Hytekk
13-05-2007, 00:55
Just when i should try and upload a firmware to the router the power came offline for a minute and now im stuck and cant get access to the router.
I then found this page: http://www.tiedyedfreaks.org/eric/WL-700gE/ and I have tried to install a USB-serial port to my ASUS WL-700gE with little or no success. I have modified a USB-cable (4 pin USB-A) so that i can connect one end to my computer and the other end im modifying to fit to the pin2, 3 and 4 on the board (TX, RX,GND). After that i connected it to my computer and powered on the router i get this error running dmesg:
[ 1465.572000] usb 1-2.3.1: new full speed USB device using uhci_hcd and address 48
[ 1465.708000] usb 1-2.3.1: configuration #1 chosen from 1 choice
[ 1465.912000] usb 1-2.3.2: new full speed USB device using uhci_hcd and address 49
[ 1466.028000] usb 1-2.3.2: configuration #1 chosen from 1 choice
[ 1466.604000] usb 4-1: new full speed USB device using uhci_hcd and address 5
[ 1466.728000] usb 4-1: device descriptor read/64, error -71
[ 1466.952000] usb 4-1: device descriptor read/64, error -71
[ 1467.168000] usb 4-1: new full speed USB device using uhci_hcd and address 6
[ 1467.292000] usb 4-1: device descriptor read/64, error -71
[ 1468.872000] usb 4-1: new full speed USB device using uhci_hcd and address 7
[ 1470.856000] hub 5-0:1.0: connect-debounce failed, port 7 disabled
[ 1472.784000] hub 5-0:1.0: connect-debounce failed, port 7 disabled
[ 1474.800000] hub 5-0:1.0: connect-debounce failed, port 7 disabled
What have i made wrong?
Could someone please help me out since there is no other way for me solve this problem (at least not that I know of).
The problem Im facing, after my power failure, is the ethernet-interface going up and down (both the LAN and WAN-port), it seems i cant keep a networkconnection to the router in more than a few seconds, cant ping the router or get an ip from it.
So it seems as if the router is in some sort of mid-boot-kernel-panic or something like that (the CFE-bootloader portion of the firmware is messed up?). I cant just make out this problem, that is why i really need to get the serialconsole up and running. This also means i cant use tftp to put a new firmware on the router.
I then found this page: http://www.tiedyedfreaks.org/eric/WL-700gE/ and I have tried to install a USB-serial port to my ASUS WL-700gE with little or no success. I have modified a USB-cable (4 pin USB-A) so that i can connect one end to my computer and the other end im modifying to fit to the pin2, 3 and 4 on the board (TX, RX,GND). After that i connected it to my computer and powered on the router i get this error running dmesg:
[ 1465.572000] usb 1-2.3.1: new full speed USB device using uhci_hcd and address 48
[ 1465.708000] usb 1-2.3.1: configuration #1 chosen from 1 choice
[ 1465.912000] usb 1-2.3.2: new full speed USB device using uhci_hcd and address 49
[ 1466.028000] usb 1-2.3.2: configuration #1 chosen from 1 choice
[ 1466.604000] usb 4-1: new full speed USB device using uhci_hcd and address 5
[ 1466.728000] usb 4-1: device descriptor read/64, error -71
[ 1466.952000] usb 4-1: device descriptor read/64, error -71
[ 1467.168000] usb 4-1: new full speed USB device using uhci_hcd and address 6
[ 1467.292000] usb 4-1: device descriptor read/64, error -71
[ 1468.872000] usb 4-1: new full speed USB device using uhci_hcd and address 7
[ 1470.856000] hub 5-0:1.0: connect-debounce failed, port 7 disabled
[ 1472.784000] hub 5-0:1.0: connect-debounce failed, port 7 disabled
[ 1474.800000] hub 5-0:1.0: connect-debounce failed, port 7 disabled
What have i made wrong?
Could someone please help me out since there is no other way for me solve this problem (at least not that I know of).
The problem Im facing, after my power failure, is the ethernet-interface going up and down (both the LAN and WAN-port), it seems i cant keep a networkconnection to the router in more than a few seconds, cant ping the router or get an ip from it.
So it seems as if the router is in some sort of mid-boot-kernel-panic or something like that (the CFE-bootloader portion of the firmware is messed up?). I cant just make out this problem, that is why i really need to get the serialconsole up and running. This also means i cant use tftp to put a new firmware on the router.