Firmware v9.8.1.9 BETA [Archive] - AsusForum.NET -- WL500g

Bekijk de volledige versie : Firmware v9.8.1.9 BETA

Antiloop

03-09-2004, 12:29

WARNING: BETA VERSION
TRY AT YOUR OWN RISK!

DO NOT UPGRADE UNLESS YOU KNOW WHAT YOU ARE DOING
DOWNGRADE IS NOT EASILY POSSIBLE!!

Changelog:

nothing known yet

WL500g_9.8.1.9_EN.zip (http://wl500g.dyndns.org/WL500g_9.8.1.9_EN.zip)
i do not know the differences, normally this should be the beta of firmware 1.8.1.9 allthough it's out already !? but this one came later

Oleg

03-09-2004, 16:59

Well, this seems to be 1.8.1.9 based build, but with debug information turned on in the et driver. I guess, this should aim in tracking down WAN port die problem. So, everyone with 1.8.1.9 and having WAN problem, which can be workaround by renewing DHCP lease should try to flash this firmware and check the system log. It should contain debug info (if it does not - probably Asus has forgotted something). You then should kill your WAN port and copy the system log BEFORE rebooting/renewing lease. Post it here. I will try to check for any hints on problem.
Also, just an idea - if it does not contain any debug info - try running

dmesg

via well known www backdoor.

Antiloop

05-09-2004, 03:10

about the QOS stuff:

found this in my nvram values:

qos_enable_x=0
qos_ipaddr_x=
qos_priority_x=
qos_maxbw_x=
qos_dir_x=
qos_minbw_x=
qos_port_x=
qos_rulenum_x=0

see also pic attached

Antiloop

05-09-2004, 04:53

Jan 1 00:00:01 klogd: CPU revision is: 00024000
Jan 1 00:00:01 klogd: Loading BCM4710 MMU routines.
Jan 1 00:00:01 klogd: Primary instruction cache 8kb, linesize 16 bytes (2 ways)
Jan 1 00:00:01 klogd: Primary data cache 4kb, linesize 16 bytes (2 ways)
Jan 1 00:00:01 klogd: Linux version 2.4.20 (root@localhost.localdomain) (gcc version 3.2.3 with Broadcom modifications) #124 Wed Sep 1 15:16:17 CST 2004
Jan 1 00:00:01 klogd: Determined physical RAM map:
Jan 1 00:00:01 klogd: memory: 01000000 @ 00000000 (usable)
Jan 1 00:00:01 klogd: On node 0 totalpages: 4096
Jan 1 00:00:01 klogd: zone(0): 4096 pages.
Jan 1 00:00:01 klogd: zone(1): 0 pages.
Jan 1 00:00:01 klogd: zone(2): 0 pages.
Jan 1 00:00:01 klogd: Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Jan 1 00:00:01 klogd: CPU: BCM4710 rev 0 at 125 MHz
Jan 1 00:00:01 klogd: !unable to setup serial console!
Jan 1 00:00:01 klogd: Calibrating delay loop... 82.94 BogoMIPS
Jan 1 00:00:01 klogd: Memory: 14228k/16384k available (1448k kernel code, 2156k reserved, 208k data, 64k init, 0k highmem)
Jan 1 00:00:01 klogd: Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Jan 1 00:00:01 klogd: Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Jan 1 00:00:01 klogd: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Jan 1 00:00:01 klogd: Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 00:00:01 klogd: Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 00:00:01 klogd: Checking for 'wait' instruction... unavailable.
Jan 1 00:00:01 klogd: POSIX conformance testing by UNIFIX
Jan 1 00:00:01 klogd: PCI: Fixing up bus 0
Jan 1 00:00:01 klogd: PCI: Fixing up bridge
Jan 1 00:00:01 klogd: PCI: Fixing up bus 1
Jan 1 00:00:01 klogd: Linux NET4.0 for Linux 2.4
Jan 1 00:00:01 klogd: Based upon Swansea University Computer Society NET3.039
Jan 1 00:00:01 klogd: Initializing RT netlink socket
Jan 1 00:00:01 klogd: Starting kswapd
Jan 1 00:00:01 klogd: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
Jan 1 00:00:01 klogd: devfs: boot_options: 0x1
Jan 1 00:00:01 klogd: NTFS driver v1.1.22 [Flags: R/O]
Jan 1 00:00:01 klogd: pty: 256 Unix98 ptys configured
Jan 1 00:00:01 klogd: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Jan 1 00:00:01 klogd: PPP generic driver version 2.4.2
Jan 1 00:00:01 klogd: PPP Deflate Compression module registered
Jan 1 00:00:01 klogd: PPP BSD Compression module registered
Jan 1 00:00:01 klogd: Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Jan 1 00:00:01 klogd: Physically mapped flash: Swapping erase regions for broken CFI table.
Jan 1 00:00:01 klogd: number of CFI chips: 1
Jan 1 00:00:01 klogd: Flash device: 0x400000 at 0x1fc00000
Jan 1 00:00:01 klogd: Physically mapped flash: cramfs filesystem found at block 1027
Jan 1 00:00:01 klogd: Creating 4 MTD partitions on "Physically mapped flash":
Jan 1 00:00:01 klogd: 0x00000000-0x00040000 : "pmon"
Jan 1 00:00:01 klogd: 0x00040000-0x003f0000 : "linux"
Jan 1 00:00:01 klogd: 0x00100f5c-0x003f0000 : "rootfs"
Jan 1 00:00:01 klogd: 0x003f0000-0x00400000 : "nvram"
Jan 1 00:00:01 klogd: sflash: chipcommon not found
Jan 1 00:00:01 klogd: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 1 00:00:01 klogd: IP Protocols: ICMP, UDP, TCP
Jan 1 00:00:01 klogd: IP: routing cache hash table of 512 buckets, 4Kbytes
Jan 1 00:00:01 klogd: TCP: Hash tables configured (established 1024 bind 2048)
Jan 1 00:00:01 klogd: ip_conntrack version 2.1 (128 buckets, 1024 max) - 344 bytes per conntrack
Jan 1 00:00:01 klogd: ip_conntrack_pptp.c:init: ip_conntrack_pptp.c: registering helper
Jan 1 00:00:01 klogd: ip_conntrack_pptp version 1.9 loaded
Jan 1 00:00:01 klogd: ip_nat_pptp version 1.5 loaded
Jan 1 00:00:01 klogd: ip_tables: (C) 2000-2002 Netfilter core team
Jan 1 00:00:01 klogd: ipt_time loading
Jan 1 00:00:01 klogd: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Jan 1 00:00:01 klogd: NET4: Ethernet Bridge 008 for NET4.0
Jan 1 00:00:01 klogd: 802.1Q VLAN Support v1.7 Ben Greear reearb@candelatech.com>
Jan 1 00:00:01 klogd: All bugs added by David S. Miller avem@redhat.com>
Jan 1 00:00:01 klogd: VFS: Mounted root (cramfs filesystem) readonly.
Jan 1 00:00:01 klogd: Mounted devfs on /dev
Jan 1 00:00:01 klogd: Freeing unused kernel memory: 64k freed
Jan 1 00:00:01 klogd: Warning: unable to open an initial console.
Jan 1 00:00:01 klogd: eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 1.3.2.0
Jan 1 00:00:01 klogd: eth1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 1.3.2.0
Jan 1 00:00:01 klogd: robosw_attach_ocp: no Robo device on OCP bus
Jan 1 00:00:01 klogd: robosw_attach_pmii: no Robo switch detected
Jan 1 00:00:01 klogd: Robo switch init failed
Jan 1 00:00:01 klogd: unregister_netdevice: device eth2/802f7800 never was registered
Jan 1 00:00:01 klogd: PCI: Enabling device 01:02.0 (0004 -> 0006)
Jan 1 00:00:01 klogd: eth2: Broadcom BCM4320 802.11 Wireless Controller 1.3.2.0
Jan 1 00:00:01 klogd: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 00:00:01 klogd: device eth0 entered promiscuous mode
Jan 1 00:00:01 klogd: device eth2 entered promiscuous mode
Jan 1 00:00:01 klogd: br0: port 2(eth2) entering listening state
Jan 1 00:00:01 klogd: br0: port 1(eth0) entering listening state
Jan 1 00:00:01 klogd: br0: port 2(eth2) entering learning state
Jan 1 00:00:01 klogd: br0: port 1(eth0) entering learning state
Jan 1 00:00:01 klogd: br0: port 2(eth2) entering forwarding state
Jan 1 00:00:01 klogd: br0: topology change detected, propagating
Jan 1 00:00:01 klogd: br0: port 1(eth0) entering forwarding state
Jan 1 00:00:01 klogd: br0: topology change detected, propagating
Jan 1 00:00:01 klogd: usb.c: registered new driver usbdevfs
Jan 1 00:00:01 klogd: usb.c: registered new driver hub
Jan 1 00:00:02 klogd: usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
Jan 1 00:00:02 klogd: usb-ohci.c: usb-00:04.0, PCI device 14e4:4715
Jan 1 00:00:02 klogd: usb.c: new USB bus registered, assigned bus number 1
Jan 1 00:00:02 klogd: hub.c: USB hub found
Jan 1 00:00:02 klogd: hub.c: 2 ports detected
Jan 1 00:00:02 klogd: uhci.c: USB Universal Host Controller Interface driver v1.1
Jan 1 00:00:02 klogd: lp0: using parport0 (polling).

------CUT------
download attachment for full systemlog

Oleg

05-09-2004, 08:26

Well, that's the relevant part -

Sep 5 01:13:20 klogd: A1 1 1 0 1

Sep 5 01:13:21 klogd: A1 1 1 0 2

Sep 5 01:13:24 klogd: A1 1 1 0 1

Sep 5 01:13:25 klogd: A1 1 1 0 2

Sep 5 01:13:26 klogd: A1 1 2 0 3

Sep 5 01:13:26 ntp client: time is synchronized to time.nist.gov

Sep 5 01:13:32 klogd: A1 1 1 0 1

Sep 5 01:13:33 klogd: A1 1 1 0 2

Sep 5 01:13:34 klogd: A1 1 2 0 3

Sep 5 01:13:35 klogd: A1 1 2 0 4

Sep 5 01:13:35 klogd: EEEE: RESET

Sep 5 01:13:46 klogd: A1 1 6 0 1

Sep 5 01:13:47 klogd: A1 1 17 0 2

Sep 5 01:13:48 klogd: A1 1 18 0 3

Sep 5 01:13:49 klogd: A1 1 18 0 4

Sep 5 01:13:49 klogd: EEEE: RESET

Sep 5 01:14:02 klogd: A1 1 1 0 1

Sep 5 01:14:03 klogd: A1 1 1 0 2

Sep 5 01:14:04 klogd: A1 1 2 0 3

Sep 5 01:14:05 klogd: A1 1 2 0 4

Sep 5 01:14:05 klogd: EEEE: RESET

Sep 5 01:14:16 klogd: A1 1 17 0 1

Sep 5 01:14:17 klogd: A1 1 17 0 2

Sep 5 01:14:18 klogd: A1 1 18 0 3

Sep 5 01:14:19 klogd: A1 1 18 0 4

Sep 5 01:14:19 klogd: EEEE: RESET

Sep 5 01:14:30 klogd: A1 1 17 0 1

Sep 5 01:14:31 klogd: A1 1 17 0 2

This is something added by ASUS, but incomplete...
Try running this line

et -i eth1 msglevel 15

This should not produce output, but should enable debug messages on. Also, have you tried dmesg?

shopping

06-09-2004, 17:14

http://192.168.1.1/Advanced_QOS_Content.asp

QoS web setting is also avalible at official version 1.8.1.9.

but the whatever setting, no useful at all.
my download or upload speed still can reach the maximum.

how to use that?
will ASUS fix that and release the new firmware include that?

Antiloop

06-09-2004, 19:02