Bekijk de volledige versie : Oleg new 1.9.2.7-7g firmware
As I can see Oleg released the new 1.9.2.7-7g firmware (see relative post on russian forum). Can someone please translate that post in english too ?
Many thanks, Max
bamboocha
15-04-2007, 15:25
Hi QMax,
Changes:
1. New Busybox applets (env, cmp, wc, md5sum sha-1)
2. IGMP proxy added (multicast routing [IPTV]) (IP Config | Route > Enable multicast routing?)
3. Added an option to specify 802.11 multicast rate (Wireless | Advanced > Multicast rate)
4. New kernel features (incl. advanced router, new iptables targets)
5. Fixed compile problems with newer Linux ditributions
6. Web interface should no longer show Cable Disconnected status
7. There is now an option to enable/disable DoS protection (Internet Firewall | Basic Config > Enable DoS protection?)
8. Built-in ftp server should now work fine in PASV mode
9. Updated Dropbear to 0.49
10. Updated WiFi to 3.90.38.00
11. Added support for the 128MB of onboard RAM
12. hiddev support
13. FPU emulator fixes
14. WL-HDD IDE fixes - SMART should work now
15. Onboard flash type diagnostic messages
16. Fixed flashfs to respect comment signs
17. flash command now has progress indicator
18. Station/Ethernet Brodge mode should now associate faster to AP after reboot
19. WL500g Deluxe/Premium/WL550gE now rescpect WAN port settings from the web
20. WL500g Premium/WL550gE now better handles OFDM transmitter power setting
21. Added support for /etc/fstab before automount
22. Fixed problems then upgradinf via WiFi using WPA/WPA-PSK
23. Disabled "power off" for all units except WL-HDD
24. Pressing EZ SETUP button for 3 seconds would cause /usr/local/sbin/ez-setup to be executed
1.9.2.7-7g
Download: http://oleg.wl500g.info/1.9.2.7-7g/
hi
as I remember i had a similar problem before
i upload the new trx via the rooter's webpage, and it starts working.
in the ps processes there's a writing with big cpu usage maybe for a minute.
after the writing process finishes, init starts to work with maximum cpu usage and won't stop. i can't reboot, halt, anything.
after 15 minutes my patience flows away and i plug it out and in, and after this 'reboot' it shows firmware release is changed and everything goes fine.
why won't it reboot by itself?
additional comment:
actually not everything was fine, as I had to reload the flashs I saved previously on my HD. After that samba and every other things run.
If i install this firmware, will all my settings, be reseted ?
Ive got installed, Samba and sctcs
Sorry for the newbie :o
hi,
hopefully everything will stay as it was, but i strongly recommend doing setting and flashfs backups before every fw upgrade! (see my case)
i guess you know how to do that.
after loading back flashfs from the saved file, everything was just fine for me!
If i install this firmware, will all my settings, be reseted ?
Ive got installed, Samba and sctcs
Sorry for the newbie :o
Fox_Green
16-05-2007, 10:32
Hi,
i change to the new Oleg (before original Asus) firmware.
Is there any howto for using samba? I can't find my usb-storage with winXP.
Sorry for my english!
Fox
Is there any how to, or some manual for installing and using Oleg's firmware on wl-500gp router?
TNX!!!
Is there any how to, or some manual for installing and using Oleg's firmware on wl-500gp router?
TNX!!!
I intalled Oleg's firmware in the same way I upgraded my Asus with original firmware.
Access your router by a web browser (http://192.168.1.1 is the default address) then insert username/password (admin:admin by default).
Click on the left menu on System Setup and then Firmware Upgrade.
On the bottom box of this page, click on browse and point to the file you downloaded from Oleg's site http://oleg.wl500g.info/1.9.2.7-7g/WL500gp-1.9.2.7-7g.zip (YOU HAVE TO UNZIP IT FIRST !).
Click on Upload and... cross your finger... :D
Tutorial for optional modules can be found here: http://www.wl500g.info/showthread.php?t=5909
Good luck.
Max
Thank you for your answer.
I have some more questions about this Oleg's firmware :
1. Will I lose some features if I go to Oleg's firmware? If yes, what?
2. Is it easy to switch back to ASUS 1.9.7.0 firmware from Oleg's?
3. Does Oleg's firmware includes torrent client? Does it include all packages needed for normal work (all features presented in original firmware) or do I have to install them manually?
4. Does it have web interface, or it's command line only? If it has web interface can u manage everything within it?
5. Is there any chance to damage the router by using Oleg's firmware?
The features I need the most, are : good bandwidth management, download client (torrents and http), port forwarding and maybe wireless. Can I get this if I switch to Oleg's firmware, and will these services be more stable than using asus official firmware.
TNX!!!
The features I need the most, are : good bandwidth management, download client (torrents and http), port forwarding and maybe wireless. Can I get this if I switch to Oleg's firmware, and will these services be more stable than using asus official firmware.
TNX!!!
I'm satisfied with my swap to Oleg's, now I even can download torrents. Which I can't with the original firmware. Even faster than on my regular computer :) Once SCTCS gets some much needed improvements, I'll be even happier :)
Could it be possible to add a WOL (Wake up On Lan) functionality in future versions? :cool:
Hi QMax,
Changes:
1. New Busybox applets (env, cmp, wc, md5sum sha-1)
2. IGMP proxy added (multicast routing [IPTV]) (IP Config | Route > Enable multicast routing?)
3. Added an option to specify 802.11 multicast rate (Wireless | Advanced > Multicast rate)
4. New kernel features (incl. advanced router, new iptables targets)
5. Fixed compile problems with newer Linux ditributions
6. Web interface should no longer show Cable Disconnected status
7. There is now an option to enable/disable DoS protection (Internet Firewall | Basic Config > Enable DoS protection?)
8. Built-in ftp server should now work fine in PASV mode
9. Updated Dropbear to 0.49
10. Updated WiFi to 3.90.38.00
11. Added support for the 128MB of onboard RAM
12. hiddev support
13. FPU emulator fixes
14. WL-HDD IDE fixes - SMART should work now
15. Onboard flash type diagnostic messages
16. Fixed flashfs to respect comment signs
17. flash command now has progress indicator
18. Station/Ethernet Brodge mode should now associate faster to AP after reboot
19. WL500g Deluxe/Premium/WL550gE now rescpect WAN port settings from the web
20. WL500g Premium/WL550gE now better handles OFDM transmitter power setting
21. Added support for /etc/fstab before automount
22. Fixed problems then upgradinf via WiFi using WPA/WPA-PSK
23. Disabled "power off" for all units except WL-HDD
24. Pressing EZ SETUP button for 3 seconds would cause /usr/local/sbin/ez-setup to be executed
1.9.2.7-7g
Download: http://oleg.wl500g.info/1.9.2.7-7g/
I click on link? but nothing...
Please give me link like rapidhare ore other...
alien433
08-07-2007, 19:46
i test the link and the link is working
Link works for me too.
Max
Antiloop
09-07-2007, 00:15
I click on link? but nothing...
Please give me link like rapidhare ore other...
normally they can be obtained from http://files.wl500g.info which mirrors every firmware every came out from Oleg and Asus
a tech guy is attempting to repair the files.wl500g.info server tomorrow, maybe it will be up then
Hello Oleg - its possible include in future release your firmware this kernel module? Up to 300 new cameras might work.
Thanks
Hi everyone, I just recently bought the Asus Wl-500gP and I'm having some issues already, (mainly due to BT connections overloading the router) so I'm deciding whether or not to switch to third party firmware.
So far I have looked at dd-wrt, open-wrt and oleg. I can't really decide though. So can anyone tell me what functions I gain/lose if I install this firmware?
USB is a big functionality for me because i want to hook up my printer to it and an external hard drive in the future.
Thanks all and sorry for being a noob at this :p
Probably I did something wrong. I uploaded this version of fw. and the power LED started flashing (about every second). I wait for about 20 mins, than I restarted router. After restart LED is again blinking. Connection over LAN works, over Wi-Fi no. I´m not able reach web interface.
So, I´ve to use Fw.restoratin utiliy, but somwehere I found that I´ve to change IP of PC to 192.168.1.10 (but this IP I already used - for router, cause 192.168.1.1 is assigned to another one, doesn´t matter). So, why is necesary to have 192.168.1.10 assigned to PC?
I did flash just cause of WebCamera - I bought Logitech QuickCam Sphere and it doesn´t work for me with original fw. I hoped, it will work with Oleg´s
So:
1) Any idea what´s happedn during flash?
2) I´ve to use Restoraton utility? Or any anoither way?
3) will this webcam works with original fw., or with Olge´s , or it will not work?
thx 4 help