[HowTo] Install and configure Oleg's firmware

Printable View

Show 40 post(s) from this thread on one page

08-02-2009, 22:18
bodvar

which samba supports norwegian characters?

I did the setup using Oleg's integrated version of samba. But it seems it doesn't support some norwegian characters (which are æ ø å, Æ Ø Å). Strangely, only ø and Ø is not supported. Samba in the original firmware actually supported all of them.

Should this work with the integrated samba version, or do you know if the custom samba setup can support this?
-------------------------------

UPDATED: It seems that support for dos codepage 865 is needed, which the integrated samba version seems to lack. Does the custom samba version support that? If so, how can it be set up?
10-02-2009, 13:58
mihaidenis

Thank you Wengi

Your tutorial is great (i`m for the first time in linux world).

I follow your instruction and everything was ok.

Except a small error in in your TRANSMISSION (The torrent Client) script.

Transmission never start automatically at router reboot.

Your:

vi /tmp/harddisk/transmission/config/settings.json

is like this:

#!/bin/sh
#
# Startup script for transmission-daemon

case $1 in
start)
# update blocklist
echo "updating blocklist, ~4MB"
cd /tmp/harddisk/transmission/config/blocklists
wget -q http://www.bluetack.co.uk/config/level1.gz
if test -f level1.gz; then
rm level1
gunzip level1.gz
chmod go+r level1
fi
# start transmission
echo "starting transmission"
/opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config
;;

stop)
if [ -n "`pidof transmission-daemon`" ]; then
kill -9 `pidof transmission-daemon`
fi
;;

restart)
$0 stop
$0 start
;;

*)
echo "usage: $0 (start|stop|restart)"
exit 1
esac

Mine is modified like that and it works now at router restart:

#!/bin/sh
#
# Startup script for transmission-daemon

case $1 in
start)
# update blocklist
echo "updating blocklist, ~4MB"
cd /tmp/harddisk/transmission/config/blocklists
wget -q http://www.bluetack.co.uk/config/level1.gz
if test -f level1.gz; then
rm level1
gunzip level1.gz
chmod go+r level1
fi
# start transmission
echo "starting transmission"
/opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config
;;

stop)
if [ -n "`pidof transmission-daemon`" ]; then
kill -9 `pidof transmission-daemon`
fi
;;

restart)
$0 stop
$0 start
;;

*)
echo "usage: $0 (start|stop|restart)"
exit 0
esac

Thanks again for your tutorial.
Takes me more time to understand vi editor than your guide.
11-02-2009, 09:26
wengi

My script works fine here.

What did you change? I do not see the difference.

wengi
11-02-2009, 11:31
kaizen

Quote:

Originally Posted by mihaidenis

exit 1
[...]
exit 0

This is differnce (the only one).
01-03-2009, 01:44
lowie82ph

hi,

how can I limit the simultaneous downloads and uploads in transmission?
where can I specify the target, source and work folders?

thanks.
01-03-2009, 11:30
wengi

See the conf page:
http://trac.transmissionbt.com/wiki/...iles#Overview1

You want to limit the number of connections or the number of active torrents?

wengi
01-03-2009, 14:16
lowie82ph

Quote:

Originally Posted by wengi

See the conf page:
http://trac.transmissionbt.com/wiki/...iles#Overview1

You want to limit the number of connections or the number of active torrents?

wengi

yes, for example I have 5 torrents, I only want 2 active and the 3 are waiting. I can't see that option on the link you provided.
how can I set that?

thanks
02-03-2009, 10:16
wengi

As far as i know it is done manually.
You have to start a torrent manually after another has finished.
The old daemon had this feature but i didnt find it in the new one.

wengi
02-03-2009, 12:53
TheCrow

rtorrent

wengi (sry my english)
tnx for tut.

I try trasmission, is ok...i like it but the speed is slow ~1.5 MB/s, from pc: 4.5-6 MB/s from a local tracker.

u can help me with a tut on rtorrent made by you step-by-step?
maybe the speed on rtorrent is not the same as transmission.
02-03-2009, 13:16
wengi

sorry, no experience with rtorrent.

check your cpu and memory status with "top" when transmission is downloading.
Which hardware do you use?

wengi
02-03-2009, 13:34
TheCrow

wl-500gp V2

PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
225 TheCrow 20 0 6772 6356 2368 R 81.2 21.1 1:47.55 transmission-da
229 TheCrow 15 0 640 640 492 R 3.4 2.1 0:01.55 top
95 TheCrow 9 0 0 0 0 S 3.1 0.0 0:02.99 usb-storage-0
129 TheCrow 9 0 0 0 0 S 0.9 0.0 0:00.43 kjournald
03-03-2009, 00:22
examiner

SLOW or not-working torrents

Hi wengi,

thank you for the great tutorial, I was lost in configuring my WL500W until I found this. :)

However, transmission is very very slow, sometimes it says "Downloading 0 of 0 peers". When I start the same torrent on my PC, it works fine and usually fast.

I have 16Mbit line and on PC I get speeds up to 1MByte/s, but on my WL500W, even with no-limit settings, I don't get more than 50 KB/s.

The most irritating is the fact that some torrents don't work at all, as explained above.

My WL500W is not a router, but it is set as AP only - it acts as any other PC on the network, such as mine, that works ok. Can the Blacklist cause such problems?
03-03-2009, 10:33
wengi

Hi,

one general thing:

YOUR ROUTER IS NOT A PC!
This means that it has about 10% the CPU power of your PC.

As you can see in TheCrow's post transmission is consuming over 80% of cpu power.

Don't expect too much from this little piece of hardware.
I normaly start a max of three torrents and the average dl rate is about 20-30k with my WL-HDD.

Keep cool and relax :cool:

wengi

PS: Maybe other torrent clients are faster, but do not expect them to be much faster!
04-03-2009, 08:46
examiner

OK, I can live with that...:) It is weird thoughm that UL is about 200KB and DL is so slow.

But what about the torrents that dont work at all? Why it says 0 of 0 peers? When I start the same torrent on my PC, it works ok. They both share the same public IP address, but some torrents just do not work on transmission.

It used to be ok at the beginning - i could download anything i wanted, but after some time..

Is there any chance to perform transmission diagnostics?

thx

examiner
04-03-2009, 11:56
wengi

did you update to the latest version of transmission?

ipkg update && ipkg upgrade

wengi

EDIT
Try to disable blacklist to make it faster.
04-03-2009, 13:10
mitku

@wengi, thanks a lot for this great how-to guide. All is perfectly working on my WL-500W router. http://wl500g.info/images/icons/icon14.gif

I copied this guide in one other forum, to spread this knowledge to my friends - HERE. Off course it's with links to this thread and your name. I hope you have nothing against that. Thanks again. http://wl500g.info/images/icons/icon14.gif
05-03-2009, 05:46
TheCrow

transmission

my S90transmission-daemon not starting when i reboot router. How can i resolve that?? pls..
05-03-2009, 08:54
wengi

check content (with vi or nano).
check if executable.

wengi
05-03-2009, 09:15
TheCrow

if i start manualy , workin` ......so is executable...another ideea?

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ ps axf PID TTY STAT TIME COMMAND 1 ? S 0:01 /sbin/init 2 ? S 0:00 [keventd] 3 ? RN 0:00 [ksoftirqd_CPU0] 4 ? S 0:00 [kswapd] 5 ? S 0:00 [bdflush] 6 ? S 0:00 [kupdated] 7 ? S 0:00 [mtdblockd] 57 ? S 0:00 telnetd 62 ? S 0:00 httpd vlan1 67 ? S 0:00 syslogd -m 0 -O /tmp/syslog.log -S -l 7 68 ? S 0:00 klogd 71 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan 73 ? S 0:00 [dnsmasq] 75 ? S 0:00 [khubd] 83 ? Ss 0:00 lpd 85 ? Ss 0:00 p9100d -f /dev/usb/lp0 0 88 ? Ss 0:00 waveservermain 91 ? Ss 0:00 rcamdmain 95 ? S 0:00 [usb-storage-0] 96 ? S 0:00 [scsi_eh_0] 109 ? Ss 0:00 pppd file /tmp/ppp/options.wan0 112 ? Ss 0:00 infosvr br0 113 ? Ss 0:00 watchdog 115 ? Ss 0:00 \_ ntp 122 ? S 0:00 dropbear 166 ? Ss 0:00 \_ dropbear 167 pts/0 Ss 0:00 \_ -sh 170 pts/0 R+ 0:00 \_ ps axf 148 ? S 0:00 [kjournald] 149 ? S 0:00 [kjournald] 152 ? Ss 0:00 /usr/sbin/vsftpd 159 ? S 0:00 upnp -D -L br0 -W ppp0 [TheCrow@WL-001FC6D7E6E7 root]$

Code:

#!/bin/sh # # Startup script for transmission-daemon case $1 in start) # update blocklist echo "updating blocklist, ~4MB" cd /tmp/harddisk/transmission/config/blocklists wget -q http://www.bluetack.co.uk/config/level1.gz if test -f level1.gz; then rm level1 gunzip level1.gz chmod go+r level1 fi # start transmission echo "starting transmission" /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config ;; stop) if [ -n "`pidof transmission-daemon`" ]; then kill -9 `pidof transmission-daemon` fi ;; restart) $0 stop $0 start ;;
06-03-2009, 07:49
mitku

Quote:

Originally Posted by TheCrow

if i start manualy , workin` ......so is executable...another ideea?...

Is it with the right file name... starting with "S" (for automatic starting scripts at boot time) and number with 2 digits (for priority among starting scripts order) - in this case "S90xxxxx"?
Is it in the right directory "/opt/etc/init.d/"?
06-03-2009, 10:16
TheCrow

Quote:

Originally Posted by mitku

Is it with the right file name... starting with "S" (for automatic starting scripts at boot time) and number with 2 digits (for priority among starting scripts order) - in this case "S90xxxxx"?
Is it in the right directory "/opt/etc/init.d/"?

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ ls /opt/etc/init.d/ S10cron S90transmission-daemon rc.unslung [TheCrow@WL-001FC6D7E6E7 root]$

IS OK?
06-03-2009, 11:00
wengi

Hi,

this is looking good, BUT as we see you have a S10cron which should start cron also.
But it does not as your ps shows some posts ago.

The question in general: Is your rc.unslung starting?

wengi
06-03-2009, 12:00
TheCrow

hmm....how can i know that??

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ cat /opt/etc/init.d/rc.unslung #! /bin/sh # Start/stop all init scripts in /opt/etc/init.d # starting them in numerical order and # stopping them in reverse numerical order # if [ $# -ne 1 ]; then printf "Usage: $0 {start|stop}\n" >&2 exit 1 fi daemons=`echo $(/usr/bin/dirname $0)/S??*` [ $1 = "stop" ] && daemons=`echo $daemons | /usr/bin/tr " " "\n" | /usr/bin/sort -r` for i in $daemons; do # Ignore dangling symlinks (if any). [ ! -f "$i" ] && continue # Write to syslog logger -t rc.unslung "$1 service $i" case "$i" in *.sh) # Source shell script for speed. ( trap - INT QUIT TSTP set $1 . $i ) ;; *) # No sh extension, so fork subprocess. $i $1 ;; esac done [TheCrow@WL-001FC6D7E6E7 root]$
06-03-2009, 13:43
mitku

Also - look for the appropriate rights for "/opt/etc/init.d/" directory... there have to have an execute rights also - for the directory itself, and for files inside.
If it's necessary - do following:

Code:

chown 0:0 -R /opt/etc/init.d chmod 755 -R /opt/etc/init.d

... and then... you know:

Code:

flashfs save && flashfs commit && flashfs enable && reboot
06-03-2009, 13:49
TheCrow

Quote:

Originally Posted by mitku

Also - look for the appropriate rights for "/opt/etc/init.d/" directory... there have to have an execute rights also - for the directory itself, and for files inside.
If it's necessary - do following:

Code:

chown 0:0 -R /opt/etc/init.d chmod 755 -R /opt/etc/init.d

... and then... you know:

Code:

flashfs save && flashfs commit && flashfs enable && reboot

nothing....not starting....:(, only manually start...

it`s ok??

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ cat /opt/etc/init.d/S10cron #!/bin/sh # # Startup script for cron PIDFILE=/opt/var/run/cron.pid case $1 in start) /opt/sbin/cron ;; stop) [ -f ${PIDFILE} ] && kill `cat ${PIDFILE}` ;; *) echo "usage: $0 (start|stop)" exit 1 esac[TheCrow@WL-001FC6D7E6E7 root]$
06-03-2009, 14:34
mitku

Obviously nothing starts from the /opt/etc/init.d
Let we see what are the rights in this directory. Do the following:

Code:

cd /opt/etc/init.d ls -la

... and also let we see what are mounting points on your router:

Code:

mount

... and post the results here.
Did you follow all the steps above at beginning in this thread for USB/hard drive partitioning, mounting points AND file systems (ext3 or ext2)?
06-03-2009, 14:48
wengi

what happens if you do a

Code:

/opt/etc/init.d/rc.unslung start

after restart?
Are transmission and cron running?

There should also be rc.unslung lines in your syslog.

Could you please post the syslog of a boot?

wengi
06-03-2009, 17:16
TheCrow

Quote:

Originally Posted by mitku

Obviously nothing starts from the /opt/etc/init.d
Let we see what are the rights in this directory. Do the following:

Code:

cd /opt/etc/init.d ls -la

... and also let we see what are mounting points on your router:

Code:

mount

... and post the results here.
Did you follow all the steps above at beginning in this thread for USB/hard drive partitioning, mounting points AND file systems (ext3 or ext2)?

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ cd /opt/etc/init.d [TheCrow@WL-001FC6D7E6E7 init.d]$ ls -la total 20 drwxr-xr-x 2 TheCrow root 4096 Mar 6 09:21 . drwxr-xr-x 4 TheCrow root 4096 Mar 6 09:30 .. -rwxr-xr-x 1 TheCrow root 223 Mar 6 14:27 S10cron -rwxr-xr-x 1 TheCrow root 595 Mar 6 14:33 S90transmission-daemon -rwxr-xr-x 1 TheCrow root 642 Mar 6 09:10 rc.unslung [TheCrow@WL-001FC6D7E6E7 init.d]$

Code:

[TheCrow@WL-001FC6D7E6E7 init.d]$ mount /dev/root on / type squashfs (ro) none on /dev type devfs (rw) proc on /proc type proc (rw) ramfs on /tmp type ramfs (rw) usbfs on /proc/bus/usb type usbfs (rw) /dev/discs/disc0/part2 on /opt type ext3 (rw,noatime) /dev/discs/disc0/part3 on /tmp/mnt/disc0_3 type ext3 (rw,noatime) [TheCrow@WL-001FC6D7E6E7 init.d]$
06-03-2009, 17:25
TheCrow

Quote:

Originally Posted by wengi

what happens if you do a

Code:

/opt/etc/init.d/rc.unslung start

after restart?
Are transmission and cron running?

There should also be rc.unslung lines in your syslog.

Could you please post the syslog of a boot?

wengi

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ ps axf PID TTY STAT TIME COMMAND 1 ? S 0:01 /sbin/init 2 ? S 0:00 [keventd] 3 ? RN 0:00 [ksoftirqd_CPU0] 4 ? S 0:00 [kswapd] 5 ? S 0:00 [bdflush] 6 ? S 0:00 [kupdated] 7 ? S 0:00 [mtdblockd] 61 ? S 0:00 telnetd 62 ? S 0:00 httpd vlan1 67 ? S 0:00 syslogd -m 0 -O /tmp/syslog.log -S -l 7 68 ? S 0:00 klogd 71 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan 73 ? S 0:00 [dnsmasq] 75 ? S 0:00 [khubd] 83 ? Ss 0:00 lpd 86 ? Ss 0:00 p9100d -f /dev/usb/lp0 0 89 ? Ss 0:00 waveservermain 91 ? Ss 0:00 rcamdmain 95 ? S 0:00 [usb-storage-0] 96 ? S 0:00 [scsi_eh_0] 120 ? S 0:00 udhcpc -i vlan1 -p /var/run/udhcpc0.pid -s /tmp/udhcp 121 ? Ss 0:00 pppd file /tmp/ppp/options.wan0 124 ? Ss 0:00 infosvr br0 125 ? Ss 0:00 watchdog 127 ? Ss 0:00 \_ ntp 145 ? S 0:00 dropbear 170 ? Ss 0:00 \_ dropbear 171 pts/0 Ss 0:00 \_ -sh 174 pts/0 R+ 0:00 \_ ps axf 157 ? S 0:00 [kjournald] 158 ? S 0:00 [kjournald] 161 ? Ss 0:00 /usr/sbin/vsftpd 168 ? S 0:00 upnp -D -L br0 -W ppp0 [TheCrow@WL-001FC6D7E6E7 root]$ /opt/etc/init.d/rc.unslung start Stopping syslogd: syslogd. Starting syslogd: syslogd. updating blocklist, ~4MB starting transmission

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ ps axf PID TTY STAT TIME COMMAND 1 ? S 0:01 /sbin/init 2 ? S 0:00 [keventd] 3 ? RN 0:01 [ksoftirqd_CPU0] 4 ? S 0:00 [kswapd] 5 ? S 0:00 [bdflush] 6 ? S 0:00 [kupdated] 7 ? S 0:00 [mtdblockd] 61 ? S 0:00 telnetd 62 ? S 0:00 httpd vlan1 68 ? S 0:00 klogd 71 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan 73 ? S 0:00 [dnsmasq] 75 ? S 0:00 [khubd] 83 ? Ss 0:00 lpd 86 ? Ss 0:00 p9100d -f /dev/usb/lp0 0 89 ? Ss 0:00 waveservermain 91 ? Ss 0:00 rcamdmain 95 ? S 0:00 [usb-storage-0] 96 ? S 0:00 [scsi_eh_0] 120 ? S 0:00 udhcpc -i vlan1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc -b 121 ? Ss 0:00 pppd file /tmp/ppp/options.wan0 124 ? Ss 0:00 infosvr br0 125 ? Ss 0:00 watchdog 127 ? Ss 0:00 \_ ntp 145 ? S 0:00 dropbear 170 ? Ss 0:00 \_ dropbear 171 pts/0 Ss 0:00 \_ -sh 219 pts/0 R+ 0:00 \_ ps axf 157 ? S 0:00 [kjournald] 158 ? S 0:00 [kjournald] 161 ? Ss 0:00 /usr/sbin/vsftpd 168 ? S 0:00 upnp -D -L br0 -W ppp0 199 ? S 0:00 /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7 -s 0 216 ? S 0:00 /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config 217 ? S 0:00 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config 218 ? R 0:39 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config [TheCrow@WL-001FC6D7E6E7 root]$
06-03-2009, 19:05
wengi

please post result of

Code:

cat /usr/local/sbin/post-mount

wengi
06-03-2009, 19:14
TheCrow

Quote:

Originally Posted by wengi

please post result of

Code:

cat /usr/local/sbin/post-mount

wengi

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ cat /usr/local/sbin/post-mount #! /bin/sh /opt/etc/init.d/rc.unslung start [TheCrow@WL-001FC6D7E6E7 root]$
06-03-2009, 21:26
mitku

Are all those scripts in /usr/local/sbin/ (and particularly /usr/local/sbin/post-mount) executable?
If not, make them executable:

Code:

chmod 755 -R /usr/local/sbin/
06-03-2009, 21:35
TheCrow

yap... guess that is....tnx :cool: now it`s working....

Code:

[TheCrow@WL-001FC6D7E6E7 root]$ ps axf PID TTY STAT TIME COMMAND 1 ? S 0:01 /sbin/init 2 ? S 0:00 [keventd] 3 ? RN 0:00 [ksoftirqd_CPU0] 4 ? S 0:00 [kswapd] 5 ? S 0:00 [bdflush] 6 ? S 0:00 [kupdated] 7 ? S 0:00 [mtdblockd] 57 ? S 0:00 telnetd 62 ? S 0:00 httpd vlan1 68 ? S 0:00 klogd 71 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan 73 ? S 0:00 [dnsmasq] 75 ? S 0:00 [khubd] 83 ? Ss 0:00 lpd 86 ? Ss 0:00 p9100d -f /dev/usb/lp0 0 89 ? Ss 0:00 waveservermain 91 ? Ss 0:00 rcamdmain 95 ? S 0:00 [usb-storage-0] 96 ? S 0:00 [scsi_eh_0] 120 ? S 0:00 udhcpc -i vlan1 -p /var/run/udhcpc0.pid -s /tmp/udhcp 121 ? Ss 0:00 pppd file /tmp/ppp/options.wan0 124 ? Ss 0:00 infosvr br0 125 ? Ss 0:00 watchdog 127 ? Ss 0:00 \_ ntp 174 ? Ss 0:00 \_ /bin/sh /usr/local/sbin/post-mount 1058/702/104 175 ? S 0:00 \_ /bin/sh /opt/etc/init.d/rc.unslung start 208 ? S 0:00 \_ /bin/sh /opt/etc/init.d/S90transmission-d 218 ? R 0:02 \_ gunzip level1.gz 135 ? S 0:00 dropbear 212 ? Ss 0:00 \_ dropbear 213 pts/0 Ss 0:00 \_ -sh 219 pts/0 R+ 0:00 \_ ps axf 152 ? S 0:00 upnp -D -L br0 -W ppp0 169 ? S 0:00 [kjournald] 170 ? S 0:00 [kjournald] 173 ? Ss 0:00 /usr/sbin/vsftpd 200 ? S 0:00 /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7 [TheCrow@WL-001FC6D7E6E7 root]$ ps axf PID TTY STAT TIME COMMAND 1 ? S 0:01 /sbin/init 2 ? S 0:00 [keventd] 3 ? SN 0:00 [ksoftirqd_CPU0] 4 ? S 0:00 [kswapd] 5 ? S 0:00 [bdflush] 6 ? S 0:00 [kupdated] 7 ? S 0:00 [mtdblockd] 57 ? S 0:00 telnetd 62 ? S 0:00 httpd vlan1 68 ? S 0:00 klogd 71 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan 73 ? S 0:00 [dnsmasq] 75 ? S 0:00 [khubd] 83 ? Ss 0:00 lpd 86 ? Ss 0:00 p9100d -f /dev/usb/lp0 0 89 ? Ss 0:00 waveservermain 91 ? Ss 0:00 rcamdmain 95 ? S 0:00 [usb-storage-0] 96 ? S 0:00 [scsi_eh_0] 120 ? S 0:00 udhcpc -i vlan1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc -b 121 ? Ss 0:00 pppd file /tmp/ppp/options.wan0 124 ? Ss 0:00 infosvr br0 125 ? Ss 0:00 watchdog 127 ? Ss 0:00 \_ ntp 135 ? S 0:00 dropbear 212 ? Ss 0:00 \_ dropbear 213 pts/0 Ss 0:00 \_ -sh 226 pts/0 R+ 0:00 \_ ps axf 152 ? S 0:00 upnp -D -L br0 -W ppp0 169 ? S 0:00 [kjournald] 170 ? S 0:00 [kjournald] 173 ? Ss 0:00 /usr/sbin/vsftpd 200 ? S 0:00 /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7 -s 0 223 ? S 0:00 /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/conf 224 ? S 0:00 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/ 225 ? R 0:04 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmiss [TheCrow@WL-001FC6D7E6E7 root]$
06-03-2009, 23:47
examiner

Quote:

Originally Posted by wengi

did you update to the latest version of transmission?

ipkg update && ipkg upgrade

wengi

ok...the easiest solution is just right...;-) after upgrade i have like 256KB/s download, lots of peers...perhaps something with the version of transmission i had...:)

thanx
07-03-2009, 19:59
TheCrow

how can i acces my router with winscp.
when i try to connect...: "Cannot initialize SFTP protocol. Is the host running a SFTP server?"
i know i have to make soething on router but i don`t know:(
07-03-2009, 21:12
al37919

either use scp or:

PHP Code:

ipkg install openssh-sftp-server
07-03-2009, 21:44
TheCrow

Quote:

Originally Posted by al37919

either use scp or:

PHP Code:

ipkg install openssh-sftp-server

works....tnx:)
09-03-2009, 10:24
Etor

Permission denied when i try to install new package

[admin@ASUS_160GB ipkg]$ ipkg update
Downloading http://ipkg.nslu2-linux.org/feeds/op...le/Packages.gz
sh: wget: Permission denied
An error ocurred, return value: 1.
Collected errors:
ipkg_download: ERROR: Command failed with return value 127: `wget -q -P /opt/ipkg-4TwonM http://ipkg.nslu2-linux.org/feeds/op...le/Packages.gz'

[admin@ASUS_160GB ipkg]$ ipkg upgrade
sh: rm: Permission denied
Nothing to be done
Successfully terminated.

When i try to install unrar for example:
[admin@ASUS_160GB ipkg]$ ipkg install unrar
Package unrar (3.7.8-1) installed in /opt/ is up to date.
sh: rm: Permission denied
Nothing to be done
Successfully terminated.

Please why I always see Permission denied? I am logged as admin and df shows:
[admin@ASUS_160GB ipkg]$ df
Filesystem Size Used Avail Use% Mounted on
rootfs 3.0M 3.0M 0 100% /
/dev/root 3.0M 3.0M 0 100% /
/dev/discs/disc0/part2
966M 103M 814M 12% /opt
/dev/discs/disc0/part3
916G 257G 613G 30% /tmp/mnt/disc0_3
09-03-2009, 11:14
wengi

Hi,

did this work at any time or is it a permanent error since you installed the router?

wengi
09-03-2009, 11:44
Etor

Quote:

Originally Posted by wengi

Hi,

did this work at any time or is it a permanent error since you installed the router?

wengi

Hi wengi,
i finished this tutorial succesfully so it worked before. But now after month of using this happened and Im not aware about anything what I did. Restart doesnt help.

Show 40 post(s) from this thread on one page