New oleg firmware version

Printable View

Show 40 post(s) from this thread on one page

15-09-2009, 12:20
theMIROn

Quote:

Originally Posted by DrChair

r566 is older than r573...

yep, misread, sry

Quote:

Originally Posted by DrChair

But anyway, i tried that version aswell (downloaded from googlecode), and there I have the same problem.

As for myself, had no prob with...
Try to unplug and plug usb hdd again, and check syslog after
M.b smth wrong with your pre/post-mount script
15-09-2009, 14:47
maurer

reboot to default

i bought a SH wl-500gx and i put your latest version on the device - all the process is ok
when i tried to login i keep getting erorr on u:admin p: admin.
When i reboot the device from the button it doesn't responds anymore - only the power and the lan1 (plugged in lan) leds are on - air led is off.
I cannot telnet.
Also no response in the http.
15-09-2009, 15:11
lly

Quote:

Originally Posted by maurer

i bought a SH wl-500gx

Real wl-500gx (wl-500g deluxe) has been discontinued years ago. You are victim of ASUS marketing office, see Issue 18
15-09-2009, 16:08
maurer

i've said " i bought a SH wl-500gx"
SH as in second - hand :)

the issue remains - i cannot login
15-09-2009, 16:12
theMIROn

Quote:

Originally Posted by maurer

i've said " i bought a SH wl-500gx"
SH as in second - hand :)

the issue remains - i cannot login

turn touter into firmware restoration mode (power on with reset button pressed util powerl led will flash), then use tftp.exe to put firmware again
16-09-2009, 16:04
al37919

also make sure that your router is not wl-500gX, but wl-500 deluxe, because wl-500gx firmware is intended for deluxe.
16-09-2009, 20:43
DrChair

Quote:

Originally Posted by theMIROn

Try to unplug and plug usb hdd again, and check syslog after
M.b smth wrong with your pre/post-mount script

unplug and plug usb hdd again doesn't make any difference...

I flashed r550, and that version does find my harddisks again
(only with one of the 3, it now finds that the usb cable is bad, so I disconnected that one)

Reflashing the newest and the hdd's don't work anymore :(
16-09-2009, 20:59
lly

Quote:

Originally Posted by DrChair

unplug and plug usb hdd again doesn't make any difference...

I flashed r550, and that version does find my harddisks again
(only with one of the 3, it now finds that the usb cable is bad, so I disconnected that one)

Reflashing the newest and the hdd's don't work anymore :(

Very strange, since there was no changes from r473 to current r587 in USB subsystem at all. Seems to be, something goes wrong on your build environment or with router HW (power supply, for example).
Anyway, can you find your HDD's in

Code:

cat /proc/bus/usb/devices

output?
17-09-2009, 22:58
cichy

After upgrading to version wl500g-1.9.2.7-d-r566 of Oleg's Firmware my forum (mybb) is loading awfully long comparing to earlier version. Also in log i found this

Code:

15:46:37 dropbear[385]: exit after auth (admin): error reading: Connection reset by peer Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/1) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/1) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/1) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/1) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/1) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/1) Sep 16 16:07:23 kernel: __alloc_pages: 0-order allocation failed (gfp=0x20/0)

Dunno what may cause this :(

P.S. After upgrading to wl500g-1.9.2.7-d-r587 (2009-09-17) there are still problems with page time generation.
18-09-2009, 07:41
lly

Quote:

Originally Posted by cichy

After upgrading to version wl500g-1.9.2.7-d-r566 of Oleg's Firmware my forum (mybb) is loading awfully long comparing to earlier version.

If mybb from optware, check that you have optware's uClibc 0.9.28 in /opt/lib. If you compile it yourself (or someone else against /lib/libc.so), you have to rebuild it with newer toolchain (i.e. new uClibc).

Such messages produces kernel when physical memory is exhausted at all.
18-09-2009, 15:01
weixing

RTORRENT won't start download

I've installed the oleg firmware and rtorrent, but I find that rtorrent cannot start dl, always 0%. used ps to see and can see rtorrent is already running. Anybody knows why?
18-09-2009, 21:26
lly

Quote:

Originally Posted by DrChair

Just flashed this firmware, but now the router doesn't mount my harddisks anymore.

Hope, we fixed the bug in new r599, please try.
18-09-2009, 22:09
cichy

I've reverted to r473 and everything works fine, pages are generated better and faster then on r587. About compiling uClibc dunno exactly how to do this so i'll stick with this version.
19-09-2009, 07:23
lly

Quote:

Originally Posted by cichy

I've reverted to r473 and everything works fine, pages are generated better and faster then on r587.

Unfortunately, we can't reproduce such problem without your attention. First of all, r587 has broken USB HDD support, please try r599.

Quote:

About compiling uClibc dunno exactly how to do this so i'll stick with this version.

You don't need to compile uClibc itself, I asked against which uClibc version your application (mybb) linked. More simple question - where did you get it?
19-09-2009, 12:15
cichy

Quote:

Originally Posted by lly

Unfortunately, we can't reproduce such problem without your attention. First of all, r587 has broken USB HDD support, please try r599.

I'll try tomorrow after returning from work, maybe this will help:)

Quote:

Originally Posted by lly

You don't need to compile uClibc itself, I asked against which uClibc version your application (mybb) linked. More simple question - where did you get it?

This is what i get from ipkg list_installed cmd

Code:

uclibc-opt - 0.9.28-13 - micro C library for embedded Linux systems buildroot - 4.1.1-13 - uClibc compilation toolchain
19-09-2009, 12:18
lly

Quote:

Originally Posted by cichy

This is what i get from ipkg list_installed cmd

Code:

uclibc-opt - 0.9.28-13 - micro C library for embedded Linux systems buildroot - 4.1.1-13 - uClibc compilation toolchain

Well, but I can't see mybb. Is it from optware?
19-09-2009, 12:21
cichy

Quote:

Originally Posted by lly

Well, but I can't see mybb. Is it from optware?

Nope mybb (forum) is installed straight from the sources, from http://www.mybboard.net/ i didn't found any mybb in optware.
19-09-2009, 12:37
lly

Quote:

Originally Posted by cichy

Nope mybb (forum) is installed straight from the sources, from http://www.mybboard.net/ i didn't found any mybb in optware.

So, it is self-compiled and you have native buildroot installed. Can you provide output of

Code:

readelf -d <your_mybb_binary>

?

P.S. I never use native compiler on router since it too slow & buggy due to small RAM.
20-09-2009, 00:51
wpte

Quote:

Originally Posted by lly

So, it is self-compiled and you have native buildroot installed. Can you provide output of

Code:

readelf -d <your_mybb_binary>

?

P.S. I never use native compiler on router since it too slow & buggy due to small RAM.

it's php;)
so there can be something wrong with the php binary or extentions?
you can try to debug by executing the php files directly in the console:

Quote:

php /path/to/phpfile.php

it usually brings up a lot more information on things (or you must turn on error reporting in php.ini):)
20-09-2009, 21:20
cichy

OK gents:) After upgrading fw to verson r599 site generation time dropped to earlier values (those from r473) mybb is loading fine:) PHPSysinfo is still acting strange (long page time generation) but this is just a minor glitch that doesn't affect using forum :) Still there's an issue with updating dns for my router/site it gives

Code:

ddns update: authentication failure

and frankly i don't know what may cause this (checked password and login name they're all good)
22-09-2009, 19:04
DrChair

Quote:

Originally Posted by lly

Hope, we fixed the bug in new r599, please try.

It doesn't make any difference...
one USB-stick and one hhd on a 2.0 hub work fine, if I add a second hdd, there's trouble... I'm starting to thing the hub is broken...

cat /proc/bus/usb/devices only shows usb-hubs when the problem is there...

Also, the usb init bug was in 002-bcm5354.patch. So i don't think my WL500gP V1 was affected.
22-09-2009, 19:12
theMIROn

Quote:

Originally Posted by DrChair

It doesn't make any difference...
one USB-stick and one hhd on a 2.0 hub work fine, if I add a second hdd, there's trouble... I'm starting to thing the hub is broken...

cat /proc/bus/usb/devices only shows usb-hubs when the problem is there...

Also, the usb init bug was in 002-bcm5354.patch. So i don't think my WL500gP V1 was affected.

fix is on the way, take a patience, please
23-09-2009, 09:12
robrbarron

Post-boot script not loading

any reason why the post-boot script would not be loading on r599 ?

my usb-stick is loading as /tmp/mnt/disc0_1 , where I have used the macsat guide to configuring as /opt

if i reboot, login , umount disc0_1, then run the script, all is fine.

login as: qaz
qaz@192.168.112.51's password:
[qaz@TV_WL500 root]$ umount /tmp/mnt/disc0_1
[qaz@TV_WL500 root]$ /usr/local/sbin/post-boot
[qaz@TV_WL500 root]$ cat /tmp/var/log/post-boot
2009-09-23 17:39:52 /usr/local/sbin/post-boot started
2009-09-23 17:39:52 /dev/discs found, USB key present
2009-09-23 17:39:52 USB key partition mounted as /opt
2009-09-23 17:39:52 starting rc.unslung
2009-09-23 17:39:52 /usr/local/sbin/post-boot finished

thanks

Update.....
post-boot IS working... (not really a surprise I guess)
I trimmed it back to just logging an slowly added actions to the script.
In order to get the Usb mount command to work, I have needed to place a Sleep 10 at the top of the script, before the mount command. My USB key must be a slow one. note that post-boot starts before the NTP service collects data.

1970-01-01 10:00:06 /usr/local/sbin/post-boot started
2009-09-23 22:05:55 slept10
2009-09-23 22:05:55 /dev/discs found, USB key present
2009-09-23 22:05:55 USB Key partions mounted as /opt
2009-09-23 22:05:55 starting rc.Unslung
2009-09-23 22:05:55 finished

hope my frustration helps someone else.
28-09-2009, 13:56
weixing

samba3 and connectrek

two question for r473

1) I've put the BT dl machine into DMZ, however, I still get a lot of following message.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:35 kernel: ip_conntrack: table full, dropping packet.
Sep 28 09:30:36 kernel: ip_conntrack: table full, dropping packet.

If that's in DMZ, it should not be via NAT and thus should not have table full problem?

2) I installed samba3, everytime I restarted, I find that there are 2 instances of smbd run, which takes up 20m of memory. Is it due to 2 USB interface of WL500gP and thus need to start the daemon twice?

Reply is highly appreciated!
28-09-2009, 17:34
wpte

increase the max connections in the webinterface at the firewall pages, might work:)
05-10-2009, 18:44
!gm

Arrg got a Problem:

bought a USB - HDD Case (Wintec EX-MOB-85) for my WL500G Premium V1

Now, everytime this Device is connected it seems that the DNS resolving in my network is destroyed.
The Asus Router is working in Access Point Mode, as another Router is Gateway, with NAT, DHCP etc..
Strange that internal Adresses are reachable.

No madder if I start Router first or HDD (as its desciped by Wengi) - Problem is there.
If I disconnect the HDD or unpower it, the Routers do their Job naizly - as there never was a problem...
Firmware is: WL500gp-1.9.2.7-d-r655.trx

any suggestions?

here more:

PHP Code:

Oct 5 18:42:51 kernel: hub.c: new USB device 01:03.2-1, assigned address 3 Oct 5 18:42:52 kernel: Vendor: Maxtor 4 Model: D060H3 Rev: DAH0 Oct 5 18:42:52 kernel: Type: Direct-Access ANSI SCSI revision: 02 Oct 5 18:42:52 kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Oct 5 18:42:52 kernel: SCSI device sda: 120069936 512-byte hdwr sectors (61476 MB) Oct 5 18:42:52 kernel: /dev/scsi/host0/bus0/target0/lun0: Oct 5 18:42:52 kernel: USB device connected to the SCSI subsystem

PHP Code:

[admin@WL-002215329E61 root]$ ps PID USER VSZ STAT COMMAND 1 admin 1312 S /sbin/init 2 admin 0 SW [keventd] 3 admin 0 SWN [ksoftirqd_CPU0] 4 admin 0 SW [kswapd] 5 admin 0 SW [bdflush] 6 admin 0 SW [kupdated] 7 admin 0 SW [mtdblockd] 60 admin 1092 S dropbear 64 admin 1516 S syslogd -m 0 -O /tmp/syslog.log -S -l 7 -b 2 65 admin 1120 S httpd 66 admin 1516 S klogd 67 admin 1072 S nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan 69 admin 0 SW [khubd] 81 admin 1320 S watchdog 98 admin 0 SW [usb-storage-0] 99 admin 0 SW [scsi_eh_0] 118 admin 1152 S dropbear 119 admin 1520 S -sh 120 admin 1516 R ps

this seems normal...
I didn't created pre/post Scripts allready, because I first want to solve this problem

anyway thx to lly and Miron and all the others around here :cool:
05-10-2009, 20:04
lly

Quote:

Originally Posted by !gm

Arrg got a Problem:

bought a USB - HDD Case (Wintec EX-MOB-85) for my WL500G Premium V1

Now, everytime this Device is connected it seems that the DNS resolving in my network is destroyed.

As I can understand, DNS resolver runs on gateway router, right? And clients connected to AP? Thus, check for problem by issuing

Code:

nslookup <some_host>

on gateway, AP, client step-by-step. In case of nslookup fails on first, you should try to find problem there, not on WL500G. Otherwise, recheck what DNS servers you fill in on clients.
05-10-2009, 23:54
!gm

on the Gateway Router nslookup times out
----------------
the WL500GP does nothing, when nslookup is typed in (had to cancel it with Ctrl C)
a client behind the Asus finds the Gateway Router, but then gets a timeout, same for a client directly behind the Gateway Router

so the Problem is at the Gateway Router. But how can this be affected by an HDD that I plug into USB on the Asus? via ethernet - but why are local adresses reachable :confused: (yes i did flushdns on the clients)
14-10-2009, 08:07
Lesiuk

lly, Can you add AES-loop support into the kernel?
It would be nice for all people who want encrypt his harddisk.

http://loop-aes.sourceforge.net/loop...-v3.2h.tar.bz2
14-10-2009, 08:46
lly

Quote:

Originally Posted by Lesiuk

lly, Can you add AES-loop support into the kernel?
It would be nice for all people who want encrypt his harddisk.

http://loop-aes.sourceforge.net/loop...-v3.2h.tar.bz2

First of all, I really worry about performance of this solution on our slow CPU.

Second, this loop driver are incompatible with standart one. i.e. we have to replace standart loop driver with this one. Until I know something about it's stability & absence of artifacts, I don't want include it to mainstream. Have you additional info & web-links?

Moreover, it assume patching of util-linux package. Firmware uses util-linux from busybox, so patches provided in distributive has to be ported to apply on busybox. Not so easy task.
14-10-2009, 10:04
Lesiuk

Quote:

Originally Posted by lly

First of all, I really worry about performance of this solution on our slow CPU.

Second, this loop driver are incompatible with standart one. i.e. we have to replace standart loop driver with this one. Until I know something about it's stability & absence of artifacts, I don't want include it to mainstream. Have you additional info & web-links?

Moreover, it assume patching of util-linux package. Firmware uses util-linux from busybox, so patches provided in distributive has to be ported to apply on busybox. Not so easy task.

http://linio.terramail.pl/loopaes.html
http://translate.google.pl/translate...istory_state0=

That is howto in polish language about aes-loop, that guy tested it on P133.
So i think it should work nice on that router.

If you make special version of firmware with that enabled i can test it.
14-10-2009, 11:43
lly
Quote:

Originally Posted by Lesiuk

http://linio.terramail.pl/loopaes.html
http://translate.google.pl/translate...istory_state0=

That is howto in polish language about aes-loop, that guy tested it on P133.
So i think it should work nice on that router.

If you make special version of firmware with that enabled i can test it.

I'm not sure that such functionality will needed by much people.

kernel-2.4.37.diff can be applied to our kernel clearly, and kernel builds successfully after that. Kernel size increases +15K compressed (+60K uncompressed). So, you feel free to rebuild FW with this driver as you wish, according with readme.

procedure is simple
1. remove loop.h & loop.c from kernel as described in readme
2. patch -p1 -i kernel-2.4.37.diff at src/linux/linux
3. make oldconfig at src/linux/linux and set new parameters
4. make && make install at src/gateway
Sorry, we have much urgent tasks (related to RT-N series) and can't spend a lot of time inserting this package into FW. As I wrote in previous letter, most complex task is util-linux patching.
14-10-2009, 15:40
Lesiuk

There is AES-LOOP package in openwrt repo.

I think they are using busybox util-linux.
Can we just copy their code?

Quote:

I’m running OpenWrt “Kamkaze” on my Asus WL-500 gP (266 MHz MIPS architecture with 32 MiB RAM). Since there is no WiFi support in kernel 2.6 yet, I’m stuck to kernel 2.4. If we want to encrypt a filesystem on this setup, we need a fast and sleek encryption method running on kernel 2.4 .

http://loblog.wordpress.com/2008/05/...aze-kernel-24/

UPDATE:
Ok, now i see.
They are using util-linux-ng.
14-10-2009, 17:08
lly

Quote:

Originally Posted by Lesiuk

There is AES-LOOP package in openwrt repo.
Can we just copy their code?

No.

If it is not a top secret, for which specific task you plan to use aes-loop? Or it is just for fun?

Resonable compromiss (in case you convince me in real necessity of this module) I see in that we set loop device as module (currently it in kernel)
CONFIG_BLK_DEV_LOOP=m
and add aes-loop kernel patches to sources tree, leave they turned OFF. So, this allow to everyone to compile module without patching and use it on our public builds.
14-10-2009, 17:38
wpte

Quote:

Originally Posted by lly

First of all, I really worry about performance of this solution on our slow CPU.

I second that... if you look at a modern day machine you can do a benchmark, which gives you a decrypt speed of about 250mb/s this is straight in the ram which can go over 1500mb/s.
and that with a quad core..
so how would a slow 3,5mb/s usb harddrive with even a slower cpu perform?
14-10-2009, 18:37
Lesiuk

Quote:

Originally Posted by wpte

I second that... if you look at a modern day machine you can do a benchmark, which gives you a decrypt speed of about 250mb/s this is straight in the ram which can go over 1500mb/s.
and that with a quad core..
so how would a slow 3,5mb/s usb harddrive with even a slower cpu perform?

usb in that router can work faster than 3,5 mb/s

Code:

[root@LesiukNET www]$ hdparm -tT /dev/discs/disc0/disc /dev/discs/disc0/disc: Timing cached reads: 58 MB in 2.00 seconds = 29.00 MB/sec Timing buffered disk reads: 20 MB in 3.25 seconds = 6.15 MB/sec

29 MB/s its 230 mbit
14-10-2009, 19:19
wpte

Quote:

Originally Posted by Lesiuk

usb in that router can work faster than 3,5 mb/s

Code:

[root@LesiukNET www]$ hdparm -tT /dev/discs/disc0/disc /dev/discs/disc0/disc: Timing cached reads: 58 MB in 2.00 seconds = 29.00 MB/sec Timing buffered disk reads: 20 MB in 3.25 seconds = 6.15 MB/sec

29 MB/s its 230 mbit

true, but it's not exactly the effective speed in applications:(
the lack of enough ram is probably the most one to blame for that:p

I was talking about mb/s not mbit/s btw;)

mine goes even faster:p

PHP Code:

/dev/discs/disc0/disc: Timing cached reads: 86 MB in 2.02 seconds = 42.57 MB/sec Timing buffered disk reads: 28 MB in 3.10 seconds = 9.03 MB/sec /dev/discs/disc1/disc: Timing cached reads: 76 MB in 2.00 seconds = 38.00 MB/sec Timing buffered disk reads: 30 MB in 3.02 seconds = 9.93 MB/sec
14-10-2009, 19:23
My_Name_Is_Neo

Changelog

Hi Everyone.
I am running original Oleg's 1.9.2.7-10 firmware version on my WL-500w.
I had set it up with this firmware when i bought it back in May09. I wanted to upgrade the firmware to this new version on google code which is r665 currently. I dont have a very good reason to upgrade but I just like my gadgets to be up-to-date :P.
Now i have 2 questions -
1. Is there a changelog of what has been improved/changed over in these builds. There is no info on googlecode page and even after translation I am not able to make sense out of the Russian thread it links to.
2. I could not find a good walkthru which talks about updating the firmware. so here is my plan.
a. Restore to factory settings
b. Flash via Web-Interface
c. Re-do wengi's guide instructions again. I'll have to wipe the /opt directory. right?

Can a helpful soul point me to right direction?
Thanks
14-10-2009, 19:42
lly

Quote:

Originally Posted by My_Name_Is_Neo

1. Is there a changelog of what has been improved/changed over in these builds. There is no info on googlecode page and even after translation I am not able to make sense out of the Russian thread it links to.

Look better :p History of Changes

Quote:

2. I could not find a good walkthru which talks about updating the firmware. so here is my plan.
a. Restore to factory settings
b. Flash via Web-Interface
c. Re-do wengi's guide instructions again. I'll have to wipe the /opt directory. right?

Like all Oleg FW's - a & b - yes. You can leave /opt as is - FW don't know about it content. Probable, you have to change some scripts due to updated utils.
14-10-2009, 19:58
wpte

Quote:

Originally Posted by lly

Look better :p History of Changes

still got a question about that... the webstr module works great, but are the meta keywords also scanned?
works quite good :D

Show 40 post(s) from this thread on one page