TinyRK
17-01-2006, 15:18
Hi there,
my problem is, that after a while my WLan-Card loses the connection to my WL-500g Dlx.
When I search for it with NetStumbler there is no SSID found.
The LogFile of my WL-500g Dlx:
Jan 1 01:00:04 syslogd started: BusyBox v1.00 (2005.05.11-18:29+0000)
Jan 1 01:00:04 kernel: FAT: bogus logical sector size 45056
Jan 1 01:00:04 kernel: NTFS: Unable to set blocksize 512.
Jan 1 01:00:04 kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 01:00:04 kernel: Mounted devfs on /dev
Jan 1 01:00:04 kernel: Freeing unused kernel memory: 72k freed
Jan 1 01:00:04 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 01:00:04 kernel: eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.7.0
Jan 1 01:00:04 kernel: PCI: Enabling device 01:03.0 (0004 -> 0006)
Jan 1 01:00:04 kernel: ontroller 3.90.23.0
Jan 1 01:00:04 kernel: vlan0: add xx:xx:xx:xx mcast address to master interface
Jan 1 01:00:04 kernel: vlan0: add xx:xx:xx:xx mcast address to master interface
Jan 1 01:00:04 kernel: vlan0: dev_set_promiscuity(master, 1)
Jan 1 01:00:04 kernel: device eth0 entered promiscuous mode
Jan 1 01:00:04 kernel: device vlan0 entered promiscuous mode
Jan 1 01:00:04 kernel: device eth1 entered promiscuous mode
Jan 1 01:00:04 kernel: br0: port 2(eth1) entering listening state
Jan 1 01:00:04 kernel: br0: port 1(vlan0) entering listening state
Jan 1 01:00:04 kernel: br0: port 2(eth1) entering learning state
Jan 1 01:00:04 kernel: br0: port 1(vlan0) entering learning state
Jan 1 01:00:04 kernel: br0: port 2(eth1) entering forwarding state
Jan 1 01:00:04 kernel: br0: topology change detected, propagating
Jan 1 01:00:04 kernel: br0: port 1(vlan0) entering forwarding state
Jan 1 01:00:04 kernel: br0: topology change detected, propagating
Jan 1 01:00:05 kernel: usb.c: registered new driver usbdevfs
Jan 1 01:00:05 kernel: usb.c: registered new driver hub
Jan 1 01:00:05 kernel: usb-uhci.c: $Revision: 1.275 $ time 21:43:09 Apr 20 2005
Jan 1 01:00:05 kernel: usb-uhci.c: High bandwidth mode enabled
Jan 1 01:00:05 kernel: PCI: Enabling device 01:02.0 (0000 -> 0001)
Jan 1 01:00:05 kernel: usb-uhci.c: USB UHCI at I/O 0x100, IRQ 2
Jan 1 01:00:05 kernel: usb-uhci.c: Detected 2 ports
Jan 1 01:00:05 kernel: usb.c: new USB bus registered, assigned bus number 1
Jan 1 01:00:05 kernel: hub.c: USB hub found
Jan 1 01:00:05 kernel: hub.c: 2 ports detected
Jan 1 01:00:05 kernel: PCI: Enabling device 01:02.1 (0000 -> 0001)
Jan 1 01:00:05 kernel: usb-uhci.c: USB UHCI at I/O 0x120, IRQ 2
Jan 1 01:00:05 kernel: usb-uhci.c: Detected 2 ports
Jan 1 01:00:05 kernel: usb.c: new USB bus registered, assigned bus number 2
Jan 1 01:00:05 kernel: hub.c: USB hub found
Jan 1 01:00:05 kernel: hub.c: 2 ports detected
Jan 1 01:00:05 kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Jan 1 01:00:06 kernel: PCI: Enabling device 01:02.2 (0000 -> 0002)
Jan 1 01:00:06 kernel: ehci_hcd 01:02.2: PCI device 1106:3104
Jan 1 01:00:06 kernel: ehci_hcd 01:02.2: irq 2, pci mem c00a2000
Jan 1 01:00:06 kernel: usb.c: new USB bus registered, assigned bus number 3
Jan 1 01:00:06 kernel: PCI: 01:02.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32
Jan 1 01:00:06 kernel: ehci_hcd 01:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
Jan 1 01:00:06 kernel: hub.c: USB hub found
Jan 1 01:00:06 kernel: hub.c: 4 ports detected
Jan 1 01:00:06 kernel: usb.c: registered new driver usblp
Jan 1 01:00:06 kernel: printer.c: v0.13: USB Printer Device Class driver
Jan 1 01:00:08 kernel: usb.c: registered new driver audio
Jan 1 01:00:08 kernel: audio.c: v1.0.0:USB Audio Class driver
Jan 1 01:00:08 kernel: Linux video capture interface: v1.00
Jan 1 01:00:08 kernel: SCSI subsystem driver Revision: 1.00
Jan 1 01:00:09 kernel: Initializing USB Mass Storage driver...
Jan 1 01:00:09 kernel: usb.c: registered new driver usb-storage
Jan 1 01:00:09 kernel: USB Mass Storage support registered.
Jan 1 01:00:09 kernel: vlan1: Setting MAC address to 00 11 d8 xx xx xx.
Jan 1 01:00:09 kernel: VLAN (vlan1): Underlying device (eth0) has same MAC, not checking promiscious mode.
Jan 1 01:00:09 kernel: vlan1: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:00:09 kernel: vlan1: add 33:33:xx:xx:xx:xxmcast address to master interface
Jan 1 01:00:09 pppd[92]: Plugin rp-pppoe.so loaded.
Jan 1 01:00:09 pppd[92]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
Jan 1 01:00:09 pppd[93]: pppd 2.4.2 started by TinyRK, uid 0
Jan 1 01:00:09 radvd[94]: version 0.7.2 started
Jan 1 01:00:09 radvd[94]: prefix length should be 64 for br0
Jan 1 01:00:10 pppd[93]: PPP session is 1347
Jan 1 01:00:10 pppd[93]: Using interface ppp0
Jan 1 01:00:10 pppd[93]: Connect: ppp0 <--> vlan1
Jan 1 01:00:10 pppd[93]: PAP authentication succeeded
Jan 1 01:00:10 pppd[93]: peer from calling number 00:xx:xx:xx:xx:xx authorized
Jan 1 01:00:10 pppd[93]: local IP address xx:xx:xx:xx
Jan 1 01:00:10 pppd[93]: remote IP address xx:xx:xx:xx
Jan 1 01:00:10 pppd[93]: primary DNS address xx.xx.xx.xx
Jan 1 01:00:10 pppd[93]: secondary DNS address xx.xx.xx.xx
Jan 1 01:00:11 dnsmasq[69]: read /etc/hosts - 4 addresses
Jan 1 01:00:11 dnsmasq[69]: read /etc/ethers - 3 addresses
Jan 1 01:00:11 dnsmasq[69]: reading /tmp/resolv.conf
Jan 1 01:00:11 dnsmasq[69]: using nameserver
Jan 1 01:00:11 dnsmasq[69]: using nameserver
Jan 1 01:00:11 PPPoE: connect to ISP
Jan 17 11:13:08 ntp client: Synchronizing time with time.nist.gov ...
Jan 17 11:13:50 dnsmasq[69]: DHCPDISCOVER(br0) xx:xxxx:xx:xx:xx
Jan 17 11:13:50 dnsmasq[69]: DHCPOFFER(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 11:13:50 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 11:13:50 dnsmasq[69]: DHCPACK(br0) 192.168.1.2 xx:xx:xx:xx:xx:xxdesktop
Jan 17 13:13:08 ntp client: Synchronizing time with time.nist.gov ...
Jan 17 13:13:50 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.10 0xx:xx:xx:xx
Jan 17 13:13:50 dnsmasq[69]: DHCPACK(br0) 192.168.1.10 xx:xx:xx:xx:ss:ss papa
Jan 17 13:51:03 dnsmasq[69]: DHCPDISCOVER(br0) xx:xx:xx:xx
Jan 17 13:51:03 dnsmasq[69]: DHCPOFFER(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 13:51:03 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 13:51:03 dnsmasq[69]: DHCPACK(br0) 192.168.1.2 xx:xx:xx:xx:ss:ssdesktop
Jan 17 14:08:12 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 14:08:12 dnsmasq[69]: DHCPACK(br0) 192.168.1.2 xx:xx:xx:xxdesktop
Jan 17 15:13:13 ntp client: Synchronizing time with time.nist.gov ...
Jan 17 16:02:38 dnsmasq[69]: DHCPDISCOVER(br0) xx:xx:xx:xx
Jan 17 16:02:38 dnsmasq[69]: DHCPOFFER(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 16:02:38 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 16:02:38 dnsmasq[69]: DHCPACK(br0) 192.168.1.2 xx:xx:xx:xx
desktop
Any ideas?
I do use WPA -AES with a Belkin F5D7001 without Afterbuner.
Serveral channels were tried: no changes.
Is Bittorrent the problem?
Thanks in advance :)
my problem is, that after a while my WLan-Card loses the connection to my WL-500g Dlx.
When I search for it with NetStumbler there is no SSID found.
The LogFile of my WL-500g Dlx:
Jan 1 01:00:04 syslogd started: BusyBox v1.00 (2005.05.11-18:29+0000)
Jan 1 01:00:04 kernel: FAT: bogus logical sector size 45056
Jan 1 01:00:04 kernel: NTFS: Unable to set blocksize 512.
Jan 1 01:00:04 kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 01:00:04 kernel: Mounted devfs on /dev
Jan 1 01:00:04 kernel: Freeing unused kernel memory: 72k freed
Jan 1 01:00:04 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 01:00:04 kernel: eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.7.0
Jan 1 01:00:04 kernel: PCI: Enabling device 01:03.0 (0004 -> 0006)
Jan 1 01:00:04 kernel: ontroller 3.90.23.0
Jan 1 01:00:04 kernel: vlan0: add xx:xx:xx:xx mcast address to master interface
Jan 1 01:00:04 kernel: vlan0: add xx:xx:xx:xx mcast address to master interface
Jan 1 01:00:04 kernel: vlan0: dev_set_promiscuity(master, 1)
Jan 1 01:00:04 kernel: device eth0 entered promiscuous mode
Jan 1 01:00:04 kernel: device vlan0 entered promiscuous mode
Jan 1 01:00:04 kernel: device eth1 entered promiscuous mode
Jan 1 01:00:04 kernel: br0: port 2(eth1) entering listening state
Jan 1 01:00:04 kernel: br0: port 1(vlan0) entering listening state
Jan 1 01:00:04 kernel: br0: port 2(eth1) entering learning state
Jan 1 01:00:04 kernel: br0: port 1(vlan0) entering learning state
Jan 1 01:00:04 kernel: br0: port 2(eth1) entering forwarding state
Jan 1 01:00:04 kernel: br0: topology change detected, propagating
Jan 1 01:00:04 kernel: br0: port 1(vlan0) entering forwarding state
Jan 1 01:00:04 kernel: br0: topology change detected, propagating
Jan 1 01:00:05 kernel: usb.c: registered new driver usbdevfs
Jan 1 01:00:05 kernel: usb.c: registered new driver hub
Jan 1 01:00:05 kernel: usb-uhci.c: $Revision: 1.275 $ time 21:43:09 Apr 20 2005
Jan 1 01:00:05 kernel: usb-uhci.c: High bandwidth mode enabled
Jan 1 01:00:05 kernel: PCI: Enabling device 01:02.0 (0000 -> 0001)
Jan 1 01:00:05 kernel: usb-uhci.c: USB UHCI at I/O 0x100, IRQ 2
Jan 1 01:00:05 kernel: usb-uhci.c: Detected 2 ports
Jan 1 01:00:05 kernel: usb.c: new USB bus registered, assigned bus number 1
Jan 1 01:00:05 kernel: hub.c: USB hub found
Jan 1 01:00:05 kernel: hub.c: 2 ports detected
Jan 1 01:00:05 kernel: PCI: Enabling device 01:02.1 (0000 -> 0001)
Jan 1 01:00:05 kernel: usb-uhci.c: USB UHCI at I/O 0x120, IRQ 2
Jan 1 01:00:05 kernel: usb-uhci.c: Detected 2 ports
Jan 1 01:00:05 kernel: usb.c: new USB bus registered, assigned bus number 2
Jan 1 01:00:05 kernel: hub.c: USB hub found
Jan 1 01:00:05 kernel: hub.c: 2 ports detected
Jan 1 01:00:05 kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Jan 1 01:00:06 kernel: PCI: Enabling device 01:02.2 (0000 -> 0002)
Jan 1 01:00:06 kernel: ehci_hcd 01:02.2: PCI device 1106:3104
Jan 1 01:00:06 kernel: ehci_hcd 01:02.2: irq 2, pci mem c00a2000
Jan 1 01:00:06 kernel: usb.c: new USB bus registered, assigned bus number 3
Jan 1 01:00:06 kernel: PCI: 01:02.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32
Jan 1 01:00:06 kernel: ehci_hcd 01:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
Jan 1 01:00:06 kernel: hub.c: USB hub found
Jan 1 01:00:06 kernel: hub.c: 4 ports detected
Jan 1 01:00:06 kernel: usb.c: registered new driver usblp
Jan 1 01:00:06 kernel: printer.c: v0.13: USB Printer Device Class driver
Jan 1 01:00:08 kernel: usb.c: registered new driver audio
Jan 1 01:00:08 kernel: audio.c: v1.0.0:USB Audio Class driver
Jan 1 01:00:08 kernel: Linux video capture interface: v1.00
Jan 1 01:00:08 kernel: SCSI subsystem driver Revision: 1.00
Jan 1 01:00:09 kernel: Initializing USB Mass Storage driver...
Jan 1 01:00:09 kernel: usb.c: registered new driver usb-storage
Jan 1 01:00:09 kernel: USB Mass Storage support registered.
Jan 1 01:00:09 kernel: vlan1: Setting MAC address to 00 11 d8 xx xx xx.
Jan 1 01:00:09 kernel: VLAN (vlan1): Underlying device (eth0) has same MAC, not checking promiscious mode.
Jan 1 01:00:09 kernel: vlan1: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:00:09 kernel: vlan1: add 33:33:xx:xx:xx:xxmcast address to master interface
Jan 1 01:00:09 pppd[92]: Plugin rp-pppoe.so loaded.
Jan 1 01:00:09 pppd[92]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
Jan 1 01:00:09 pppd[93]: pppd 2.4.2 started by TinyRK, uid 0
Jan 1 01:00:09 radvd[94]: version 0.7.2 started
Jan 1 01:00:09 radvd[94]: prefix length should be 64 for br0
Jan 1 01:00:10 pppd[93]: PPP session is 1347
Jan 1 01:00:10 pppd[93]: Using interface ppp0
Jan 1 01:00:10 pppd[93]: Connect: ppp0 <--> vlan1
Jan 1 01:00:10 pppd[93]: PAP authentication succeeded
Jan 1 01:00:10 pppd[93]: peer from calling number 00:xx:xx:xx:xx:xx authorized
Jan 1 01:00:10 pppd[93]: local IP address xx:xx:xx:xx
Jan 1 01:00:10 pppd[93]: remote IP address xx:xx:xx:xx
Jan 1 01:00:10 pppd[93]: primary DNS address xx.xx.xx.xx
Jan 1 01:00:10 pppd[93]: secondary DNS address xx.xx.xx.xx
Jan 1 01:00:11 dnsmasq[69]: read /etc/hosts - 4 addresses
Jan 1 01:00:11 dnsmasq[69]: read /etc/ethers - 3 addresses
Jan 1 01:00:11 dnsmasq[69]: reading /tmp/resolv.conf
Jan 1 01:00:11 dnsmasq[69]: using nameserver
Jan 1 01:00:11 dnsmasq[69]: using nameserver
Jan 1 01:00:11 PPPoE: connect to ISP
Jan 17 11:13:08 ntp client: Synchronizing time with time.nist.gov ...
Jan 17 11:13:50 dnsmasq[69]: DHCPDISCOVER(br0) xx:xxxx:xx:xx:xx
Jan 17 11:13:50 dnsmasq[69]: DHCPOFFER(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 11:13:50 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 11:13:50 dnsmasq[69]: DHCPACK(br0) 192.168.1.2 xx:xx:xx:xx:xx:xxdesktop
Jan 17 13:13:08 ntp client: Synchronizing time with time.nist.gov ...
Jan 17 13:13:50 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.10 0xx:xx:xx:xx
Jan 17 13:13:50 dnsmasq[69]: DHCPACK(br0) 192.168.1.10 xx:xx:xx:xx:ss:ss papa
Jan 17 13:51:03 dnsmasq[69]: DHCPDISCOVER(br0) xx:xx:xx:xx
Jan 17 13:51:03 dnsmasq[69]: DHCPOFFER(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 13:51:03 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 13:51:03 dnsmasq[69]: DHCPACK(br0) 192.168.1.2 xx:xx:xx:xx:ss:ssdesktop
Jan 17 14:08:12 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 14:08:12 dnsmasq[69]: DHCPACK(br0) 192.168.1.2 xx:xx:xx:xxdesktop
Jan 17 15:13:13 ntp client: Synchronizing time with time.nist.gov ...
Jan 17 16:02:38 dnsmasq[69]: DHCPDISCOVER(br0) xx:xx:xx:xx
Jan 17 16:02:38 dnsmasq[69]: DHCPOFFER(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 16:02:38 dnsmasq[69]: DHCPREQUEST(br0) 192.168.1.2 xx:xx:xx:xx
Jan 17 16:02:38 dnsmasq[69]: DHCPACK(br0) 192.168.1.2 xx:xx:xx:xx
desktop
Any ideas?
I do use WPA -AES with a Belkin F5D7001 without Afterbuner.
Serveral channels were tried: no changes.
Is Bittorrent the problem?
Thanks in advance :)