Printable View
I did.
I tried several configurations, switched it to AP-Mode (and station in advanced), SSID is the same as the 500gx has.
As I said, with the Linksys (ok there are only a few parameters to be set) it works.
At the 500gx the 500g has a wireless authorization and gets a fixed IP.
Has no one ever tried this before ?
Best regards !
Matthias
well me, and many othersQuote:
Originally Posted by utratama
I just followed the manual
did you already switch to WDS Only or Hybrid in the Bridge menu ?
and then you have to fill in remote bridge list ofcourse
Hmmm.
I switched the 500gx to Hybrid-Mode.
The 500g is set as AP.
The bad thing is that I cannot access both of them after they have the same SSID at their IP individual IP-adress.
I only then can access the 500gx when I then have resetted the 500g.
Is there a sample configuration for the client (the 500g) side available somewhere ?
I tried both IPs at the 500g: I let the IP at 192.168.1.1 and I also tried 192.168.30.14 and changed the DHCP to a range which didn't conflict with the 500gx IP-range.
It costs so much time and I'm getting nervous....
By the way: The WDS connection with the Linksys also worked with WPA encryption, so the WDS-WPA problem is only an ASUS one..
Best regards,
Matthias
if the wl500g is in AP mode how is it supposed to connect to another network or to be connected from another network ?
switch to HYBRID or WDS at BOTH units
and yes WPA does work with WDS but depends on a specific configuration
Well, I have the similar problem.
Now, i tried make the setting that which can connect to the web configure menu in both LAN & WAN.
after that, i use the http://externalip:8080/ShowWebCam.asp
It seems work fine in still pic. mode with refresh, but only B/W.
And because of my comany installed proxy server, as a result, i can't connect with activeX stream video. sigh! <-- am i right?
At this moment, I would like to have color image, Could any one help to solve the B/W still image mode???
find out which ports are enabled to connect to by your company's firewall (e.g. port 443 should be open so you could try changing port 7777 to 443)Quote:
Originally Posted by RossiKwan
the web interface only allowed to type in the range from 1024 - 65535 in ActiveX Port.Quote:
Originally Posted by Antiloop
Is there any other method to change it to 443?
And after upgrade firmware to 1.9.2.7-CR4, the still image mode is colourful right now.
Hello
I have two asus wl500g that I wish associated with usb webcams in order to use it as wifi webcams
I wish "to connect" these webcams to my existing network wifi (based on a router wifi netgear)
Is this possible ?
How configure the two asus routers ?
Hi,
I have a Philips Webcam PCVC680 working on my ASUS WL-500g but
can only select between 160x120 and 320x240 but not the maximum of the camera which is 640x480.
Do I have any chance???
And how can I change setting like white Balance, Frame Rate etc??
Thanks
Martin
Hi specialists,
I´m new to this forum, but hopefully searched enough (through this forum) to come up with the following question:
Does anyone have any experience with one of the following USB webcams:
Philips, funcam, DMVC 300k/00
noname, using SPCA561.sys driver
?
So far I was not able to get one of em work with my WL-500g.
If not, How may support for one of those (preferably the Philips one) be 'implemented' into such custom-firmware? Is this possible at all?
hardware used: WL-500g-deluxe with 1940 firmware.
Thanks in advance,
Klaus
Using Oleg's firmware (BIG thanks to oleg for this excellent work!!!) I could get some more information on the Philips camera (at least):
For me it looks as if at least the manufacturer gets recognized (' registered new driver Philips webcam') but the driver is not (yet ?) capable of handling that special type of camerak with the router? Thanks in advance.Code:Jan 1 00:00:55 kernel: hub.c: new USB device 01:02.0-2, assigned address 2
Jan 1 00:00:55 kernel: usb.c: USB device 2 (vend/prod 0x471/0x321) is not claimed by any active driver.
Jan 1 00:00:55 USB webcam: attached
Jan 1 00:00:58 kernel: pwc Philips PCA645/646 + PCVC675/680/690 + PCVC730/740/750 webcam module version 8.12 loaded.
Jan 1 00:00:58 kernel: pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
Jan 1 00:00:58 kernel: pwc the Creative WebCam 5, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
Jan 1 00:00:58 kernel: usb.c: registered new driver Philips webcam
Hi guys,
i've bought the wl-hdd 2.5 some weeks ago and i have upgraded the firmware with olegs one. (the newest one, 1.9.2.7-6)
Now i would like to know, which kind of webcams are supported with this version. I've connected two kinds of webcams (typhoon, and one older version of Logitech) but the IE said every time when i clicked on "preview": couldn't connect to server.
Whats wrong?
Am I too stupid, to connect the Webcam, or
did i use the wrong webcam??
:mad:
Thanks
see this for compatible stuff for Oleg based firmware:
http://wl500g.info/forumdisplay.php?f=24
thx antiloop :)
Hi guys,
i am planning to buy a ASUS WL-500g Deluxe and in the future i want to build a home security monitoring system with a one 4-Port USB HUB and two webcams on it...
I know that this router has a two USB ports, but on second port I wants to have USB Flash or USB HDD...
Now what I have is ASUS DC-3120 Webcam and Trust 4-Port USB HUB :-)
Thanx...