[HowTo] Asus RT-N16 (Oleg) - optware the simple way

Printable View

Show 40 post(s) from this thread on one page

09-08-2010, 20:49
Parkinstein

Quote:

Originally Posted by Hanspeter

Can help me somebody ??

-rw-r--r-- 1 admin root 3662 Aug 9 19:57 /tmp/flash.tar.gz
Check saved image and type "/sbin/flashfs commit" to commit changes
.
Committed.
[admin@ASUS /]$ [ "`awk '/SwapTotal/{print($2)}' /proc/meminfo`" -eq 0 ] && mksw
ap /dev/sda1 && swapon /dev/sda1
[admin@ASUS /]$ mount -o noatime -t ext3 /dev/sda2 /opt && mount -o noatime -t e
xt3 /dev/sda3 /mnt
mount: mounting /dev/sda2 on /opt failed: Device or resource busy
[admin@ASUS /]$ [ -n "`mount | sed -n '/\/opt/p'`" ] && [ -n "`mount | sed -n '/
\/mnt/p'`" ] && cd /mnt && wget http://files.wl500g.info/asus/custom/raas/v10/op
t.tar.gz && cd / && tar -xvzf /mnt/opt.tar.gz && cd /opt && wget http://files.wl
500g.info/asus/custom/raas/v10/mnt.tar.gz && cd / && tar -xvzf /opt/mnt.tar.gz
[admin@ASUS /]$ ipkg update
-sh: ipkg: not found
[admin@ASUS /]$ cd /mnt && wget http://rutorrent.googlecode.com/files/rutorrent-
3.0.tar.gz && tar -xvzf rutorrent-3.0.tar.gz
Connecting to rutorrent.googlecode.com (XX.XX.XX.XX:80)
wget: can't open 'rutorrent-3.0.tar.gz': Read-only file system
[admin@ASUS /mnt]$ [ -x /opt/etc/init.d/rc.unslung ] && /opt/etc/init.d/rc.unslu
ng start
[admin@ASUS /mnt]$ #reboot

see before.... /opt not mounted
10-08-2010, 09:12
ecaddict

Quote:

Originally Posted by verjikd

In order to get SABnzbd running (which is installed also using this howto), I needed to do:

ln -s /opt/lib/libreadline.so.6.1 /opt/lib/libreadline.so.5

I suspect that for Zussaweb/Hellanzb this is needed as well.

Thank you, I've added that line to the install script.
10-08-2010, 09:32
ecaddict

Quote:

Originally Posted by Hanspeter

Can help me somebody ??

mount: mounting /dev/sda2 on /opt failed: Device or resource busy

Try to figure out with mount and cat /etc/fstab commands why the mount fails.

Have the format commands (mke2fs) run OK?
10-08-2010, 10:13
Hanspeter

I have copy all what i see on the terminal

echo.pdf - 43.8 Kb

thanks for help
10-08-2010, 10:44
ecaddict

Quote:

Originally Posted by Hanspeter

I have copy all what i see on the terminal

echo.pdf - 43.8 Kb

thanks for help

What's the capacity of the USB storage that you use (I have the feeling that it's too small as already creating of partitions fail)? It should be bigger than 2GB as 256M is used for swap and 1GB for /opt and the rest for /mnt.

Btw I'll extend the tutorial to mention this.
10-08-2010, 11:33
Hanspeter

jo thats the problem ;)

thank you for you help
10-08-2010, 21:55
verjikd

SabNZB and HellaNZB not working well

I've tried both SabNZB and HellaNZB, installed with this howto. Both have problems at my setup:
- SabNZB crashes when the webinterface is used. Downloading works, however without a webinterface it is inconvenient

- HellaNZB stalls after a while, mostly after working for some quarters of an hour. Only restarting helps. The log file doesn't offer useful info. On internet it shows that stalling of Hellanz happens more on different platforms (especially earlier versions).
Currently I am using this "work-around" (quite drastic, I must say). In cron.hourly I've put an executable script with this contents:
killall python2.5
sleep 10
/opt/bin/startHellaNZB

If others experience these problems too, a warning in the howto is advisable.

I am using:RT-N16-1.9.2.7-rtn-r1799.trx of the 15th of July by the way. I haven't tried newer versions of OLEG firmware
11-08-2010, 09:12
ecaddict

Most probably it has nothing to do with the firmware, but more with dependent libraries etc.
What you could do is upgrading packages with ipkg install <pkg name> (Don't forget to save /opt/etc before doing so!)

E.g. ipkg install python25 py25-hellanzb

You can check installed packages with ipkg list_installed

If you download the .ipkg file (e.g. with wget) from http://ipkg.nslu2-linux.org/feeds/op.../cross/stable/ you can look into it with mc (just enter when on the file) and check dependent packages in control file.

E.g.

Code:

cd /mnt && wget http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/py25-hellanzb_0.13-2_mipsel.ipk

(set the version number at the end to the actual version)

If you figure out what has to be changed I'll fix it in the install script.
11-08-2010, 20:20
verjikd

I will try that and report.

I found out that using an own username instead of admin (as prescribed in the tutorial) gives problems. For example cron doesn't work, as it is based on admin as username to work. My bad... :(
I hope this won't cause any more troubles. Can't be sure now that problems like I have with hellanzb and sabnzb are caused by that :mad:

I also had to tune mediatomb, in order to get it working. Also there a username is needed for good behaviour.....:(
15-08-2010, 16:19
verjikd

@ecaddict
Instead of installing some current versions of libraries, I've done a full ipkg update and ipkg upgrade. I did answer all the questions about changing appr. 10 config files with No.

I like the result: midnight commander works now :D!

SABnzbd however stills quits with a segmentation fault directly after opening the web control page :confused:

For the rest I see no changes in behaviour. Like MC more programs might be affected with old libraries/packages. I would advise people to do ipkg upgrade in de howto, right after the ipkg update. If they answer all answers with no and change the conf-file for light-httpd, they have a better system!
25-08-2010, 05:58
krajicek

Logs to email support

Hi,

[not sure if this is the correct thread if not, admin, please move it.]

just bought RT-N16 router and flashed latest Oleg's fw on it so i'm pretty new to these things.
on the old router with fixed firmware i had "sent logs to email" option which sent logfile each hour to specified email address.

is it possible to have something similar on RT-N16 with Oleg's fw - i know that it probably needs some custom script - but hopefully somebody already created something similar

thank you in advance
krajicek
19-11-2010, 19:53
SlawekW

rTorrent problem with memory

I have RT-N16 with latest Oleg firmware (1.9.2.7-rtn-r2274).
I did configuration follow to ecaddict's manual.

But I have a problem with rtorrent: the error [File chunk write error: Cannot allocate memory.] after few minutes from start router.
I only have a few torrents (less than 10).

What is wrong and how do I fix it?

Thanks,

Slawek
20-11-2010, 10:56
wpte

Quote:

Originally Posted by SlawekW

But I have a problem with rtorrent: the error [File chunk write error: Cannot allocate memory.] after few minutes from start router.
I only have a few torrents (less than 10).

Sounds like a diskspace problem, if not:

Do you have swap space?
are you overclocking the router?
20-11-2010, 11:07
SlawekW

Quote:

Originally Posted by wpte

Sounds like a diskspace problem, if not:

Do you have swap space?
are you overclocking the router?

Rather, it is not a problem with the disc capacity:

Code:

[admin@Router ]$ df Filesystem 1K-blocks Used Available Use% Mounted on rootfs 5248 5248 0 100% / /dev/root 5248 5248 0 100% / devfs 63276 0 63276 0% /dev tmpfs 63276 200 63076 1% /tmp /dev/sda3 479478544 50636612 404485788 12% /mnt /dev/sda2 988244 279236 658808 30% /opt

so I swap space:

Code:

[admin@Router /]$ free total used free shared buffers cached Mem: 126552 124564 1988 0 540 96956 -/+ buffers/cache: 27068 99484 Swap: 257000 188 256812

The router has a standard clock.

Thanks :)
23-11-2010, 14:13
wpte

Quote:

Originally Posted by SlawekW

Rather, it is not a problem with the disc capacity:

Code:

[admin@Router ]$ df Filesystem 1K-blocks Used Available Use% Mounted on rootfs 5248 5248 0 100% / /dev/root 5248 5248 0 100% / devfs 63276 0 63276 0% /dev tmpfs 63276 200 63076 1% /tmp /dev/sda3 479478544 50636612 404485788 12% /mnt /dev/sda2 988244 279236 658808 30% /opt

so I swap space:

Code:

[admin@Router /]$ free total used free shared buffers cached Mem: 126552 124564 1988 0 540 96956 -/+ buffers/cache: 27068 99484 Swap: 257000 188 256812

The router has a standard clock.

Thanks :)

hmm... yes it seems fine.
Do you also experience the same problem with just 1 torrent running?
Maybe you could try transmission as well, for the RT-N16 it works just as fast as my pc:)

Show 40 post(s) from this thread on one page