you get no one positive detection on usb bus. The problem with usb flash drive supports my suggestion that you have hardware related problem. It looks like usb on the router isn't working at all.
Just in case, show output of:
PHP Code:
lsmod
Printable View
you get no one positive detection on usb bus. The problem with usb flash drive supports my suggestion that you have hardware related problem. It looks like usb on the router isn't working at all.
Just in case, show output of:
PHP Code:
lsmod
from the system log of the router:Code:telnet> open 192.168.1.1
Trying 192.168.1.1...
Connected to 192.168.1.1.
Escape character is '^]'.
WL-001731B42998 login: admin
Password:
[admin@WL-001731B42998 root]$ lsmod
Tainted: P
usb-storage 63080 0 (unused)
sd_mod 12660 0 (unused)
scsi_mod 72624 1 [usb-storage sd_mod]
videodev 8752 0 (unused)
audio 45160 0 (unused)
soundcore 4920 0 [audio]
printer 13060 0 (unused)
ehci-hcd 28212 0 (unused)
usb-uhci 27412 0 (unused)
usbcore 78840 1 [usb-storage audio printer ehci-hcd usb-uhci]
ip_nat_ftp 3136 0 (unused)
ip_conntrack_ftp 4584 1
wl 897336 0 (unused)
et 29088 0 (unused)
[admin@WL-001731B42998 root]$
Code:Nov 19 04:51:49 login[135]: root login on 'pts/0'
Nov 19 04:52:39 kernel: hub.c: new USB device 01:03.2-2, assigned address 16
Nov 19 04:52:40 kernel: usb.c: invalid descriptor length of 1
Nov 19 04:52:40 kernel: usb.c: unable to get device 16 configuration (error=-22)
Nov 19 04:52:40 kernel: hub.c: new USB device 01:03.2-2, assigned address 17
Nov 19 04:52:40 kernel: usb.c: too many interfaces
Nov 19 04:52:40 kernel: usb.c: unable to get device 17 configuration (error=-22)
all the needed usb modules are loaded...
Well, I don't have better guesses at the moment besides faulty usb hardware on the side of the router. Sorry.
I have tested the router with an HP Laserjet 1010. I have connected de HP 1010 with an USB cable to the router. De router recognized the HP laserjet 1010 immediately without any commands with Telnet! Then I have maked an new networkprinter under Windows XP and Ubuntu 9.10. There where on both operation systems no errors. Printing was no problem!
I have tested the internal chip from the 1010 in de 1020. The printer didn't work. Also tested the internal chip from the 1020 in the 1010 but then I get also problem's (printers doesn't work at al)Code:Nov 28 16:45:30 kernel: hub.c: new USB device 01:03.0-1, assigned address 2
Nov 28 16:45:30 kernel: printer.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0C17
Nov 28 16:45:30 kernel: printer.c: usblp0 Device ID string [143]='MFG:Hewlett-Packard;CMD:PJL,MLC,BIDI-ECP,DW-PCL;MDL:hp LaserJet 1010;CLS:PRINTER;DES:Hewlett-Packard LaserJet 1010;MEM:5MB;COMMENT:RES=600x1;'
So the only solution was to exchange the printers to "solve" this problem.
Now I have exchanged the HP Laserjet 1020 with a HP Laserjet 1010. The 1020 and 1010 are using the same toner so that maked it easy. :)
I successfully setup Kubuntu 12.10, and Windows 7 to use HP 1020 via Oleg WL500gp V2:
Kubuntu 12.10:
Driver: HP LaserJet 1020 Foomatic/foo2zjs-z1 (recommended)
Connection: lpd://192.168.1.1/LPRServer
Windows 7:
Like Windows XP, BUT don't forget to uncheck two way communication in the printer properties unless it will continuously repeat the printing job.
Hello
I am new to this site, but I want share my experience on this site. Actually, I got the problem with HP Laserjet 1020 in that The problem I am unable to print properly I asked the one technique he suggested me once re-install the driver. I did what he said. Now my printer is working very good. If you have any problem with your printer better re-install and check your printer it may work better...
HP Laserjet 1020 Printer Driver Downloading and Installation Guide
HP Laserjet 1020 printer driver download and install you must click on Free Download.
After it is downloaded on your system open the file and continue the installation process accordingly.
You can read the manual that comes with the driver software on how to use, operate and use the features of driver software.
Once it is all set up accordingly, you will be able to use your printer efficiently without any problems, as the driver will recognize all inputs and drivers to work properly in all circumstances.
Catrina Honey