Controlling (torrent) downloads thru webpage

WAN & LAN Filter,

under WAN to LAN,

Packets(WAN to LAN) not specified will be: DROP (?)

Source IP:
Port Range: 65534
Destination IP: 127.0.0.1
Port Range: 65534
Protocol: TCP

--------

Are these settings ok?

Should i insert something into Virtual Server also.., like when forwarding data to other internal lan adresses..?

To confirm, is there an easy way to see if the active mode is working properly?

Sorry for the noob-question.. but im quite new with these kinda settings, hard to test it from wan side too..

I think that virtual server is appropriate page for setting this on Oleg firmware.

Seems that im not the only one getting into these problems, when searching the forum..

Tried alot of different setups, but i cant get like over 10Kb/s when seeding (average 5-10Kb/s), connected to most 2 peers a time, when seeding a couple of torrents.

Though it seems (like other users have said), that its easier to download.., connected to 60 peers at one time, with 4-500Kb/s average..

Compared to earlier setup with standard XP, utorrent as host/client.. I usually get atleast 100-200Kb/s when seeding a couple of torrents at a time (isp connection is 5mbit down / 5mbit up).

If it was CPU/USB usage that was overloaded on the router, it would increase the seeding when downloading is finished.., but its the same low seed speed..

@oleo, whats ur setup for allowing these rules and so on?

or could u atleast give a hint what can cause the probl..

I've added the port (65534) into Virtual Server, pointing to 127.0.0.1 (localhost), nothing done to WAN to LAN table or config, allowed 'respond ping access from WAN', also have tried to disabled the firewall (usually a 1-2 more peers pops up on each torrent when seeding, but the speeds are almost the same..)

Should i use a manual iptables configuration?

netstat -ln :

tcp 0 0 0.0.0.0:515 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:8008 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:139 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:9100 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:5431 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:65534 0.0.0.0:* LISTEN
tcp 0 0 0.0.0.0:3838 0.0.0.0:* LISTEN
tcp 0 0 :::22 :::* LISTEN
tcp 0 0 :::23 :::* LISTEN


Seeding, uploading to 0 of 0 peer(s), 0.00 KB/s Start: 17 Dec 15:40 End: 18 Dec 04:30 716 seeder(s), 124 leecher(s), 1665 download(s). uploaded: 5.9 MB

You can check your connectivity with telneting to your listening port, eg

Code:

---

telnet  your.outside.router.ip 65534
Connected to your.outside.router.ip
Escape character is '^]'.
help me
Nice try...
Connection closed by foreign host.

---

You should get Nice try... response.

I use another OpenWRT router for routing and QOS only. With lastest buildroot changes it is also possible to run Optware on OpenWRT whiterussian. When disk and swap is functioning just point to http://ipkg.nslu2-linux.org/feeds/op...t/cross/stable
and install uclibc-opt and other packages.

Another news is that there are some Transmission ratecontrol changes in r1255 that shoud stop charshing daemon when ratecontrol is used.

This is all untested though.

Have been trying that, seems that my computer get pointed directly to the local ip of the router, cause if i type my WAN ip directly in explorer i come to Admin login web-interface (without "wan-activated" it). Also if i telnet to it i get login and putty thru ssh also..

I've tested this from outside, telling people to http://my-wan-ip (as i did).., and they get no responce.., same thing happends when they try telnet my-ip.. no responce..

Tried the same with proxy, anonymous web-browser and so on, no responce..

But if i add a forwarding to a ftp server or web server in my lan in Virtual Server, without touching anything else.. it works.. ftp://my-wan-ip is working from outside, for people. Same when browsing http://my-wan-ip from a anonymous web-browser..

Strange.. could it be so that the router senses the packages to the ip and see that it matches the wan-ip and change the traffic directly without linking it out on the wan?

thanks for the reply

1. With ur other box that handling routing and QoS connected, how high speed do u have on ur seeds (total Kb/s) in transmission on ur current one?

Reason of asking.. is why i bought this router is bcause i wanted cheap seeding alternative.., to measure up with my download ratio..

So, if ur alternative with one box routing and delivering packages well, measure up with good torrent handling, seed speeding, it might be worth the $ of an extra box, just for that.., now when i already got one set of wl500gP+250gb usb drive..

2. Do u mean that the alternative whiterussian firmware might get me better speeding handling (whats the difference to oleg's one)?

3. To be sure, is it normal with these seeding speeds at 10Kb/s or could it be accelerated with other torrent apps like enhanced-ctorrent (who also support more active ports).. ?, so i dont have to spend more time getting this to work faster..

Will try the new version r1255 in just a moment.

4. Does these lines looks ok?

/usr/local/sbin/post-firewall

Code:

---

#!/bin/sh
iptables -D INPUT -j DROP
iptables -A INPUT -i $1 -p tcp --syn --dport 65534 -j ACCEPT
iptables -t nat -A PREROUTING -i $1 -p tcp --dport 65534 -j DNAT --to-destination $4:65534
iptables -A INPUT -j DROP

---

With r1255 I have also added --nat-traversal capabilities to daemon. Enabling upnp in router and adding --nat-traversal flag to transmission_watchdog could help with some router config issues.

Code:

---

  transmissiond -p ${LISTENING_PORT} \
        --nat-traversal \
        -w ${WATCHDOG} \
        -u ${UPLOAD_SPEED} \
        -d ${DOWNLOAD_SPEED} \
        -i ${PIDFILE}  ${ACTIVE}

---

Regarding QOS I think that it is nice to throtle application packets. But this application level throtling will never help when user is brouwsing on busy line. For this QOS and packet prioritizing like L7 is needed. See http://vonage.nmhoy.net/qos.html for explanations.

Comparing Oleg and OpenWRT QOS services shows, that Oleg wondershaper is inferior to NBD QOS in OpenWRT although both could be used, but some problems go deep into kernel and that cannot be easily resolved. The problem with OpenWRT is that they did not concentrate much on external storrage for routers as Oleg did.

Thanks,

added this line into transmission.cgi, and Enabled UPnP under IP Config - Miscellaneous (witch was already enabled), Web-Interface (oleg).

Still same, bad seeding, but now more peers found!

Instead of an average of 2 peers connected out of 6 detected of 6 seeding torrents, is now 8 peers connected of 15 detected.

Speed is still low, but slightly increased to about 25Kb/s..

Funny thing is, just after i boot the router and access the script, does transmission show about 0 out of 34, 10, 8 peers on some of the torrents.

After hitting update 5 secs later they all goes down to 1 of 1, 2 of 2, 3 of 5 and so on..

Strange

EDIT: After some waiting Upload seed speeds goes now up to 70Kb/s, download also increased speed from 5Kb/s to 50Kb/s (1 to 5 peers)

Which feed are you using ?

Quote:

---

Originally Posted by oleo

With lastest buildroot changes it is also possible to run Optware on OpenWRT whiterussian. When disk and swap is functioning just point to http://ipkg.nslu2-linux.org/feeds/op...t/cross/stable
and install uclibc-opt and other packages.

---

So u mean setting up transmission on a OPENWRT whiterussian based wl500gP could be a better alternative for torrent client use.. ?

Quote:

---

Originally Posted by calebz

Which feed are you using ?

---

How do u mean feed?

the thing you download stuff from via ipkg.
There is wl500g and olegs feed.
Check what you got there /opt/etc/ipkg.conf

Aha, i used olegs one from scratch, all packets from there..

Well I dont think its soft related. My Upload is actually killing my connection here.

What seeding speeds are u experiencing?

What model, WL500gP?, firmware?

I have tested r1255 with limited upload/download and experienced occassional daemon crash. So until this bug is resolved I do not recommend running daemon with ratecontrol enabled!

Quote:

---

Živjo Oleg, šele zele sem porajtov da si iz Slovenije. Lepo to. :) sn kar mal ponosen, da se najde kakšen Slovenec, ki pripomore za javno dobro. Sem porajtal, ko sem videl, da vlečeš dol čebelico majo, na grafu se vidi :)
Kako to da si se lotil tega projekta? Vsaka ti čast. :rolleyes:

---

When i click Log i can't see graph. I get error:
Creating graph...
/opt/share/www/cgi-bin/transmission.cgi: /opt/share/www/cgi-bin/transmission.cgi: 624: /opt/bin/gnuplot: not found

But i have gnuplot installed.

Code:

---

[admin@SkupniDisk root]$ ipkg install gnuplot
Package gnuplot (4.0.0-1) installed in root is up to date.
Nothing to be done
Successfully terminated.

---

I am also now getting this error:
http://img486.imageshack.us/img486/2931/transmm8.jpg

But the folder exists

This is normal respoonse!

Press Pause once. Then Watchdog and Update after while.


/opt/bin/gnuplot not found problem:
If you are using http://ipkg.nslu2-linux.org/feeds/op.../cross/stable/

package feed. then is also necessary to instal uclibc-opt package as this is base package for all packages.

Calebz Is also testing Transmission on Xwrt (OpenWRT for mere mortals).

Now i am getting this error
Creating graph...
Segmentation fault

Quote:

---

Originally Posted by Urosh

Now i am getting this error
Creating graph...
Segmentation fault

---

Create 512MB swap. Partition (recomended) or file (tryout resort).

Code:

---

dd if=/dev/zero of=/tmp/harddisk/swap count=1024000
mkswap /tmp/harddisk/swap
swapon /tmp/harddisk/swap

---

I am getting:

/opt/bin/gnuplot: can't load library 'libuClibc++.so.0'

And under status

.status not found for /tmp/harddisk/torrent/work/kubuntu-6.10-dvd-i386.iso/kubuntu-6.10-dvd-i386.iso.torrent Start: 27 Dec 18:10

But the torrent file is there.

Code:

---

[admin@SkupniDisk work]$cd /tmp/harddisk/torrent/work/kubuntu-6.10-dvd-i386.iso
[admin@SkupniDisk kubuntu-6.10-dvd-i386.iso]$ ls
kubuntu-6.10-dvd-i386.iso.torrent
[admin@SkupniDisk kubuntu-6.10-dvd-i386.iso]$

---

:( :confused:

gnuplot 4.2rc2 needs libuclibc++ package!

I do not recommend the latest gnuplot 4.2 as it has some strange problems.
Please downgrade with the following commands.

Code:

---

ipkg remove -force-depends gnuplot
cd /tmp/harddisk
wget http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/gnuplot_4.0.0-1_mipsel.ipk
ipkg install gnuplot_4.0.0-1_mipsel.ipk

---

If you are using ipkg-opt package then one can use

Code:

---

ipkg install -force-downgrade gnuplot_4.0.0-1_mipsel.ipk

---

If you do not get .status files then pres Update and see what happens.

calebz promissed _noob_ wiki page how to prepare Optware for X-Wrt.org firmware and how to install Transmssion.

I am confirming Oleo's post. The downgraded version of gnuplot solved the problems I had with drawing the graph.

gnuplot_4.2.rc2-2_mipsel.ipk solves problem with graphing.

Hi oleo,
I had some trouble to make the script work with transmission, because it seems that (at least here) transmissiond only seems to work in the background if called with the "-v" switch. So I changed the script to call transmissiond in a screen session:

Code:

---

/opt/bin/screen -d -m transmissiond -v 1 -p ${LISTENING_PORT} \
-w ${WATCHDOG} \
-u ${UPLOAD_SPEED} \
-d ${DOWNLOAD_SPEED} \
-i ${PIDFILE} ${ACTIVE}

---

I also changed the _fetch() function, because some download URLs have nothing to do with the torrent to download and even crash transmissiond, if special characters are in the name. I now extract the name of the download from the torrent and change some characters.

Code:

---

_fetch()
{
    TORRENT=$(echo "${FETCH}" | sed 's|%20| |g;s|%3A|:|g;s|%2F|/|g;s|%3F|?|g;s|%3D|=|g;s|%26|\&|g;s|%5B|\[|g;s|%5D|\]|g;s|%28|(|g;s|%29|)|g;s|%7B|{|g;s|%7D|}|g;s|%25|%|g')
#    echo "<p>Fetching ${TORRENT}</p>"
    echo "Source: " ${SOURCE}
#    wget --quiet -P ${SOURCE} "${TORRENT}"  ||  echo "<p>wget ${TORRENT} failed</p>"
    wget --quiet -O /opt/tmp/dl.torrent "${TORRENT}" || echo "<p>wget ${TORRENT} failed</p>"
#    DLTARG=`btcheck /opt/tmp/dl.torrent | awk '{if($0~/cacheopen/) print substr($0,11,index($0,".")-11)".torrent"}'|sed -e 'y/\\//-/'`
    DLTARG=`btlist /opt/tmp/dl.torrent | awk '{if($0~/name/)name=sprintf("%s",substr($0,index($0,":")+2))}END{print name}' | sed -e 'y/./_/' -e 'y/\\//\_/'`
 echo "DLTARG=" ${DLTARG}
    cp /opt/tmp/dl.torrent "${SOURCE}/${DLTARG}.torrent"
    rm -f /opt/tmp/dl.torrent
}

---

It's only a hack, but if somebody likes it...

BTW: If I don't want to put my torrent directory into /opt/share/www, how can I access it via the web interface? And for what exactly are the directories "source" and "target"? Everything that I download, suspend or remove is in the "work" directory.

Darkstar.

Quote:

---

Originally Posted by oleo

gnuplot_4.2.rc2-2_mipsel.ipk solves problem with graphing.

---

Hi Oleo, gnuplot_4.2.rc2-2 again caused fragmentation error so I had to downgrade once again to gnuplot (4.0.0-1).

with reguards

@Hellish I have running 4.2rc2 but autobuild machine produced broken package. I have tried to resolve this, without a luck. Problem is with generatigh dynamic executable. Next week we are rebuilding the whole repository from scratch and I am hoping that this will succesfully built gnuplot. If building bug will not be spoted then I will downgrade.

@darkstar The problem with you is known if you are running wl500g feed and not oleg. See README.daemon for solution. Fetch is somehow useless command. It could be used for fetching file that you previously saved with web client on some web server. I am considering to disable it.

Thanx Oleo for ur reply. I will be awaiting new version. I had ipkg update;ipkg upgrade in a cron script wich updated my ipkg pakages regularly. I had to suspend that until your next build.
But thanx for your work anyway. The transmission pakage is much better than the old torrenet package.

with regards,

Hell!sh

I looks like http://trac.nslu2-linux.org/optware/changeset/5097 finally solved gnuplot problems.

Some updated info for installing Transmission on Xwrt (OpenWRT) is found here

Quote:

---

Originally Posted by Darkstar

I also changed the _fetch() function, because some download URLs have nothing to do with the torrent to download and even crash transmissiond, if special characters are in the name. I now extract the name of the download from the torrent and change some characters.

Code:

---

_fetch()
{
    TORRENT=$(echo "${FETCH}" | sed 's|%20| |g;s|%3A|:|g;s|%2F|/|g;s|%3F|?|g;s|%3D|=|g;s|%26|\&|g;s|%5B|\[|g;s|%5D|\]|g;s|%28|(|g;s|%29|)|g;s|%7B|{|g;s|%7D|}|g;s|%25|%|g')
#    echo "<p>Fetching ${TORRENT}</p>"
    echo "Source: " ${SOURCE}
#    wget --quiet -P ${SOURCE} "${TORRENT}"  ||  echo "<p>wget ${TORRENT} failed</p>"
    wget --quiet -O /opt/tmp/dl.torrent "${TORRENT}" || echo "<p>wget ${TORRENT} failed</p>"
#    DLTARG=`btcheck /opt/tmp/dl.torrent | awk '{if($0~/cacheopen/) print substr($0,11,index($0,".")-11)".torrent"}'|sed -e 'y/\\//-/'`
    DLTARG=`btlist /opt/tmp/dl.torrent | awk '{if($0~/name/)name=sprintf("%s",substr($0,index($0,":")+2))}END{print name}' | sed -e 'y/./_/' -e 'y/\\//\_/'`
 echo "DLTARG=" ${DLTARG}
    cp /opt/tmp/dl.torrent "${SOURCE}/${DLTARG}.torrent"
    rm -f /opt/tmp/dl.torrent
}

---

It's only a hack, but if somebody likes it...

---

Hi, try this instead of your hack :-)

Code:

---

[wl-500gp]# FETCH="%2FfolderScreen%3FsessionId%3D%26welcome%3D1"
[wl-500gp]# TORRENT=`echo $FETCH |sed 's/%/\\\\x/g'`
[wl-500gp]# TORRENT=`echo -e "$TORRENT"`
[wl-500gp]# echo $TORRENT
/folderScreen?sessionId=&welcome=1

---

Included this escaping in latest source. Tnx for hint.

Quote:

---

Originally Posted by oleo

Included this escaping in latest source. Tnx for hint.

---

:-)
I started to improve the torrent.cgi script and now I found the transmission. Thanks for it.

Code:

---

[maros@wl-500gp tmp]$ sh -x /opt/share/www//cgi-bin/transmission.cgi
+ . /opt/etc/transmission.conf
+ SOURCE=/tmp/harddisk/torrent/source
+ WORK=/tmp/harddisk/torrent/work
+ TARGET=/tmp/harddisk/torrent/target
+ MAILOPT=-smail.somedomain.com -f
+ USER=nobody
+ GROUP=root
+ DATE_FORMAT=%d %h %H:%M
+ PIDFILE=/opt/var/run/transmission.pid
+ ACTIVE=/tmp/harddisk/torrent/active-torrents.txt
+ HOME=/tmp/harddisk/torrent
+ WATCHDOG=300
+ LISTENING_PORT=65534
+ UPLOAD_SPEED=40
+ DOWNLOAD_SPEED=-1
+ SYSLOG=/opt/var/log/messages
+ AUTOSEED=YES
+ GNUPLOT=/opt/bin/gnuplot
+ GNUPLOT_COMMAND=/tmp/harddisk/torrent/work/transfer.gnuplot
+ GNUPLOT_DATA=/tmp/harddisk/torrent/work/transfer.data
+ GNUPLOT_OUTPUT=/opt/share/www/transfer.png
+ HTTP_IMG_LOCATION=../transfer.png
+ TIMEZONE_OFFSET=+3600
+ GREEN=\033[32;1m
+ NORMAL=\033[0m
+ WARN=\033[33;1m
+ BAD=\033[31;1m
+ BOLD=\033[1m
+ GOOD=\033[32;1m
+ PATH=/bin:/sbin:/usr/bin:/opt/sbin:/opt/bin:/usr/sbin
+ export PATH
/opt/share/www//cgi-bin/transmission.cgi: /opt/share/www//cgi-bin/transmission.cgi: 224: Syntax error: redirection unexpected

---

I don't understood this. Row 224 contains only "sleep 5". :confused:

Quote:

---

Originally Posted by maros

[CODE]

I don't understood this. Row 224 contains only "sleep 5". :confused:

---

Bug is in line 88. I should always check it it works. For trivial changes also!
Wait for -5

http://trac.nslu2-linux.org/optware/changeset/5234

Quote:

---

Originally Posted by oleo

Bug is in line 88. I should always check it it works. For trivial changes also!
Wait for -5

http://trac.nslu2-linux.org/optware/changeset/5234

---

Thanks, it works now.

What about a mininova torrents? They are using redirects, but wget doesn't support file name change in this case. So file "14541547" is created in "source" directory and it is not processed.

I!m thinking about:
1) add .torrent if is missing
2) ask user for proper torrent name and rename it
3) parse torrent file for name and rename automatically
4) improve wget to handle redirections properly (it is in wget TODO)

Hello,
Transmission doesn't work for me. I have ASUS 500g Deluxe with Olegs firmware 1.9.2.7-7f and Transmission 0.6+r1378-5. I have installed Transmission, and followed the instructions mentioned in README.daemon: created the directories, set the permissions, copied torrent files to working directory, etc.

When I hit "Watchdog", it displays:

Code:

---

/opt/sbin/transmission_watchdog: /opt/sbin/transmission_watchdog: 301: transmissiond: not found

16:25:04 up 6 min, load average: 0.13, 0.12, 0.05

---

I have swiched to alternate ipkg package feed ran 'ipkg update'. Then I've tried to run 'ipkg install uclibc', but I've got an error:

Code:

---

An error ocurred, return value: 4.
Collected errors:
Cannot find package uclibc.
Check the spelling or perhaps run 'ipkg update'

---

Also I've tried reinstall all packages using:

Code:

---

awk '/^Package:/{system("ipkg install -force-reinstall -force-defaults " $2)}' /opt/lib/ipkg/status

---

but it doesn't help - now if I try to install uclibc i get even more errors:

Code:

---

[admin@siurblys root]$ ipkg install uclibc
Configuring cron
Remember that the system crontab file is "/opt/etc/crontab".
/opt/etc/init.d/S10cron: /opt/etc/init.d/S10cron: 8: /opt/sbin/cron: not found
postinst script returned status 127
ERROR: cron.postinst returned 127
Configuring xinetd
Note that only 192.168.1.0/24 has access in the default configuration
/opt/etc/init.d/S10xinetd: /opt/etc/init.d/S10xinetd: 14: /opt/sbin/xinetd: not found
postinst script returned status 127
ERROR: xinetd.postinst returned 127
Nothing to be done
An error ocurred, return value: 4.
Collected errors:
Cannot find package uclibc.
Check the spelling or perhaps run 'ipkg update'

---

Do you have any sugestions how to make Transmission runing?

I have following packages:

Code:

---

bzip2 - 1.0.4-1 - Very high-quality data compression program
coreutils - 6.7-1 - Bunch of heavyweight *nix core utilities
cron - 4.1-5 - Standard vixie cron, with cron.d addition
expat - 2.0.0-6 - XML Parser library
findutils - 4.2.29-2 - File finding utilities
fontconfig - 2.3.2-4 - Font configuration library
freetype - 2.1.10-4 - Free truetype library
gconv-modules - 2.2.5-6 - Provides gconv modules missing from the firmware.  These are used by glibc's iconv() implementation.
gdbm - 1.8.3-2 - GNU dbm is a set of database routines that use extensible hashing. It works similar to the standard UNIX dbm routines.
gnuplot - 4.2.rc2-5 - Command-line driven interactive data and function plotting utility
ipkg - 0.99.149-2 -
less - 394-3 - Less file browser
libart - 2.3.17-2 - 2-d graphics library.
libcurl - 7.16.0-6 - Curl is a command line tool for transferring files with URL syntax, supporting FTP, FTPS, HTTP, HTTPS, GOPHER, TELNET, DICT, FI
libdb - 4.2.52-3 - Berkeley DB Libraries
libgd - 2.0.33-3 - An ANSI C library for the dynamic creation of images
libjpeg - 6b-2 - collection of jpeg tools
libogg - 1.1.3-3 - Ogg is a multimedia container format.
libpng - 1.2.15-2 - Portable Network Graphics Libraries
libstdc++ - 0.2.0-6 -
libtool - 1.5.10-2 - Library tools.
libuclibc++ - 0.2.2-4 - C++ standard library designed for use in embedded systems
libvorbis - 1.1.2-5 - Ogg Vorbis compressed audio format.
libxml2 - 2.6.27-2 - Libxml2 is the XML C parser and toolkit developed for the Gnome project.
libxslt - 1.1.19-1 - An XML Stylesheet processor based on libxml2
logrotate - 3.7.1-3 - Rotates, compresses, removes and mails system log files.
nano - 2.0.2-1 - A pico like editor
ncurses - 5.6-1 - NCurses libraries
ncursesw - 5.6-1 - NCurses libraries with wide char support.
nload - 0.6.0-2 - Nload is a console application which monitors network traffic and bandwidth usage in real time
openssl - 0.9.7l-3 - Openssl provides the ssl implementation in libraries libcrypto and libssl, and is needed by many other applications and librari
pcre - 6.7-3 - Perl-compatible regular expression library
popt - 1.7-2 - A C library for parsing command line parameters.
readline - 5.2-2 - The GNU Readline library provides a set of functions for use by applications that allow users to edit command lines as they are
rrdtool - 1.2.15-3 - Round-Robin Database tool. Database collator and plotter
transmission - 0.6+r1378-5 - lightweight BitTorrent client and daemon with WWW interface
vsftpd - 2.0.1-7 - ftp daemon with an emphasis on speed and security
xinetd - 2.3.14-6 - Highly configurable, modular and secure inetd
zlib - 1.2.3-2 - zlib is a library implementing the 'deflate' compression system.

---

install uclibc-opt

so simple :)
everything works fine now, thanks!

After the night I hoped to find some downloaded files, but that's what I've found:

• first file (The.Office.S03E14) was downloaded and then dissappeared (was removed?).
• second file (DreamFall.Longest.Journey.2) is stuck :(

Code:

---

Jan 20 23:24:49 transmissiond[692]: Transmission daemon 0.7-svn (1378) started - http://transmission.m0k.org/
Jan 20 23:24:49 transmissiond[692]: Starting torrent /opt/ftp_pub/Torrent/work/-{mininova.org}- The.Office.S03E14.HDTV.XviD-NoTV.[eztv]/-{mininova.org}- The.Office.S03E14.HDTV.XviD-NoTV.[eztv].torrent
Jan 20 23:29:49 transmissiond[692]: Could not open The.Office.S03E14.HDTV.XviD-NoTV.avi in /opt/ftp_pub/Torrent/work/-{mininova.org}- The.Office.S03E14.HDTV.XviD-NoTV.[eztv] (0, -2147483640)
Jan 20 23:32:22 transmissiond[692]: Starting torrent /opt/ftp_pub/Torrent/work/DreamFall.Longest.Journey.2.DVD-PLEX/DreamFall.Longest.Journey.2.DVD-PLEX.torrent
Jan 20 23:36:54 transmissiond[692]: Could not open DreamFall.Longest.Journey.2.DVD-PLEX/plex-d.l.j.2.dvd.r00 in /opt/ftp_pub/Torrent/work/DreamFall.Longest.Journey.2.DVD-PLEX (0, -2147483640)
Jan 21 02:01:46 transmissiond[692]: Stopping torrent /opt/ftp_pub/Torrent/work/-{mininova.org}- The.Office.S03E14.HDTV.XviD-NoTV.[eztv]/-{mininova.org}- The.Office.S03E14.HDTV.XviD-NoTV.[eztv].torrent

---

The transfer graph shows following:
http://farm1.static.flickr.com/121/3...18ee2e.jpg?v=0

Is it normal that there are several transmissiond processes running, although I'm downloading only one torrent (with several files on it) at the moment?

Code:

---

  605 admin    R        452  160  2.1  1.4 top
    3 admin    SWN        0    1  1.9  0.0 ksoftirqd_CPU0
  891 admin    R N    2204  493  1.5  7.3 transmissiond
  159 admin    S        348  153  1.1  1.1 dropbear
  66 admin    S        240    1  0.1  0.7 httpd
  496 admin    R N    2204  493  0.0  7.3 transmissiond
  490 admin    S N    2204    1  0.0  7.3 transmissiond
  495 admin    R N    2204  493  0.0  7.3 transmissiond
  494 admin    S N    2204  493  0.0  7.3 transmissiond
  493 admin    S N    2204  490  0.0  7.3 transmissiond
  328 siurblys S      1088  148  0.0  3.6 smbd
  150 admin    S        492    1  0.0  1.6 nmbd
  160 admin    S        456  159  0.0  1.5 sh
  326 admin    S        364    1  0.0  1.2 upnp
  127 admin    S        328    1  0.0  1.0 syslogd
  105 admin    S        316    1  0.0  1.0 watchdog
  73 nobody  S        256    1  0.0  0.8 dnsmasq
  103 admin    S        256    1  0.0  0.8 pppd
  148 admin    S        252    1  0.0  0.8 smbd
  146 admin    S        232    1  0.0  0.7 busybox_httpd

---