151a 12d1:151d 3 0 4 & 5 2 serial & ncm & mbim

---

Èñòî÷íèê: http://www.dd-wrt.com/wiki/index.php...Working_Modems

Âîîáùå-òî, âñå ìîäóëè â ïðîøèâêå åñòü, è èçâðàùàòüñÿ ñ ïåðåñáîðêîé ïðîøèâêè, ðó÷íîé çàãðóçêîé ìîäóëåé ñ ôëåøêè è ò.ï. íå íóæíî. Âû ïîäîøëè ê ïðîáëåìå íå ñ òîé ñòîðîíû.

Äëÿ ðó÷íîé çàãðóçêè äîñòàòî÷íî óêàçàòü VID è PID â âåá-èíòåðôåéñå. À åùå ëó÷øå - ðàçîáðàòüñÿ, ïî÷åìó ìîäåì íå ïîäõâàòûâàåòñÿ àâòîìàòè÷åñêè.

Äëÿ ýòîãî íóæíî:

1. Ïîïðîáîâàòü ïðîøèâêó r5006 èëè áîëåå íîâóþ (ÿ îáíîâëÿë ñïèñîê èçâåñòíûõ ìîäåìîâ, âçÿâ åãî èç ñâåæåãî ÿäðà 3.8.6).
2. Åñëè íå çàðàáîòàåò - âûëîæèòü äèàãíîñòè÷åñêóþ èíôîðìàöèþ.

Quote:

---

Originally Posted by karavan

Ëîã ïîäðîáíî èçó÷àë, íî íè÷åãî ïîäîáíîãî íå âèäåë.

---

Íó ÷òîáû ýòî óâèäåòü, íóæíî áóäåò îáíîâèòü ïðîøèâêó íà -r5025 è íàñòðîèòü ðåæèì "Ethernet over USB" :rolleyes:

Code:

---

DHCP WAN Client: bound ('usb0'), IP: 192.168.1.100, GW: 192.168.1.1, lease time: 86400

---

Äà, è åù¸ èç-çà âîò ýòîãî - ëó÷øå ïåðåíåñòè äèàïàçîí àäðåñîâ LAN ðîóòåðà â 172.16.1.1/24 èëè 10.0.1.1/24 ;)

Quote:

---

Originally Posted by Omega

Äà, è åù¸ èç-çà âîò ýòîãî - ëó÷øå ïåðåíåñòè äèàïàçîí àäðåñîâ LAN ðîóòåðà â 172.16.1.1/24 èëè 10.0.1.1/24 ;)

---

Íàñ÷åò ïîñëåäíåãî - íå ëó÷øå. Èìåííî ýòîò äèàïàçîí èñïîëüçóþò ïî óìîë÷àíèþ YOTA'âñêèå HiLink ìîäåìû èç ëèíåéêè Yota One:

Code:

---

WAN_IP_ADDR 10.0.0.10 WAN_SUBNET_MASK 255.255.255.0 \
            WAN_DEFAULT_GATEWAY 10.0.0.1 \

---

Âäðóã ïðèäåòñÿ òàêîé ìîäåì ïîäêëþ÷èòü? ;) Íî, ïîìåíÿòü íàäî.

Íàïðèìåð ìîäåì Huawei E303 HiLink èñïîëüçóåò àäðåñ 192.168.1.1 . http://s017.radikal.ru/i425/1304/80/8765247ca5e5t.jpg


Íàäî ïðîâåðèòü ÷òî E3131 âûäàåò íà ÁÁ è íàçíà÷èòü îòëè÷íûé îò ýòîãî äèàïàçîí

Quote:

---

Originally Posted by Rusink

Íàñ÷åò ïîñëåäíåãî - íå ëó÷øå. Èìåííî ýòîò äèàïàçîí èñïîëüçóþò ïî óìîë÷àíèþ YOTA'âñêèå HiLink ìîäåìû èç ëèíåéêè Yota One:

Code:

---

WAN_IP_ADDR 10.0.0.10 WAN_SUBNET_MASK 255.255.255.0 \
            WAN_DEFAULT_GATEWAY 10.0.0.1 \

---

Âäðóã ïðèäåòñÿ òàêîé ìîäåì ïîäêëþ÷èòü? ;)

---

×èòàåì ïîñò âíèìàòåëüíåé - èìåííî 10.0.1.1/24, à íå 10.0.0.1/24 :D

Ç.Û. Ìîæíî åù¸ èñïîëüçîâàòü è Autoconfiguration Zero - 169.254.1.1/24 :cool:

Quote:

---

Originally Posted by Omega

×èòàåì ïîñò âíèìàòåëüíåé - èìåííî 10.0.1.1/24, à íå 10.0.0.1/24 :D

Ç.Û. Ìîæíî åù¸ èñïîëüçîâàòü è Autoconfiguration Zero - 169.254.1.1/24 :cool:

---

Àãà. Íå îáðàòèë âíèìàíèÿ. Ìíîãî åäèíè÷åê è íîëèêîâ, íîëèêîâ è åäèíè÷åê.:)

Ê ñîæàëåíèþ (à òî÷íåå ê ñ÷àñòüþ), óñòðîéñòâî â ýòè âûõè âêëþ÷àåòñÿ â ðàáîòó íà âñå ëåòî, à âðåìåíè íà ýêñïåðèìåíòû íåò ñîâñåì.
Íî ÷åðåç ìåñÿö-ïîëòîðà ê ýòîìó óñòðîéñòâó áóäó ïîêóïàòü "äðóçåé" äëÿ óâåëè÷. îáùåé ïðîïóñêíîé ñïîñîáíîñòè Wi-Fi íà àýðîäðîìå è ïðèëåãàþùåé òåððèòîðèè. Òîãäà è âåðíóñü ê ýòîìó âîïðîñó.
Âñåì ñïñ!  ëþáîì ñëó÷àå, Âàøè ïðîøèâêè ñàìûå íàðîäíûå!

Quote:

---

Originally Posted by Rusink

Íàäî ïðîâåðèòü ÷òî E3131 âûäàåò íà ÁÁ è íàçíà÷èòü îòëè÷íûé îò ýòîãî äèàïàçîí
Íàïðèìåð ìîäåì Huawei E303 HiLink èñïîëüçóåò àäðåñ 192.168.1.1

---

AT-êîìàíäû äëÿ ìîäåìà Huawei E3131

• AT^SETPORT="A1,A2;2,16" - (ðåæèì "ñåòåâàÿ êàðòà")
• AT^SETPORT="A1,A2;1,3,2" - (ðåæèì "òîëüêî ìîäåì")
• AT^SETPORT="A1,A2;1,3,2,A2" - (ðåæèì "ìîäåì + Card Reader")
• AT^SETPORT="A1,A2;1,16,3,2" - (ðåæèì "ìîäåì + ñåòåâàÿ êàðòà")
• AT^SETPORT="A1,A2;2,16,A1" - (ðåæèìå "ñåòåâàÿ êàðòà + CD-ROM")
• AT^SETPORT="A1,A2;1,2,3,16,A1,A2" - (ðåæèì äëÿ ðàáîòû ìîäåìà ñ Android 4.0)
• AT^SETPORT="A1,A2;1,16,3,2,A1,A2" - (óñòàíîâèòü êîíôèãóðàöèþ ïî óìîë÷àíèþ)

http://3ginfo.ru/page53.html :rolleyes:

AT-êîìàíäû äëÿ ìîäåìà Huawei E303 Hi-Link

• AT^U2DIAG=374 - ïåðåâîä ìîäåìà èç ðåæèìà Hi-Link â ðåæèì COM ïîðòîâ
• AT^U2DIAG=375 - âîçâðàò â èñõîäíûé ðåæèì Hi-Link

Code:

---

AT^GETPORTMODE?

^GETPORTMODE: TYPE: WCDMA: Huawei,MDM:0,DIAG:1,PCUI:2

---

http://cs3-3.4pda.to/1993186.png

PHP Code:

---

0 - HUAWEI Mobile Connect - 3G Modem
1 - HUAWEI Mobile Connect - 3G Application Interface
2 - HUAWEI Mobile Connect - 3G PC UI Interface 


---

My Huawei Terminal - http://alexander.give-smile.ru/terminal/

Code:

---

usb_modeswitch -v 12d1 -p 1f01 -V 012d1 -P 014db -M "55534243123456780000000000000a11062000000000000100000000000000" -W

---

http://192.168.1.1/html/switchProjectMode.html - ïåðåâîä â "ðåæèì ïðîãðàììèðîâàíèÿ"
http://192.168.1.1/html/switchDebugMode.html - ïåðåâîä â "ðåæèì îòëàäêè"

PHP Code:

---

Remote NDIS based Internet Sharing Device
FC - Application Interface (comXX)
FC - PC UI Interface (comXX)
FC - Serial Port (comXX) 


---

http://192.168.1.1/html/autoconnection.html - ïåðåâîä â "ðåæèì àâòîïîäêëþ÷åíèÿ"
http://192.168.1.1/html/ussd.html
http://192.168.1.1/html/index.html

http://192.168.1.1/html/logsetting.html - Log Settings
http://192.168.1.1/html/devicecontrol.html - Restore Default Settings
http://192.168.1.1/usermanual/en-us/...concept_1.html - Hi-Link User Guide

http://4pda.ru/forum/index.php?showtopic=350418 ;)

Íà OpenWRT îáà ìîäåìà (HUAWEI E3131 è HUAWEI E303) ïîäíÿëèñü â ðåæèìå HiLink https://sat-forum.info/index.php/top...html#msg240072

Ðîóòåð, âî èçáåæàíèå êîíôëèêòîâ ñ dhcp ìîäåìà, ïåðåâåäåí íà àäðåñ 192.168.2.1, ìîäåì ñåë íà äðàéâåð cdc-ether

Íà ïðîøèâêå "ýíòóçèàñòîâ" äîëæåí çàðàáîòàòü â ðåæèìå Ethernet over USB.

Äîáðîãî âðåìåíè ñóòîê âñåì, ðåáÿòà!
Èíòåðåñóåò âîïðîñ ïî Âàøåé òåìå, óäàëîñü ëè âñ¸ òàêè ïîäðóæèòü ìîäåì 420s(å3131) è ðîóòåð? Ïðî÷èòàâ âñþ òåìó ÿ òàê è íå ïîíÿë ñìîãëè ëè ðåøèòü âîïðîñ ñ àâòî ïîäêëþ÷åíèåì ìîäåìà!? â ëèíóêñå ÿ íå ñèë¸í,íî êîå ÷òî ìîãó ñäåëàòü, ó ìåíÿ òà æå ïðîáëåìà, íå ìîãó ìîäåì ïåðåâåñòè â ðåæèì ìîäåìà! Áóäó ïðèçíàòåëåí çà ïîìîùü!

Quote:

---

Originally Posted by nik022

Äîáðîãî âðåìåíè ñóòîê âñåì, ðåáÿòà!
Èíòåðåñóåò âîïðîñ ïî Âàøåé òåìå, óäàëîñü ëè âñ¸ òàêè ïîäðóæèòü ìîäåì 420s(å3131) è ðîóòåð? Ïðî÷èòàâ âñþ òåìó ÿ òàê è íå ïîíÿë ñìîãëè ëè ðåøèòü âîïðîñ ñ àâòî ïîäêëþ÷åíèåì ìîäåìà!? â ëèíóêñå ÿ íå ñèë¸í,íî êîå ÷òî ìîãó ñäåëàòü, ó ìåíÿ òà æå ïðîáëåìà, íå ìîãó ìîäåì ïåðåâåñòè â ðåæèì ìîäåìà! Áóäó ïðèçíàòåëåí çà ïîìîùü!

---

Íàì òîæå íåïîíÿòíî, ÷òî âû äåëàëè ñî ñâîèì ìîäåìîì è ðîóòåðîì. :) Î ïåðåêëþ÷åíèè ìîäåìà â ðåæèì com - ïîðòîâ ( ìîäåì) íàïèñàíî ÷óòü íèæå. Î ïîäêëþ÷åíèè êàê HiLink - òîæå. Ìåíÿåòå àäðåñ ðîóòåðà (íàïðèìåð íà 192.168.2.1), âûáèðàåòå ðåæèì Ethernet over USB è ïîäêëþ÷àåòå.

èìåþ äàííûé ðîóòåð, õî÷ó íà äà÷êó ñäåëàòü èíåò... ïðîáåæàëñÿ ïî ìàãàçàì åâðîñåòè è áèëàéíà.
ìîäåìû ùàñ íà âåòðèíàõ ZTE MF 667 è Huawei E3131. (â îñíîâíîì 3131)
ïîäðóæàòüñÿ ëè îíè ñ ðîóòåðîì ñ ñâåæåé ïðîøèâêîé? èëè íóíà èñêàòü ZTE 190, 192?

Quote:

---

Huawei E3131 – Disabling HiLink and turning into a dialup modem

For a while been searching for the holy grail of disabling HiLink and reverting my new
Huawei E3131 dongles back to the dialup modem based operation of previous dongles.
First step is to enable the serial console. To do this plug in your dongle and visit the following webpage

Code:

---

http://192.168.1.1/html/switchProjectMode.html

---

The modem will now restart and present a couple of serial interfaces instead.
Connect to the fist of the two interfaces, eg /dev/ttyUSB0 with a Baud rate of 9600bps using a terminal client of your choice.
I used minicom, which is available in most distros repos. And type the modem the following command.

Code:

---

AT^U2DIAG=0

---

If this is succesful it will respond with OK.
This will cause the device to permamently function in modem mode when plugged in.
To restore its HiLink functionality. Do the same and send the following command instead.

Code:

---

AT^U2DIAG=119

---

Once the device has had its mode changed in this way.
It requires removing and plugging back in to take effect.
Operating in modem mode it will change its product ID and should look like this (lsusb)

Code:

---

Bus 001 Device 082: ID 12d1:1c05 Huawei Technologies Co., Ltd. E173s 3G broadband stick (modem on)

---

If you don’t have the virtual tty’s created upon device insertion.
Then manually bind it too the option module like follows (As root obviously)

Code:

---

echo “12d1 1c05″ > /sys/bus/usb-serial/drivers/option1/new_id

---

From there you can dial out as accustomed using the first created virtual tty. eg, /dev/ttyUSB0

---

http://blog.phoenixhaven.net/2012/09...-dialup-modem/ :p

Quote:

---

Huawei E3231 - new model

The install id for the stick is 12d1:1f01 and you may see that in dmesg before usb_modeswitch switches it over to 12d1:14db.
Your lsusb shows a typical HiLink device in ethernet mode where it needs ethernet drivers which creates an additional eth device in your OS.

You can try and edit the /etc/usb_modeswitch.d config file for 12d1:1f01 and change the message contents to:
replug the stick and check with lsusb if it gets a different modem id this time.
If so, then paste the lsusb -v -d for 12d1:new id

With some luck it may become 12d1:1c05 with serial modem interfaces.
-------------
lsusb now gives a new modem id 0x1442

Code:

---

lsusb-v -d 12d1:1442

---

-------------
ok, can you then include 12d1:1441 as well?

Code:

---

usb_modeswitch -v 0x12d1 -p 0x1f01
-M "55534243123456780000000000000011062000000000000200000000000000"

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1441 Rev= 1.02
S: Manufacturer=HUAWEI
S: Product=HUAWEI HiLink
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA

I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none)
E: Ad=8f(I) Atr=03(Int.) MxPS= 64 Ivl=2ms

I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=(none)
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

I:* If#= 2 Alt= 0 #EPs= 2 Cls=02(comm.) Sub=02 Prot=ff Driver=(none)
E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0e(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

I:* If#= 3 Alt= 0 #EPs= 2 Cls=02(comm.) Sub=02 Prot=ff Driver=(none)
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0d(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

I:* If#= 4 Alt= 0 #EPs= 2 Cls=02(comm.) Sub=02 Prot=ff Driver=(none)
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

---

it is the same device as 12d1:14db but using another of Microsoft sniffed messages, it basically
adds 3 serial interfacesto the already present ecm interfaces and changes the PID.

Code:

---

usb_modeswitch -v 0x12d1 -p 0x1f01 -V 0x12d1 -P 0x14db
-M "55534243123456780000000000000a11062000000000000100000000000000"

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=14db Rev= 1.02
S: Manufacturer=HUAWEI
S: Product=HUAWEI HiLink
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA

I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none)
E: Ad=8f(I) Atr=03(Int.) MxPS= 64 Ivl=2ms

I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=(none)
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

---

-----------------
This is how a real 12d1:1c05 should look:

PHP Code:

---

SUBSYSTEMS=="usb", ATTRS{modalias}=="usb:v12D1p1C05*", KERNEL=="ttyUSB*", ATTRS{bInterfaceNumber}=="00", ATTRS{bInterfaceProtocol}=="ff", NAME="ttyUSB_utps_modem"

SUBSYSTEMS=="usb", ATTRS{modalias}=="usb:v12D1p1C05*", KERNEL=="ttyUSB*", ATTRS{bInterfaceNumber}=="01", ATTRS{bInterfaceProtocol}=="ff", NAME="ttyUSB_utps_diag"

SUBSYSTEMS=="usb", ATTRS{modalias}=="usb:v12D1p1C05*", KERNEL=="ttyUSB*", ATTRS{bInterfaceNumber}=="02", ATTRS{bInterfaceProtocol}=="ff", NAME="ttyUSB_utps_pcui" 


---

Return the stick to HiLink mode (12d1:1f01) and try the alternative modeswitch message which with a bit of luck will give the target id 12d1:1001
----------------
Yippee!

Code:

---

[ 4029.552484] option 2-4:1.0: GSM modem (1-port) converter detected
[ 4029.553620] usb 2-4: GSM modem (1-port) converter now attached to ttyUSB0
[ 4029.553748] option 2-4:1.1: GSM modem (1-port) converter detected
[ 4029.553958] usb 2-4: GSM modem (1-port) converter now attached to ttyUSB1
[ 4029.554060] option 2-4:1.2: GSM modem (1-port) converter detected
[ 4029.554938] usb 2-4: GSM modem (1-port) converter now attached to ttyUSB2

---

then using the command to return to HiLink mode

Code:

---

AT^U2DIAG=119

---

gives the following (after unplugging & replugging the dongle)

PHP Code:

---

[ 5478.288089] usb 2-4: new high-speed USB device number 5 using ehci_hcd
[ 5478.462502] Initializing USB Mass Storage driver...
[ 5478.465916] scsi6 : usb-storage 2-4:1.0
[ 5478.466181] usbcore: registered new interface driver usb-storage
[ 5478.466187] USB Mass Storage support registered.
[ 5478.601988] usb 2-4: USB disconnect, device number 5
[ 5480.384098] usb 2-4: new high-speed USB device number 6 using ehci_hcd
[ 5480.520627] cdc_ether 2-4:1.0: eth0: register 'cdc_ether' at usb-0000:00:04.1-4, CDC Ethernet Device, 58:2c:80:13:92:63
[ 5480.608841] udevd[14307]: renamed network interface eth0 to eth2 


---

It actually appears in network manager and everything!
Not tested for data access yet though, but at least it appears to be revived!

---

http://www.draisberghof.de/usb_modes...php?f=4&t=1226 ;)

Èçâåë 6 ÷àñîâ âðåìåíè, ïûòàÿñü âíèêíóòü â òÿæåëîå ðåìåñëî âëàäåëüöà ASUSîâ è íåìíîãî îäóðåë.

Èñòîðèÿ òàêàÿ. Êóïèë ñâèñòîê ÌÒÑ Êîííåêò. Âíóòðè íàïèñàíî Huawei 420D. È êóïèë RT-N66U. Âíóòðè íàïèñàíî RT-N66U (ïåðåïðîøèë íà áåòó 3.0.0.4.354). ×åñòíî ïûòàëñÿ ïîäðóæèòü äåâàéñû ñàì, íî âèäàòü ìîçãîâ íå õâàòèëî. Åäèíñòâåííîå, ÷òî óäàëîñü ñäåëàòü - ïåðåêëþ÷èòü ñâèñòîê â ðåæèì "òîëüêî ìîäåì".  ðàçâåðíóòîì îïèñàíèè íà àíãëèöêîì â ýòîé òåìå ìíîãîå íå ïîíÿòíî.

Ïðîøó! Äàéòå ïîæàëóéñòà ÷åòêîå ðóêîâîäñòâî, ÷òî ìíå äåëàòü! Ãîòîâ íà ìíîãîå ðàäè äîñòèæåíèÿ öåëè!

Quote:

---

Originally Posted by Omega

Last edited by Omega; Ñåãîäíÿ at 15:04. Ïðè÷èíà: ïîïðîáóéòå ïîäêëþ÷èòü ìîäåì íà ïðîøèâêå òîìàòî :-) òàì áûëè äîáàâëåíû íåêîòîðûå íîâûå ìîäåëè ìîäåìîâ ;)

---

Ïîñòàâèë ïðîøèâêó TOMATO (tomato-K26USB-1.28.RT-N5x-MIPSR2-108-AIO-64K.trx). Âñå áåçðåçóëüòàòíî. Ìîäåì êàê íå ðàñïîçíàâàëñÿ, òàê è íå ðàñïîçíàåòñÿ. Âîò ëîã âêëþ÷åíèÿ:

Code:

---

May  9 18:43:59 unknown daemon.info pppd[553]: System time change detected.
May  9 18:44:01 unknown daemon.info dnsmasq-dhcp[614]: DHCPDISCOVER(br0) e8:06:88:cf:73:80
May  9 18:44:01 unknown daemon.info dnsmasq-dhcp[614]: DHCPOFFER(br0) 192.168.1.39 e8:06:88:cf:73:80
May  9 18:44:01 unknown daemon.info dnsmasq-dhcp[614]: DHCPDISCOVER(br0) e8:06:88:cf:73:80
May  9 18:44:01 unknown daemon.info dnsmasq-dhcp[614]: DHCPOFFER(br0) 192.168.1.39 e8:06:88:cf:73:80
May  9 18:44:01 unknown daemon.err apcupsd[433]: apcupsd FATAL ERROR in linux-usb.c at line 609 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see <http://www.apcupsd.com/support.html>.
May  9 18:44:01 unknown daemon.err apcupsd[433]: apcupsd error shutdown completed
May  9 18:44:02 unknown daemon.info dnsmasq-dhcp[614]: DHCPREQUEST(br0) 192.168.1.39 e8:06:88:cf:73:80
May  9 18:44:02 unknown daemon.info dnsmasq-dhcp[614]: DHCPACK(br0) 192.168.1.39 e8:06:88:cf:73:80 AVs-Mac-Pro
May  9 18:44:03 unknown cron.err crond[580]: time disparity of 22801843 minutes detected
May  9 18:44:12 unknown daemon.info dnsmasq-dhcp[614]: DHCPREQUEST(br0) 192.168.1.133 cc:08:e0:15:f2:5b
May  9 18:44:12 unknown daemon.info dnsmasq-dhcp[614]: DHCPACK(br0) 192.168.1.133 cc:08:e0:15:f2:5b iPhone-Peter
May  9 18:44:18 unknown daemon.info dnsmasq-dhcp[614]: DHCPREQUEST(br0) 192.168.1.164 60:fe:c5:70:f2:79
May  9 18:44:18 unknown daemon.info dnsmasq-dhcp[614]: DHCPACK(br0) 192.168.1.164 60:fe:c5:70:f2:79 iPad-OLGA
May  9 18:44:38 unknown user.info kernel: usb 1-1.2: new high speed USB device using ehci_hcd and address 4
May  9 18:44:38 unknown user.debug hotplug[1062]: Attached USB device 1-1.2:1.0 [INTERFACE=8/6/80 PRODUCT=12d1/155b/102]
May  9 18:44:38 unknown user.debug hotplug[1066]: Attached USB device 1-1.2:1.1 [INTERFACE=8/6/80 PRODUCT=12d1/155b/102]
May  9 18:44:38 unknown user.info kernel: usb 1-1.2: configuration #1 chosen from 1 choice
May  9 18:44:38 unknown user.info kernel: scsi1 : SCSI emulation for USB Mass Storage devices
May  9 18:44:38 unknown user.info kernel: scsi2 : SCSI emulation for USB Mass Storage devices
May  9 18:44:38 unknown user.info kernel: Registered led device: 1-1.2
May  9 18:44:40 unknown user.notice kernel: scsi 1:0:0:0: CD-ROM                    Mass Storage    2.31 PQ: 0 ANSI: 2
May  9 18:44:40 unknown user.notice kernel: scsi 2:0:0:0: Direct-Access              SD Storage      2.31 PQ: 0 ANSI: 2
May  9 18:44:40 unknown user.notice kernel: sd 2:0:0:0: [sdb] Attached SCSI removable disk

---

â 18:44:38 ÿ âîòêíóë ñâèñòîê. ß òàê ïîíÿë, ÷òî îí óâèäåë òîëüêî CD è FlashCard. Ñòðàííî - ÿ îòêëþ÷èë ýòîò ðåæèì ÷åðåç HyperTerminal è íè íà PC íè íà Mac CD è FlashCard íå îïðåäåëÿþòñÿ. Íà ñòîêîâîé ïðîøèâêå ìîäåì òîæå íå îïðåäåëÿëñÿ, ò.å. îí äàæå íå óêàçûâàëñÿ â ïîäêëþ÷åííûõ óñòðîéñòâàõ.

Âîò âèä web-ìîðäû íà âêëàäêå ïðî USB.

Attachment 9549

Íà âñÿêèé ñëó÷àé. Ïîä êðûøêîé ìîäåìà íàïèñàíî HUAWEI 420D