WL500gPv2 and webcam

any wiki how to config a web cam on WL-500gP with oleg firmware?

Hi folks,

I've just been searching the net, trying to get the above camera working with my wl500gp with Oleg's FW.

Can anyone plz give me a hint on how to install spca5xx (LE ?) on it ?

Installing ipkg install wget http://weimarnetz.de/ipkg/packages/s...m_1_mipsel.ipk

fails due to kmod-videodev and libpthread are missing... where can I get it ?

Thanx for a hint and/or tutorial :-)

Thx

Zigster

Have you read this thread?

http://wl500g.info/showthread.php?t=6734

the camera is not supported by the router

Hello

I have a webcam with he following chractristics as it was detected by Linux:
QuickCam USB, Sensor HDCS-1000/1100.

Can I connect it to WL500gP and how?

KR

Ïî÷òè íàøåë îòâåò íà ìîé âîïðîñ. Ýòî qce-ga.sourceforge.net. Ó ìåíÿ èìåííî ýòîò êàì. Åñëè áû êòî íèáóäü ïîìîã ìíå âáèòü ýòîò äðàéâåð â ìîé Àñþñ, à òî ÿ òàê ñåáå ñ Ëèíóêñîì âîîáùå, à ñ Àñþñîì â ÷àñòíîñòè.

Hello

I've got webcam SPCA561, i read all the posts about installing this, and still don't know how to do it :(
i don't have video device - > /dev/video
after insmod my camera is not recognized
please help me

Wl-500gp V1, newest Oleg firmware

Dear all,

I have enable the WebCam to be accessed by WAN, my boardband upload speed is 128Kbps (about 14K/s) , whenever it takes me 9 seconds to refresh the image of video. Anyway, I have tried to capture the image from the video, it is a 225Kb bitmap file (If I save the bitmap file to jpg, it becames 47Kb file only). Anybody know that if the video have any compression in the transmittion process from Lan to Wan? Or any way to tune up the speed of video's refresh rate?

cma

Hi everybody.
After months for searching a compatibile webcam with my 500gp, firmware .10 Oleg i finally find a old Philips.
Cam is recognized and working but i run in this problem, cpu is sky high and in log get megs fat with folowing error :

Jan 1 02:00:06 kernel: hub.c: new USB device 01:03.0-1, assigned address 2
Jan 1 02:00:06 kernel: usb.c: USB device 2 (vend/prod 0x5a9/0x518) is not claimed by any active driver.
Jan 1 02:00:06 USB webcam: attached
Sep 8 18:46:43 dropbear[147]: Running in background
Sep 8 18:46:44 kernel: usb.c: registered new driver spca5xx
Sep 8 18:46:44 kernel: drivers/usb/spca5xx.c: spca5xx driver 00.60.00 registered
Sep 8 18:46:53 ntp client: Synchronizing time with time.nist.gov ...
Sep 8 18:46:53 kernel: usb.c: registered new driver ov51x
Sep 8 18:46:53 kernel: ov51x.c: USB OV518 video device found
Sep 8 18:46:53 kernel: Adding Swap: 506008k swap-space (priority -1)
Sep 8 18:46:53 kernel: ov51x.c: Device revision 1
Sep 8 18:46:54 kernel: ov51x.c: Compression required with OV518...enabling
Sep 8 18:46:54 e2fsck: /dev/discs/disc0/part2: clean, 10080/125696 files, 40355/251015 blocks
Sep 8 18:46:54 e2fsck: /dev/discs/disc0/part3: recovering journal
Sep 8 18:46:56 kernel: ov51x.c: Sensor is an OV66308AF
Sep 8 18:46:57 kernel: ov51x.c: Device at usb-01:03.0-1 registered to minor 0
Sep 8 18:46:57 kernel: ov51x.c: v1.65-1.12-mark : ov51x USB Camera Driver
Sep 8 18:46:57 kernel: ov511_decomp.c: v1.6 : OV511 Decompression Module
Sep 8 18:46:57 kernel: ov518_decomp.c: v1.3 : OV518 Decompression Module
Sep 8 18:46:58 kernel: ov51x.c: ERROR: urb->status=-63: Buffer error (overrun)
Sep 8 18:46:58 kernel: ov51x.c: ERROR: urb->status=-63: Buffer error (overrun)

The error appear like 1 per second, this way my log growing to 10M in two days ...
Any help here ?

LE : is normal to have two decompression modules registered ? (ov511_decomp.c v 1.3 and v 1.6)

buffer overrun... I guess there is no protection in it.
the problem is, when this happens, you're webcam might be a bit broken.
the sky high cpu useage can be because of the webcam monitor.
has dcam a high usage?
I use a limiter for the max fps it captures, to make sure it doesnt get too high:)

Me too.
Months of searching for webcam and no success.
At Internet auction sites a lot of new, old webcams.
Nobody knows board code name.

Just for tests, pls name and give web link to working webcam from ebay
or another place.

Darius

The "rcamd" in fact raise cpu to 100% and keep there until i disconnect the camera.
All i get in logs is the buffer error ...
The image from camera is ok, with no artefacts.
I dont know if is normal, the 100% use of cpu is if camera is accessed or not, when i plug the cam, no matter wich settings/resolution i use ...
I use 2 sec refresh time .

This webcam still available on ebay works for sure:

http://cgi.ebay.at/Webcam-Philips-To...QQcmdZViewItem

I have also successfully in operation:

PCVC680K
PCVC840K

Nobody have an ideea ?
Cam is a PCVC680K.

Hi,
Use pwc driver that comes with the Asus. Ov51x or spca5xx driver will NOT work with PCVC680K. Cheers.