Bekijk de volledige versie : 700gE Printserver vs HP OfficeJet G85
Hi People,
i'm at the end of my knowledge. I'm not a linux guru. :(
I connect the HP OfficeJet G85 to the wl700ge, on the printer config page is writen:
Connected Printers:
Printer Manufacturer Model Serial
OfficeJet-G851 Hewlett-Packard OfficeJet-G851 XXXXXXXXXXXX
So the printer is accepted (i think).
After i create a new printer in winxp as described, and try the test page. And nothing happens. After a minute or two i receive the xp-bubble saying the document can not be printed.
Anybody please HELP!!!:eek:
thanx
peterke
gratitude182
01-02-2007, 06:47
maybe you need a alternative driver from hp (which is also usable for this printer) in windows xp to print over network...
this is the case with my hp-psc 1315 because the driver from hp 1315 isn't a network driver.
grat182
enrico99
01-02-2007, 09:28
Hello!
I am new in this forum. I have the same problems with the G85. Can you tell me which driver you installed instead of the origianel G85 driver?
Thank you!!
Thanx for reply Dudes!:cool:
I'll try the HP drivers, good chance! The drivers i set up? I don't know. It was the default winxp sp2 driver (i think). I just picked it from the list. If wanna see vendor and version, i can tell you tonight (at home, 'couse i'm at work now).
best regards,
peterke
Hey Guys,
no success with the hp original drivers. :mad:
Still the same situation: printer detected by the 700ge, but can't print. if i try to set up the printer double-clicking the shared link under the 700ge's shares, after the installation the printer has no port selected, and if i press countinue printing, it responds access denied. :confused:
PLEASE HELP!!! ANYBODY!!!
thanx
peterke
Hi Friends,
everytime i try to print, i get this 2 lines added to the system log:
Feb 1 23:28:44 printd[22363]: Startup
Feb 1 23:28:44 printd[22363]: bind: Address already in use
Does this have a meaning?
Best Regards,
peterke
Feb 1 23:28:44 printd[22363]: Startup
Feb 1 23:28:44 printd[22363]: bind: Address already in use
Does this have a meaning?
No. It'll happen every time you view the status page. Opening the page causes the router to try to re-run printd. Since printd is already running, any further instances won't run because the network port it uses is already being used by the first instance.
I see this all the time and printing works OK for me using a generic USB to parallel cable.
- K.C.
gratitude182
02-02-2007, 08:36
try to install g95 driver... maybe that helps...
or google to find maybe a solution
grat182
Hi again!
Now i'm tricking. After i unpluged the printer from the router, and pluged into the notebook directly, i was unable to print. After i powered down the printer, and pluged back the power supply, the print was ok.
After i restarted the router and connected the printer again, the printing was impossible again. But since that i see the following 2 lines repeating every 2 minutes:
Feb 2 18:55:49 printd[903]: Startup
Feb 2 18:55:49 printd[903]: bind: Address already in use
Feb 2 18:57:34 printd[938]: Startup
Feb 2 18:57:34 printd[938]: bind: Address already in use
Feb 2 18:59:19 printd[973]: Startup
Feb 2 18:59:19 printd[973]: bind: Address already in use
Feb 2 19:01:04 printd[1008]: Startup
Feb 2 19:01:04 printd[1008]: bind: Address already in use
Feb 2 19:02:49 printd[1043]: Startup
Feb 2 19:02:49 printd[1043]: bind: Address already in use
Feb 2 19:04:34 printd[1078]: Startup
Feb 2 19:04:34 printd[1078]: bind: Address already in use
Feb 2 19:05:13 -- MARK --
Feb 2 19:06:19 printd[1113]: Startup
Feb 2 19:06:19 printd[1113]: bind: Address already in use
Do anybody have a good idea?
Now i try the g95 driver.
I'll be back! :D
best regards,
peterke
Hi Friends,
i'm out of knowledge! :(
With g95 driver can't help.
That the 2 lines described above are repeating periodically, tells me, that the router gets the job, the spool works, but can't put it to the printer 'couse the driver in the linux can't connect to the printer.
is it possible to extend the linux with a driver mathcing to my printer?
thanx again!
peterke
Hi Friends,
the asus's printer compatibility site is now updated:
G85 is supported only via paralell port!
What?
Where can i find the paralell port on the 700gE? :D
What you think guys, an usb2lpt adapter would help me?
many thanx
peterke
What you think guys, an usb2lpt adapter would help me?
Yes. My generic adapter works perfectly.
- K.C.
Hmmm. I connected the G85 now via usb2lpt adapter. And it S*CKS!
The above writen 2 lines ar repeating continously and nothing happens! :(
Any ideas?
Or shell i replace the good old printer?
thanx
peterke