zerocrash
13-12-2005, 13:56
Hi all... i got this problem and i can't find a answer to it - so i hope you guys could help me out on this.
I connect my USB-stick to my WL500g and open up the Statuslog and find this - it seems to the router had figured out the type and vendor of the USB-stick - but it then makes it to a webcam???
Dec 13 14:21:57 kernel: hub.c: new USB device 00:04.0-1, assigned address 2
Dec 13 14:21:57 kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Dec 13 14:21:57 kernel: Vendor: CREATIVE Model: NOMAD_MUVO Rev: 0001
Dec 13 14:21:57 kernel: Type: Direct-Access ANSI SCSI revision: 02
Dec 13 14:21:57 kernel: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Dec 13 14:21:57 kernel: SCSI device sda: 126977 512-byte hdwr sectors (65 MB)
Dec 13 14:21:58 kernel: sda: Write Protect is off
Dec 13 14:21:58 kernel: Partition check:
Dec 13 14:21:58 kernel: p1
Dec 13 14:21:58 USB webcam: attached
Dec 13 14:21:59 kernel: pwc Philips PCA645/646 + PCVC675/680/690 + PCVC730/740/750 webcam module version 8.12 loaded.
Dec 13 14:21:59 kernel: pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
Dec 13 14:21:59 kernel: pwc the Creative WebCam 5, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
Dec 13 14:21:59 kernel: usb.c: registered new driver Philips webcam
-- At this point i removed it again --
Dec 13 14:39:37 kernel: usb.c: USB disconnect on device 00:04.0-1 address 2
Dec 13 14:39:38 USB webcam: removed
Dec 13 14:39:38 kernel: usb.c: deregistering driver Philips webcam
Dec 13 14:39:38 kernel: pwc Philips webcam module removed.
But the USB-stick isn't a Webcam - duh... :rolleyes:
So how do i solve this problem? I would like to make an IPGraph based on a toturial in this forum.
Thanks for your help.
I connect my USB-stick to my WL500g and open up the Statuslog and find this - it seems to the router had figured out the type and vendor of the USB-stick - but it then makes it to a webcam???
Dec 13 14:21:57 kernel: hub.c: new USB device 00:04.0-1, assigned address 2
Dec 13 14:21:57 kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Dec 13 14:21:57 kernel: Vendor: CREATIVE Model: NOMAD_MUVO Rev: 0001
Dec 13 14:21:57 kernel: Type: Direct-Access ANSI SCSI revision: 02
Dec 13 14:21:57 kernel: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Dec 13 14:21:57 kernel: SCSI device sda: 126977 512-byte hdwr sectors (65 MB)
Dec 13 14:21:58 kernel: sda: Write Protect is off
Dec 13 14:21:58 kernel: Partition check:
Dec 13 14:21:58 kernel: p1
Dec 13 14:21:58 USB webcam: attached
Dec 13 14:21:59 kernel: pwc Philips PCA645/646 + PCVC675/680/690 + PCVC730/740/750 webcam module version 8.12 loaded.
Dec 13 14:21:59 kernel: pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
Dec 13 14:21:59 kernel: pwc the Creative WebCam 5, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
Dec 13 14:21:59 kernel: usb.c: registered new driver Philips webcam
-- At this point i removed it again --
Dec 13 14:39:37 kernel: usb.c: USB disconnect on device 00:04.0-1 address 2
Dec 13 14:39:38 USB webcam: removed
Dec 13 14:39:38 kernel: usb.c: deregistering driver Philips webcam
Dec 13 14:39:38 kernel: pwc Philips webcam module removed.
But the USB-stick isn't a Webcam - duh... :rolleyes:
So how do i solve this problem? I would like to make an IPGraph based on a toturial in this forum.
Thanks for your help.