Your stick does not contain partition table, it's formated like a big floppy disk. It's not supported by wl500g this way. You've to run fdisk and create a partition and reformat the stick.Quote:
Originally Posted by yeager
Printable View
Your stick does not contain partition table, it's formated like a big floppy disk. It's not supported by wl500g this way. You've to run fdisk and create a partition and reformat the stick.Quote:
Originally Posted by yeager
is that possible, i always have a problem, now i cannot format the stick
[admin@ (none) root] $ ls -l /dev/discs/disc0/
brw------- 1 admin root 8, 0 Jan 1 00:00 disc
brw------- 1 admin root 8, 0 Jan 1 00:00 part1
brw------- 1 admin root 8, 0 Jan 1 00:00 part2
brw------- 1 admin root 8, 0 Jan 1 00:00 part3
brw------- 1 admin root 8, 0 Jan 1 00:00 part4
[admin@ (none) root] $
[admin@ (none) root] $fdisk /dev/discs/disc0/disc
Unable to read /dev/discs/disc0/disc
[admin@ (none) root] $
[admin@ (none) root] $fdisk /dev/scsi/host0/bus0/target0/lun0/disc
Unable to read /dev/scsi/host0/bus0/target0/lun0/disc
any idea?
:eek: :confused: :mad:
when i explore this transcend usb stick under windows with User-mode FS-explorer i see this
HDD1
|
[unknown](544.32Gb)
[unknown](923.17Gb)
[unknown](923.17Gb)
[unknown](0.02Gb)
and when i put the kingston stick
HDD1
|
[unknown](0.6Gb)
but this not recognize asus
cpu probe
prom init
cpu report
CPU revision is: 00024000
Loading BCM4710 MMU routines.
Primary instruction cache 8kb, linesize 16 bytes (2 ways)
Primary data cache 4kb, linesize 16 bytes (2 ways)
Linux version 2.4.20 (root@omnibook) (gcc version 3.2.3 with Broadcom modifications) #9 Thu May 26 23:29:45 MSD 2005
Setting the PFC value as 0x15
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd init=/linuxrc console=ttyS0,115200
CPU: BCM4710 rev 0 at 125 MHz
!unable to setup serial console!
Calibrating delay loop... 82.94 BogoMIPS
Memory: 13868k/16384k available (1767k kernel code, 2516k reserved, 248k data, 72k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
NTFS driver v1.1.22 [Flags: R/O]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Flash device: 0x400000 at 0x1fc00000
Physically mapped flash: squashfs filesystem found at block 942
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x003e0000 : "linux"
0x000eba00-0x003e0000 : "rootfs"
0x003f0000-0x00400000 : "nvram"
0x003e0000-0x003f0000 : "config"
sflash: chipcommon not found
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 344 bytes per conntrack
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
FAT: bogus logical sector size 13056
FAT: bogus logical sector size 13056
NTFS: Unable to set blocksize 512.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 72k freed
Warning: unable to open an initial console.
Algorithmics/MIPS FPU Emulator v1.5
eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.7.0
eth1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.7.0
PCI: Enabling device 01:02.0 (0004 -> 0006)
eth2: Broadcom BCM4301 802.11 Wireless Controller 3.90.23.0
device eth0 entered promiscuous mode
device eth2 entered promiscuous mode
br0: port 2(eth2) entering listening state
br0: port 1(eth0) entering listening state
br0: port 2(eth2) entering learning state
br0: port 1(eth0) entering learning state
br0: port 2(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
usb-ohci.c: usb-00:04.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: new USB device 00:04.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x4e8/0x100) is not claimed by any active driver.
lp0: using parport0 (polling).
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
usb.c: registered new driver audio
audio.c: v1.0.0:USB Audio Class driver
Linux video capture interface: v1.00
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Model: USB DRIVE Rev: 1.12
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 125952 512-byte hdwr sectors (64 MB)
sda: Write Protect is off
Partition check:
/dev/scsi/host0/bus0/target0/lun0:<6>usb.c: USB disconnect on device 00:04.0-1 address 2
eth0: no IPv6 routers present
eth2: no IPv6 routers present
br0: no IPv6 routers present
hub.c: Cannot enable port 1 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
usb_control/bulk_msg: timeout
today i have buy a new usb stick from a-data, but i have a same problem whit a kingston stick
[admin@ (none) root] df
Filesystem 1k-bloks Used Available Use% Mounted on
/dev/root 3008 3008 0 100% /
[admin@ (none) root]
[admin@ (none) root] $ ls -l /dev/discs/disc0/
ls: /dev/discs/disc0/: No such file or directory
[admin@ (none) root]
only i have probleme with usb device
I see no reason for this. Perhaps your USB ports are damaged...
i think no, while when i put the transcend stick, the system recognize it, but does not contain partition table
to oleg - i have 500b not 500g
i press eject button in -> usb application->ftp server
an all works fine
thx for all replies
i set my asus lan address to 192.x.x.19
how can i set gateway for lan to 192.x.x.1
dns1 x.x.x.x
dns2 y.y.y.y
is this possible?
stil no 1.9.2.7.6c version when will it be functional?
Yeager, please use the edit button instead of create a new post for every little bit of info. Thanks.
i have search inthis forum, in google but cannot find the answer
I try (from my linux server) get snmp info on my Asus WL-500b,
(with firmware WL500b-1.9.2.7-6b.trx) but It seems doesnt working.
I try
/usr/local/mrtg-2/bin/cfgmaker public@80.250.xx.xx
but I got:::
SNMP Error:
no response received
I try too:
snmpwalk -v1 -c public 80.250.xx.xx
I got:
Timeout: No Response from 80.250.xx.xx
1, Of course I have Enable SNMP.. on YES, community name I for the first test I have public.
2, Of course from my linux sever I do a lots of walks to another routers like cisco, dlink.
Any Ideas what could be wrong ?
btw. thank you very much for this great job!
Are you trying to access this from WAN? If so, then this would not work until you adjust your firewall (manually vis post-firewall). This is a security feature.Quote:
Originally Posted by petek
Sorry, problem with SNMP solved. I just talk with my provider, from provider side are some rules for filtering snmp, and icmp. :-(
I have second questions about firewall.
I was searching for info about "howto write my own rules to firewall" which stay written after router reboot,
but I did not find it. Could You help. Me ?
Where and How write new rules permanently to firewall from shell ????
Thank You Petek.