SANE (Scanner server) - Any chance for WL-500g?

Printable View

Show 40 post(s) from this thread on one page

04-08-2007, 21:18
thira

can't start sane service

I installed sane-backends on my 500gP with Oleg firmware.
I can't start service for sane, when I try xinetd -d I've got:

Code:

07/8/5@02:40:39: DEBUG: 190 {handle_includedir} Reading included configuration file: /opt/etc/xinetd.d/saned [file=/opt/etc/xinetd.conf] [line=15] Service defaults Instances = 60 CPS = max conn:25 wait:30 Bind = All addresses. Only from: localhost(HOST) 192.168.1.0/255.255.255.0(NET) No access: No blocked sites Logging to syslog. Facility = authpriv, level = info Log_on_success flags = HOST PID Log_on_failure flags = HOST Service configuration: saned id = saned flags = IPv4 socket_type = stream Protocol (name,number) = (tcp,6) port = 6566 wait = no user = 0 group = 0 Groups = no PER_SOURCE = -1 Bind = All addresses. Server = /opt/sbin/saned Server argv = saned Only from: localhost(HOST) 192.168.1.0/255.255.255.0(NET) No access: No blocked sites Logging to syslog. Facility = authpriv, level = info Log_on_success flags = HOST PID Log_on_failure flags = HOST 07/8/5@02:40:39: ERROR: 190 {activate_normal} bind failed (Address already in use (errno = 125)). service = saned 07/8/5@02:40:39: ERROR: 190 {cnf_start_services} Service saned failed to start and is deactivated. 07/8/5@02:40:39: DEBUG: 190 {cnf_start_services} mask_max = 0, services_started = 0 07/8/5@02:40:39: CRITICAL: 190 {init_services} no services. Exiting...

and command "sane-find-scanner", I got:

Code:

[admin@ThiraBox root]$ sane-find-scanner # sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. # No SCSI scanners found. If you expected something different, make sure that # you have loaded a kernel SCSI driver for your SCSI adapter. # Also you need support for SCSI Generic (sg) in your operating system. # If using Linux, try "modprobe sg". # No USB scanners found. If you expected something different, make sure that # you have loaded a kernel driver for your USB host controller and have setup # the USB system correctly. See man sane-usb for details. # SANE has been built without libusb support. This may be a reason # for not detecting USB scanners. Read README for more details. # Not checking for parallel port scanners. # Most Scanners connected to the parallel port or other proprietary ports # can't be detected by this program. [admin@ThiraBox root]$

my scanner.o is in /opt/scanner/scanner.o
and add "insmod /opt/scanner/scanner.o" in my /usr/local/sbin/post-boot

my /opt/etc/init.d/S01sane-backends is

Code:

#!/bin/sh PATH=/sbin:/bin:/usr/bin:/usr/sbin:/opt/bin:/opt/sbin if !( grep -q ^sane-port /etc/services ); then echo "saned 6566/tcp # SANE network scanner daemon" >> /etc/services fi

Part of my Systemlog is

Code:

Aug 5 03:08:33 kernel: Adding Swap: 514040k swap-space (priority -1) Aug 5 03:08:33 kernel: usb.c: registered new driver usbscanner Aug 5 03:08:33 kernel: scanner.c: 0.4.16:USB Scanner Driver Aug 5 03:08:33 System log daemon exiting.

How can I fix this. Many thanks for help.
10-09-2007, 23:57
mistraller

Great Howto!

I followed this tutorial, and works as a charm!

HP 6300c

with Sanetwain.
No problems at all.
(I still have to create post-boot additions)

I think I will include /etc/services in /usr/local/.files before flashfs save
Looks the easiest solution to me...
27-10-2007, 12:25
mrobo

does this firmware work with asus-w500g Premium ???
need connect scanner-printer canon ir1018
i need scanning and printing too
03-01-2008, 13:04
pavelba

Epson scanner

I have Epson scanner V200. The above mentioned procedure is not applicable for it.
I suppose that I need Epson back-end. The source files are on EPKOWA web: http://www.avasys.jp/english/linux_e/dl_scan.html
I am not able to compile it (I am not expert). Can anybody able to compile it?
Please help me. Thanks.
03-01-2008, 13:58
oleo

Hm. Mail me more details on this backend.
08-01-2008, 15:57
oleo

1 Attachment(s)

The problem with the iscan source is that it heavily uses C++ for library and patches to the source is needed.

I have attached iscan.mk to start with. For more instructions how to build this visit http://trac.nslu2-linux.org/optware and wiki on www.nslu2-linux.org

When you wil have workable version you can post me to include it into optware. I am watching this thread so we can stay in touch here.
22-01-2008, 08:34
pavelba

1 Attachment(s)

Epkowa

Hi Oleo,
Whole package “iscan” is not possible to build due to missing library GDE. I am sure that this library will miss permanently.
I am working on backend “epkowa” only. I installed the following packages: buildrot, coreutils, libtool, m4 and make. I separated backend necessary files and a little bit modified. But one of source file I can not compile “libltdl/ltdl”. This library needs a C++ library “argz”.
Do you know where is possible to get this library and header for it?
When you interest it you can see my version of epkowa backend source files (not finished).
22-01-2008, 21:14
oleo

You should look for emerge builds examples or maybe some debian/ubuntu packages for dependencies. In any case I think that C++ code will need to be adapted for tollchain in use (4.1.1) and uclibc or glibc directly.
28-01-2008, 14:52
pavelba

2 Attachment(s)

sane-backends-extras

I founded on Debian server the source files <sane-backends-extras-1.0.18.16>.
I file <configure.in> I remove the following unix variants: AIX, MINIX and ISC_POSIX and set default compiler/linker include directory to </opt/include>.
Run <autoconf> and got <configure> file.
Run <configure> and got a lot of <makefile’s>.
Change <prefix> to </opt> in each of <makefile> and run <make>.
After building all files I tried to use <make install> but without success. Due to I copied all files <libsane-epkowa.*> from <backend/.libs> to </opt/lib/sane> and made symlink and copy <epkowa.conf> file to </opt/etc/sane>.

The command <scanimage –L> do not find any scanner and <sane-find-scanner> find my scanner Epson V200.

Can anybody to test my compiled backend driver for their scanner and tell me how to correct install backend driver.

Thanks.

PS. I planned to attach all files after compilation but there is some space limitation. Due to I attach the original source files and compiled drivers only. If you have some problems, send me your e-mail and I will send to you all files after compilation by e-mail.
31-01-2008, 22:39
oleo

I repeat.
First try to get It working on linux machine. Then go to cross-compile. See instructions at nslu2-linux.org site and http://trac.nslu2-linux.org/optware
01-02-2008, 12:54
pavelba

Oleo,
I found where is problem. The Sane-backends-extras package is compiled well (I hope). But some scannres:
- Perfection 1250/Perfection 1250 PHOTO
- Perfection 1260/Perfection 1260 PHOTO
- Perfection 2480 PHOTO
- Perfection 2580 PHOTO
- Perfection 3170 PHOTO
- Perfection 3490 PHOTO
- Perfection 3590 PHOTO
- Perfection 4180 PHOTO
- Perfection 4490 PHOTO
- Perfection V10
- Perfection V100 PHOTO
- Perfection V200 PHOTO
- Perfection V350 PHOTO
needs a additional plugin. This plugin is in iscan package, but it is precompiled for i386 architecture only. The Avasys company do not distribute a source files.
04-02-2008, 23:13
dotmaster

HP AIO (Officejet 5600) - libsane-hpaio?

Hi all,

I have the following problem. Attached my HP AIO USB-Scanner.
- Installed sane-backends
- and alex_g's scanner.o with my vendor settings
sane-find-scanner shows me now the device, but scanning with scanimage does not work, which means that there is no suiting SANE backend. Tried to debug and infact

Code:

$ export SANE_DEBUG_DLL=128 $ scanimage -L

gives me the debug output that no backend module in /opt/lib/sane is fitting.
[dll] sane_get_devices: found 0 devices

Going to the sane website gives me no support, as it seems that this project is not very active anymore.
However going to the HPLIP project has support for my device (via SANE), but the module libsane-hpaio seems to be needed.

HPLIP seems not to be available as an Optware Package?!:(

Can someone help me to compile this module (libsane-hpaio) out of HPLIP or to compile HPLIP???

Thx

Gregor

Quote:

Originally Posted by lohmueller

Hi all

I tried to attach an Epson USB-Scanner to my WL500gx. At first it looks good, but I'm unable to scan anything. Directly connected to my linux-notebook, this scanner works great with sane.

What I did:
- Installed sane-backends
- and alex_g's scanner.o

sane-find-scanner shows me now the device, but scanning with scanimage does not work (see output below).

Any ideas?

Thanks.

Thomas

Code:

[admin@router /tmp]$ sane-find-scanner ... found USB scanner (vendor=0x04b8, product=0x011d) at /dev/usb/scanner0 found USB scanner (vendor=0x04b8 [EPSON], product=0x011d [EPSON Scanner], chip=LM983x?) at libusb:001:002 # Your USB scanner was (probably) detected. It may or may not be supported by # SANE. Try scanimage -L and read the backend's manpage. ... [admin@router /tmp]$ scanimage -L No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages).
05-02-2008, 08:11
oleo

Give me a pointer to similar gentoo package and downloadable source code.
05-02-2008, 10:12
dotmaster

Hi oleo,

Quote:

Originally Posted by oleo

Give me a pointer to similar gentoo package and downloadable source code.

Gentoo sources I have found can be found here (current version 2.7.12)http://gentoo-portage.com/net-print/hplip
HPLIP homepage is here: http://hplip.sourceforge.net/downloads.html

Then I have found a debian port to mipsel of HPLIP at http://packages.debian.org/hplip?lang=en&keywords=hplip but the packages seam quite old to me and I don't know which kernel they were built for.

don't know if this could be useful?:confused:

please let me know if you need further info!

thank you

Gregor
06-02-2008, 00:30
oleo

I have prepared HPLIP package with changeset/7719

This is quite huge package that I assume needs expert knowledge for getting most of it. Anyway package needs testing for all platforms until it will be available at nslu2 repository. Wait until then. Then fiddle it by yourself and post me your findings when u have positive results.
06-02-2008, 11:03
dotmaster

OPTWARE PACKAGE

Thanks oleo,

that´s great news!!! :cool:
The HPLIP package is supporting 1,257 printers and scanners from HP, so I think this will help many people if we get it running.

I´m not a big expert in compiling however, but will try to check it out and cross compile it and let you know here.

Anyway thank you so much for your effort.

Kind regards, gregor
08-02-2008, 15:14
oleo

hplip can be found in repositories by now.
08-02-2008, 17:52
dotmaster

Oleo, you THA MAN faster then a light beam!:)

I will let you know my results soon! Cheers!

Quote:

Originally Posted by oleo

hplip can be found in repositories by now.
08-02-2008, 19:01
dotmaster

hplip: dlopen + File not found

Hi oleo,

I have installed Hplip; but it doesn't work yet: this is the output I get from scanimage -L

Quote:

scanimage -L
[sanei_debug] Setting debug level of dll to 128.
[dll] sane_init: SANE dll backend version 1.0.12 from sane-backends 1.0.18-cvs
[dll] sane_init: reading dll.conf
[dll] add_backend: adding backend `hpaio'
[dll] sane_get_devices
[dll] load: searching backend `hpaio' in `/opt/lib/sane'
[dll] load: trying to load `/opt/lib/sane/libsane-hpaio.so.1'
[dll] load: dlopen()ing `/opt/lib/sane/libsane-hpaio.so.1'
[dll] load: dlopen() failed (File not found)
[dll] sane_get_devices: found 0 devices

The interesting part of this problem is that the file /opt/lib/sane/libsane-hpaio.so.1 is actually where the app is looking for it.

futher reading on the error brought me to the dlopen man page: http://linux.die.net/man/3/dlopen and to this thread from a guy on a mips board without an answer ...

hp-check and hp-scan commands provided by hplip give me:

Quote:

CUPSEXT could not be loaded. Please check HPLIP installation.

This is however related to CUPS and not to SANE, but it makes me think that there is something general missing here. What do you suggest?

This is the only thing I found googling for this error:
https://answers.launchpad.net/hplip/+question/20762

Kind regards
09-02-2008, 08:22
oleo

If you are able to understand kernel system calls than I suggest that you install package strace and run scanimage with strace. Otherwise we must find a line where this ouput occured and figure out possible outcomes that generated this output.

Normally status reports from programs give us most probable cause for the error. Eg. missing filename. If filename is there then there is a problem with loading .so files.

If this is a C++ source code then most probable the problem is with libuclibc++ that has some problems with LJSJ unwind. And the simplest solution is to build the sources without uclibc++.

THis seems to be sane related problem that can be caused by differences in build parameters with sane and hplip. And it might go as far as to uclibc dynamic loader. >What you can do is to install buildroot package on your router and then try to compile simple programs with dlopen.
15-03-2008, 15:49
renegade

SANE-Backends-1.0.19

SANE-Backends-1.0.19 has been released on Februar with new and updated backends. I'm not a Linux guru, I can't build the ipk package, but I need it -- I want to buy a new scanner. Have anybody already planned to build the new version?
16-03-2008, 19:08
oleo

It was not so old. Anyway http://trac.nslu2-linux.org/optware/changeset/7986 upgraded sane-backends to latest release.
16-03-2008, 21:34
renegade

But the ipk package is pretty old...
17-03-2008, 06:51
oleo

It seems that wl500g is not supported any more. Oleg firmware now uses http://ipkg.nslu2-linux.org/feeds/op.../cross/stable/
To get this package you must use wl500g toolchain yourself.
18-03-2008, 04:42
PCTV

Help configuring a EPSON CX3650

Hi everyone,

I have been trying to follow this howto and now i am stuck on getting xinet working. i got this strange error:
Jan 1 00:00:14 xinetd[167]: Bad socket type: stream^M [file=/opt/etc/xinetd.d/saned] [line=4]

I created the file with nano editor...

Can anyone give a clue of whats the problem?

Thanks in advance,
PCTV

here goes the system log:

Code:

Jan 1 00:00:11 kernel: kjournald starting. Commit interval 5 seconds Jan 1 00:00:11 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal Jan 1 00:00:11 kernel: EXT3-fs: mounted filesystem with ordered data mode. Jan 1 00:00:11 kernel: Adding Swap: 70700k swap-space (priority -1) Jan 1 00:00:12 kernel: printer.c: usblp0 Device ID string [84/max 1552]='MFG:EPSON;CMD:ESCPL2,BDC,D4;MDL:Stylus CX3600;CLS:PRINTER;DES:EPSON Stylus CX3600;' Jan 1 00:00:12 kernel: printer.c: Parsing USBLPID... Jan 1 00:00:12 kernel: HTB init, kernel part version 3.16 Jan 1 00:00:12 kernel: HTB: quantum of class 10001 is big. Consider r2q change. Jan 1 00:00:13 kernel: HTB: quantum of class 10010 is small. Consider r2q change. Jan 1 00:00:13 kernel: HTB: quantum of class 10011 is small. Consider r2q change. Jan 1 00:00:13 kernel: HTB: quantum of class 10013 is big. Consider r2q change. Jan 1 00:00:14 kernel: HTB init, kernel part version 3.16 Jan 1 00:00:14 kernel: HTB: quantum of class 10001 is big. Consider r2q change. Jan 1 00:00:14 xinetd[167]: Bad socket type: stream^M [file=/opt/etc/xinetd.d/saned] [line=4] Jan 1 00:00:14 xinetd[167]: Error parsing attribute socket_type - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=4] Jan 1 00:00:14 xinetd[167]: Server /opt/sbin/saned^M is not executable [file=/opt/etc/xinetd.d/saned] [line=5] Jan 1 00:00:14 xinetd[167]: Error parsing attribute server - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=5] Jan 1 00:00:14 xinetd[167]: Protocol tcp^M not in /etc/protocols [file=/opt/etc/xinetd.d/saned] [line=6] Jan 1 00:00:14 xinetd[167]: Error parsing attribute protocol - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=6] Jan 1 00:00:14 xinetd[167]: Unknown user: root^M [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:14 xinetd[167]: Error parsing attribute user - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:14 xinetd[167]: Unknown group: root^M [file=/opt/etc/xinetd.d/saned] [line=8] Jan 1 00:00:14 xinetd[167]: Error parsing attribute group - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=8] Jan 1 00:00:14 xinetd[167]: Bad value for wait: no^M [file=/opt/etc/xinetd.d/saned] [line=9] Jan 1 00:00:14 xinetd[167]: Error parsing attribute wait - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=9] Jan 1 00:00:14 xinetd[167]: Bad value: no^M [file=/opt/etc/xinetd.d/saned] [line=10] Jan 1 00:00:14 xinetd[167]: Error parsing attribute disable - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=10] Jan 1 00:00:14 xinetd[167]: 167 {init_services} no services. Exiting... Jan 1 00:00:14 kernel: lp driver: get device ID Jan 1 00:00:14 xinetd[171]: Bad socket type: stream^M [file=/opt/etc/xinetd.d/saned] [line=4] Jan 1 00:00:14 xinetd[171]: Error parsing attribute socket_type - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=4] Jan 1 00:00:14 xinetd[171]: Server /opt/sbin/saned^M is not executable [file=/opt/etc/xinetd.d/saned] [line=5] Jan 1 00:00:14 xinetd[171]: Error parsing attribute server - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=5] Jan 1 00:00:14 xinetd[171]: Protocol tcp^M not in /etc/protocols [file=/opt/etc/xinetd.d/saned] [line=6] Jan 1 00:00:14 xinetd[171]: Error parsing attribute protocol - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=6] Jan 1 00:00:14 xinetd[171]: Unknown user: root^M [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:14 xinetd[171]: Error parsing attribute user - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:14 xinetd[171]: Unknown group: root^M [file=/opt/etc/xinetd.d/saned] [line=8] Jan 1 00:00:14 xinetd[171]: Error parsing attribute group - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=8] Jan 1 00:00:14 xinetd[171]: Bad value for wait: no^M [file=/opt/etc/xinetd.d/saned] [line=9] Jan 1 00:00:14 xinetd[171]: Error parsing attribute wait - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=9] Jan 1 00:00:14 xinetd[171]: Bad value: no^M [file=/opt/etc/xinetd.d/saned] [line=10] Jan 1 00:00:14 kernel: neg fail Jan 1 00:00:14 xinetd[171]: Error parsing attribute disable - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=10] Jan 1 00:00:14 xinetd[171]: 171 {init_services} no services. Exiting... Jan 1 00:00:14 kernel: neg fail Jan 1 00:00:14 kernel: HTB: quantum of class 10010 is small. Consider r2q change. Jan 1 00:00:14 kernel: HTB: quantum of class 10011 is small. Consider r2q change. Jan 1 00:00:14 kernel: HTB: quantum of class 10013 is big. Consider r2q change. Jan 1 00:00:14 kernel: HTB init, kernel part version 3.16 Jan 1 00:00:14 kernel: HTB: quantum of class 10001 is big. Consider r2q change. Jan 1 00:00:15 kernel: HTB: quantum of class 10010 is small. Consider r2q change. Jan 1 00:00:15 kernel: HTB: quantum of class 10011 is small. Consider r2q change. Jan 1 00:00:15 kernel: HTB: quantum of class 10013 is big. Consider r2q change. Jan 1 00:00:15 dhcp client: bound IP : 83.132.141.130 from 83.132.141.254 Jan 1 00:00:20 kernel: MSDOS FS: Using codepage 850 Jan 1 00:00:20 USB storage: vfat fs at /dev/discs/disc1/part1 mounted to /tmp/mnt/disc1_1 Mar 18 04:23:02 ntp client: Synchronizing time with time.nist.gov ...
18-03-2008, 07:44
oleo

Try

Code:

sed -i -e 's/\r$//' /opt/etc/xinetd.d/saned
18-03-2008, 12:10
PCTV

Thanks Oleo, for the fast response but didnt work... :(

Code:

Jan 1 00:00:11 kernel: kjournald starting. Commit interval 5 seconds Jan 1 00:00:11 dnsmasq[90]: DHCPREQUEST(br0) 192.168.1.203 00:19:d2:53:70:51 Jan 1 00:00:11 dnsmasq[90]: DHCPACK(br0) 192.168.1.203 00:19:d2:53:70:51 MARIOGON-M400 Jan 1 00:00:11 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal Jan 1 00:00:11 kernel: EXT3-fs: mounted filesystem with ordered data mode. Jan 1 00:00:11 kernel: Adding Swap: 70700k swap-space (priority -1) Jan 1 00:00:12 kernel: printer.c: usblp0 Device ID string [84/max 1552]='MFG:EPSON;CMD:ESCPL2,BDC,D4;MDL:Stylus CX3600;CLS:PRINTER;DES:EPSON Stylus CX3600;' Jan 1 00:00:12 kernel: printer.c: Parsing USBLPID... Jan 1 00:00:12 kernel: HTB init, kernel part version 3.16 Jan 1 00:00:13 kernel: HTB: quantum of class 10001 is big. Consider r2q change. Jan 1 00:00:13 kernel: HTB: quantum of class 10010 is small. Consider r2q change. Jan 1 00:00:13 kernel: HTB: quantum of class 10011 is small. Consider r2q change. Jan 1 00:00:13 kernel: HTB: quantum of class 10013 is big. Consider r2q change. Jan 1 00:00:14 kernel: HTB init, kernel part version 3.16 Jan 1 00:00:14 xinetd[171]: Bad socket type: stream^M [file=/opt/etc/xinetd.d/saned] [line=4] Jan 1 00:00:14 xinetd[171]: Error parsing attribute socket_type - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=4] Jan 1 00:00:14 xinetd[171]: Server /opt/sbin/saned^M is not executable [file=/opt/etc/xinetd.d/saned] [line=5] Jan 1 00:00:14 xinetd[166]: Bad socket type: stream^M [file=/opt/etc/xinetd.d/saned] [line=4] Jan 1 00:00:14 xinetd[166]: Error parsing attribute socket_type - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=4] Jan 1 00:00:14 xinetd[166]: Server /opt/sbin/saned^M is not executable [file=/opt/etc/xinetd.d/saned] [line=5] Jan 1 00:00:14 xinetd[166]: Error parsing attribute server - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=5] Jan 1 00:00:14 xinetd[166]: Protocol tcp^M not in /etc/protocols [file=/opt/etc/xinetd.d/saned] [line=6] Jan 1 00:00:14 xinetd[171]: Error parsing attribute server - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=5] Jan 1 00:00:14 xinetd[171]: Protocol tcp^M not in /etc/protocols [file=/opt/etc/xinetd.d/saned] [line=6] Jan 1 00:00:14 xinetd[166]: Error parsing attribute protocol - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=6] Jan 1 00:00:14 xinetd[166]: Unknown user: root^M [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:14 xinetd[166]: Error parsing attribute user - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:14 xinetd[166]: Unknown group: root^M [file=/opt/etc/xinetd.d/saned] [line=8] Jan 1 00:00:14 xinetd[166]: Error parsing attribute group - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=8] Jan 1 00:00:14 xinetd[166]: Bad value for wait: no^M [file=/opt/etc/xinetd.d/saned] [line=9] Jan 1 00:00:14 xinetd[166]: Error parsing attribute wait - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=9] Jan 1 00:00:14 xinetd[166]: Bad value: no^M [file=/opt/etc/xinetd.d/saned] [line=10] Jan 1 00:00:14 xinetd[166]: Error parsing attribute disable - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=10] Jan 1 00:00:14 xinetd[166]: 166 {init_services} no services. Exiting... Jan 1 00:00:14 kernel: lp driver: get device ID Jan 1 00:00:14 xinetd[171]: Error parsing attribute protocol - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=6] Jan 1 00:00:14 xinetd[171]: Unknown user: root^M [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:14 xinetd[171]: Error parsing attribute user - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:14 kernel: neg fail Jan 1 00:00:14 xinetd[171]: Unknown group: root^M [file=/opt/etc/xinetd.d/saned] [line=8] Jan 1 00:00:14 xinetd[171]: Error parsing attribute group - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=8] Jan 1 00:00:14 xinetd[171]: Bad value for wait: no^M [file=/opt/etc/xinetd.d/saned] [line=9] Jan 1 00:00:14 xinetd[171]: Error parsing attribute wait - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=9] Jan 1 00:00:14 xinetd[171]: Bad value: no^M [file=/opt/etc/xinetd.d/saned] [line=10] Jan 1 00:00:14 xinetd[171]: Error parsing attribute disable - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=10] Jan 1 00:00:14 xinetd[171]: 171 {init_services} no services. Exiting... Jan 1 00:00:14 kernel: neg fail
18-03-2008, 12:58
oleo

It is obvious that you have DOS CR/LD problem. Erase config and type if from scratch using vi.
18-03-2008, 14:03
PCTV

It got better after editing with VI.

Thanks again for this fantastic HowTo and support!

Now it returns the following error:

Code:

Jan 1 00:00:13 xinetd[166]: Unknown user: root [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:13 xinetd[166]: Error parsing attribute user - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:13 xinetd[166]: service/protocol combination not in /etc/services: saned/tcp Jan 1 00:00:13 xinetd[166]: 166 {init_services} no services. Exiting...
18-03-2008, 15:14
oleo

duplicate user admin in /etc/passwd to root
and register /etc/passwd in flashfs /usr/local/.files
18-03-2008, 15:34
PCTV

Sorry for my newbie questions, but what do you mean by register, i dont have the file or directory .files...

Concerning the duplicating my passwd its now like this:

admin:$$$$$$$$$$$$$$$$$/:0:0:root:/usr/local/root:/bin/sh
root:$$$$$$$$$$$$$$$$/:0:0:root:/usr/local/root:/bin/sh
nobody:x:99:99:nobody:/:/sbin/nologin

the log appears like this:

Code:

Jan 1 00:00:05 kernel: hub.c: USB hub found Jan 1 00:00:05 kernel: hub.c: 4 ports detected Jan 1 00:00:05 kernel: lp0: using parport0 (polling). Jan 1 00:00:06 kernel: hub.c: new USB device 00:04.0-1.1, assigned address 3 Jan 1 00:00:06 kernel: usb.c: USB device 3 (vend/prod 0x1370/0x2168) is not claimed by any active driver. Jan 1 00:00:06 kernel: usb.c: registered new driver usblp Jan 1 00:00:06 kernel: printer.c: v0.13: USB Printer Device Class driver Jan 1 00:00:06 kernel: hub.c: new USB device 00:04.0-1.2, assigned address 4 Jan 1 00:00:06 kernel: printer.c: usblp0: USB Bidirectional printer dev 4 if 1 alt 0 proto 2 vid 0x04B8 pid 0x080E Jan 1 00:00:06 kernel: printer.c: usblp0 Device ID string [84]='MFG:EPSON;CMD:ESCPL2,BDC,D4;MDL:Stylus CX3600;CLS:PRINTER;DES:EPSON Stylus CX3600;' ........ Jan 1 00:00:11 kernel: printer.c: usblp0 Device ID string [84/max 1552]='MFG:EPSON;CMD:ESCPL2,BDC,D4;MDL:Stylus CX3600;CLS:PRINTER;DES:EPSON Stylus CX3600;' Jan 1 00:00:11 kernel: printer.c: Parsing USBLPID... Jan 1 00:00:12 kernel: HTB init, kernel part version 3.16 Jan 1 00:00:12 kernel: HTB: quantum of class 10001 is big. Consider r2q change. Jan 1 00:00:12 kernel: HTB: quantum of class 10010 is small. Consider r2q change. Jan 1 00:00:12 kernel: HTB: quantum of class 10011 is small. Consider r2q change. Jan 1 00:00:13 kernel: usb.c: registered new driver usbscanner Jan 1 00:00:13 kernel: scanner.c: 0.4.16:USB Scanner Driver Jan 1 00:00:13 kernel: HTB: quantum of class 10013 is big. Consider r2q change. Jan 1 00:00:13 xinetd[158]: Unknown user: root [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:13 xinetd[158]: Error parsing attribute user - DISABLING SERVICE [file=/opt/etc/xinetd.d/saned] [line=7] Jan 1 00:00:13 xinetd[158]: service/protocol combination not in /etc/services: saned/tcp Jan 1 00:00:13 xinetd[158]: 158 {init_services} no services. Exiting...

And scanimage -L doesn´t found anything...

Once again, thanks,

Mário
18-03-2008, 23:55
PCTV

Hi everyone,

I figure it out the register and dupicating, and minor issues... :)

The only error on log now is:

Code:

Jan 1 00:00:03 kernel: hub.c: new USB device 00:04.0-1.2, assigned address 4 Jan 1 00:00:03 kernel: usb.c: USB device 4 (vend/prod 0x4b8/0x80e) is not claimed by any active driver. ........ Jan 1 00:00:13 kernel: usb.c: registered new driver usbscanner Jan 1 00:00:13 kernel: scanner.c: 0.4.16:USB Scanner Driver Jan 1 00:00:13 kernel: scanner.c: probe_scanner: User specified USB scanner -- Vendor:Product - 4b8:80e Jan 1 00:00:13 kernel: HTB init, kernel part version 3.16 Jan 1 00:00:13 kernel: HTB: quantum of class 10001 is big. Consider r2q change. Jan 1 00:00:13 kernel: HTB: quantum of class 10010 is small. Consider r2q change. Jan 1 00:00:13 kernel: HTB: quantum of class 10011 is small. Consider r2q change. Jan 1 00:00:13 xinetd[160]: xinetd Version 2.3.14 started with no options compiled in. Jan 1 00:00:13 xinetd[160]: Started working: 1 available service Jan 1 00:00:13 xinetd[166]: bind failed (Address already in use (errno = 125)). service = saned Jan 1 00:00:13 xinetd[166]: Service saned failed to start and is deactivated. Jan 1 00:00:13 xinetd[166]: 166 {init_services} no services. Exiting...

So far scanimage -L doesnt find any scanners...
I have a all-in-one Epson CX3650.

I guess i need the Epson backend. I founf this one http://khk.net/sane/download.html but i not able to compile it... Can anyone do it, please?

Thanks in advance, for any help...

PCTV
19-03-2008, 07:57
oleo

xinetd is neded for remote scanning only. You must edit dll.conf and inclde appropriate scanner. Like

Code:

# /etc/sane.d/dll.conf - Configuration file for the SANE dynamic backend loader # # See the end of this file for information on some specific backends. # enable the next line if you want to allow access through the network: #net epson

Then you could try scanimage of findscanner. Of course you need USB modules loaded into kernel.

Edit /etc/services and include sane service!

Yur driver should be included in sane-backends distro
19-03-2008, 08:47
PCTV

Good morning Oleo,

I have the following info on these files:
- /etc/services

Code:

# Local services saned 6566/tcp # SANE network scanner daemon

- dll.conf, epson, line is included
- /opt/etc/sane.d/epson.conf

Code:

usb # For libusb support for unknown scanners use the following command # usb <product ID> <device ID> # e.g.: usb 0x4b8 0x080e # And for the scanner module, use the following configuration: usb /dev/usbscanner0 usb /dev/usb/scanner0

What do you mean by "try scanimage of findscanner".
Regarding the USB modules they should be ok, because i can print remotely...

The output of lsmod, looks like this, and show that scanner module is loaded:

Code:

[admin@wl500g sane.d]$ lsmod Module Size Used by Tainted: P scanner 11996 0 (unused) usb-storage 63928 2 sd_mod 13276 4 scsi_mod 70200 2 [usb-storage sd_mod] printer 12836 0 lp 8668 0 parport_splink 2956 1 parport 25696 1 [lp parport_splink] usb-ohci 21908 0 (unused) usbcore 78496 1 [scanner usb-storage printer usb-ohci] ip_nat_ftp 3912 0 (unused) ip_conntrack_ftp 5216 1 wl 728968 0 (unused) et 31256 0 (unused)

What is missing? :confused:

Cheers,
Mário
19-03-2008, 12:02
oleo

man sane-find-scanner and man scanimage
19-03-2008, 12:15
PCTV

unfortenatly, either sane-find-scanner and scanimage -L found the scanner...

PcTv
19-03-2008, 12:36
oleo

I suggest, that You first try to get a running sane/xsane on some linux box. Eventualy You could also try virtualbox or some vmware-server product that is free. Try USB key to prove USB functionality. Then proceed with scanner.
19-03-2008, 13:07
PCTV

I found this HowTo and aparentely the printer and scanner should work with the sane-backend we are using on Oleg firmware...

http://gentoo-wiki.com/HOWTO_EPSON_C..._configuration

Do we have any kind o debuging or logging we can activate to determine why the scanner is not being found?

:(

PCTV
19-03-2008, 15:51
PCTV

Activated some debug flags and got the following return from scanimage -T

Code:

[dll] sane_init: SANE dll backend version 1.0.12 from sane-backends 1.0.18-cvs .... [dll] load: searching backend `epson' in `/opt/lib/sane' [dll] load: trying to load `/opt/lib/sane/libsane-epson.so.1' [dll] load: dlopen()ing `/opt/lib/sane/libsane-epson.so.1' [dll] init: initializing backend `epson' [dll] init: backend `epson' is version 1.0.247 [dll] sane_get_devices: found 0 devices

From the info on http://www.sane-project.org/sane-mfgs.html#API i believe we need a more recent backend like the one (libsane-epson.so.1.0.4) i found on this site http://khk.net/sane/news.html

How can i deploy it? Is just a copy to /opt/lib/saned ? What configuration changes should be done?

I also found this one http://khk.net/sane/download.html but i don't know how to compile it... Can anyone do it, please?

Thanks in advance,
PCTV
24-03-2008, 21:42
karlson911

I use 1.9.2.7-9 Oleg Firmware on Asus wl-500gP
My Printer-Scanner is HP LJ M1120 MFP
Printer work Excellent, but scanner didn't

I setup all like in alex_g's post
Version of sane is 1.0.19+cvs from repository

'sane-find-scanner' output:

PHP Code:

# sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. # No SCSI scanners found. If you expected something different, make sure that # you have loaded a kernel SCSI driver for your SCSI adapter. # Also you need support for SCSI Generic (sg) in your operating system. # If using Linux, try "modprobe sg". found USB scanner (vendor=0x03f0, product=0x5617) at libusb:003:002 # Your USB scanner was (probably) detected. It may or may not be supported by # SANE. Try scanimage -L and read the backend's manpage. # Not checking for parallel port scanners. # Most Scanners connected to the parallel port or other proprietary ports # can't be detected by this program.

'scanimage -L' output

PHP Code:

device `hpljm1005:libusb:003:002' is a Hewlett-Packard LaserJet M1120 multi-function peripheral

But 'scanimage -T' command tell me this:

PHP Code:

scanimage: can't resolve symbol 'round'

When use scanner through network, all windows sane frontends is hanging.
Saned process on router is starting and finish shortly.

i don't know what to do next.
Can the scanimage message be an error in source of sane?

Show 40 post(s) from this thread on one page